• 대한기계학회논문집A
• /
• 제37권9호
• /
• pp.1159-1168
• /
• 2013

가압형 경수로 원자로의 압력용기 상부헤드 관통노즐 J-groove 용접부 주변에서 일차수응력부식균열(PWSCC)로 인한 냉각수 누설사례가 발생하고 있다. 본 연구에서는 PWSCC 의 주요 원인 중 하나인 용접 잔류응력을 유한요소 해석을 이용해 평가하고 원자력 발전소의 정상가동 조건을 해석에 반영하는 방법이 용접잔류응력 분포에 미치는 영향에 대한 분석을 수행하였다. 또한 반복되는 원자력 발전소의 가동 주기가 용접잔류응력 분포에 미치는 영향을 확인하여 정상가동조건에서의 정확한 용접 잔류응력을 예측할 수 있는 방법을 분석하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제15권3호
• /
• pp.13-19
• /
• 2013

Superconducting field coils using a high-temperature superconducting (HTS) wires with high current density generate high magnetic field of 2 to 5 [T] and electromagnetic force (Lorentz force) acting on the superconducting field coils also become a very strong from the point of view of a mechanical characteristics. Because mechanical stress caused by these powerful electromagnetic force is one of the factors which worsens the critical current performance and structural characteristics of HTS wire, the mechanical stress analysis should be performed when designing the superconducting field coils. In this paper, as part of structural design of superconducting field coils for 17 MW class superconducting ship propulsion motor, mechanical stress acting on the superconducting field coils was analyzed and structural safety was also determined by the coupling analysis system that is consists of commercial electromagnetic field analysis program and structural analysis program.

• Journal of Mechanical Science and Technology
• /
• 제15권2호
• /
• pp.172-179
• /
• 2001

The effects of the interface and two holes located near the crack path in the hybrid specimen on the dynamic crack propagation behavior have been investigated using dynamic photoelasticity with the aid of Cranz-Shardin type high speed camera system. The dynamic stress field around the dynamically propagating interface crack tip in the three point bending specimens under a dynamic load applied by a hammer dropped from 0.6m high without initial velocity are recorded. The complex stress intensity factors for the dynamically propagating interface crack are extracted by using a overdeterministic least square method. Theoretical dynamic interface isochromatic fringe loops generated by using the numerically determined complex stress intensity factors are compared with the experimental results. Furthermore, the influence of the hole to the dynamic interface crack velocities has been investigated experimentally.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.187-192
• /
• 2001

Cracks in mechanical joints is generally under mixed-mode and there is the critical inclined angle at which mode I stress intensity factor becomes maximum. In order to evaluate the fatigue life of cracks in mechanical joints, horizontal crack normal to the applied load and located on minimum cross section is major concern but critical inclined crack must also be considered. In this paper mixed-mode fatigue crack growth test is performed for horizontal crack and critical inclined crack in mechanical joints. Fatigue crack growth path is predicted by maximum tangential stress criterion using mode I and mode II stress intensity factors obtained from weight function method, and fatigue crack growth rates of horizontal and inclined crack are compared.

• 대한기계학회논문집A
• /
• 제21권9호
• /
• pp.1498-1506
• /
• 1997

Procedures are presented for influence of shot peening on fatigue strength, fatigue life and effects of shot peening are discussed from experiments were taken between shot peened and unpeened SPS5, SM45C specimens. After the residual stress on shot peened specimens was measured by X-ray diffractometer, rotating bending fatigue tests were carried out. In addition, the compressive residual stress profile was obtained by the superposition method of three stresses which is based on Al-Obaid's equation. Predicted fatigue life considering residual stress profile which was obtained by the Al-Obaid's equation and another predicted fatigue life considering residual stress profile which was measured in test were compared. For the purpose of predicting fatigue life, Morrow's equation considering the residual stress and mean stress was used.

• 접착 및 계면
• /
• 제7권4호
• /
• pp.18-23
• /
• 2006

The influence of the notch length on the stress distribution of mid-bondline and adherend was investigated using elasto-plastic finite element method. The results from the simulation showed that peak stress of mid-bondline decreased markedly as adherend with notch in the middle of lap zone, and the stress in the middle of joint with low stress originally increased evidently. All the peak stresses decreased firstly and increased again as the length of notch increased. The relative higher peak stress appeared at the point near the notch of adherend where might be failed previously during the loading procedure.

• KSTLE International Journal
• /
• 제5권1호
• /
• pp.14-22
• /
• 2004

The sub-surface stress field beneath the gear's contact surface caused by the surface pressure in lubricated condition is analyzed. To evaluate the influence of the clearances between a gear tooth and a pinion tooth on the stress field, two kinds of tooth profile models - conventional cylinder contact model and new numerical model - were chosen. Kinematics of the gear is taken into account to obtain the numerical model which is the accurate geometric clearances between a gear tooth and a pinion tooth. Transient elasto-hydrodynamic lubrication (EHL) analysis is performed to get the surface pressure. The sub-stress field is obtained by using Love's rectangular patch solution. The analysis results show that the sub-surface stress is quite dependent on both the surface pressures and the profile models. The maximum effective stress of the new model is lower than that of the old model. The depth where the maximum effective stress occurs in the new model is not proportional to the intensity of the external load.

• Nuclear Engineering and Technology
• /
• 제48권4호
• /
• pp.1036-1046
• /
• 2016

We propose a primary water stress corrosion cracking (PWSCC) initiation model of Alloy 600 that considers the stress triaxiality factor to apply to finite element analysis. We investigated the correlation between stress triaxiality effects and PWSCC growth behavior in cold-worked Alloy 600 stream generator tubes, and identified an additional stress triaxiality factor that can be added to Garud's PWSCC initiation model. By applying the proposed PWSCC initiation model considering the stress triaxiality factor, PWSCC growth simulations based on the macroscopic phenomenological damage mechanics approach were carried out on the PWSCC growth tests of various cold-worked Alloy 600 steam generator tubes and compact tension specimens. As a result, PWSCC growth behavior results from the finite element prediction are in good agreement with the experimental results.

• 한국세라믹학회지
• /
• 제30권10호
• /
• pp.859-865
• /
• 1993

Morphotropic tetragonal and rhombohederal phase boundary(MPB) in PZT system was calculated and the effect of mechanical stress and electric field on the MPB was examined using phenomenological thermodynamic theory proposed by Devonshire. Mechanical stress and electric field was calculated to change free energies of phases and shift MPB. The stable composition range of the phase, of which spontaneous strain and spontaneous polarization aligned to the direction of tensile stress or electirc field, was expanded.

• 대한기계학회논문집A
• /
• 제20권2호
• /
• pp.450-460
• /
• 1996

To investigate the effect of stress wave propagation for crack tip, impact responses of two-dimensional plates with oblique cracks are investigated by a numerical method. In the numerical analysis, the finite element method is used in space domain discretization and the Newmark constant acceleration algorithm is used in time integration. According to the numerical results from the impact response analysis. it is found that the stress fields are bisected at the crack surface and the parts of stress intensity are moved along the crack face. The crack tip stress fields are yaried rapidly. The magnitude of crack tip stress fields are converted to dynamic stress intensity factor. Dynamic sress intensity factor appears when the stress wave has reached at the crack tip and the aspect of change of dynamic stress intensity factor is shown to be the same as the part of the flow of stress intensity.