• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.83-87
• /
• 2002

Aerospace industries are widely using honeycomb sandwich structures that it has high specific strength and stiffness, chemical material resistance and fatigue resistance. But, in repairing process of damaged areas, one of the problems is that delamination can be occurred in the sound areas during and/or after the exposure to the elevated curing temperature in case that the repair process is repeated. Therefore, this study was conducted Flatwise tensile, Drum peel and Long beam flexural strength tests to evaluate the degree of degradation of mechanical properties of the honeycomb sandwich structures by affecting thermal aging. As the results, the decrease of mechanical strength was observed at the specific specimen which is exposed over 50hrs at $127^{\circ}C$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.3
• /
• pp.48-55
• /
• 2003

This study investigates the effect of temperature and electric field strength on the Bingham characteristics of Electro-Rheological(ER) fluids which change their Yield shear stress and viscosity by temperature and electric field strength. It is found that under constant temperature the Yield sheal stress and viscosity of ER fluids proportionally increase with the applied electric field strength, and under constant applied electric field strength the Yield shear stress and viscosity of ER fluids decrease with the increasing temperature. These results are considered to be applied to the fluid and pneumatic power industry.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.520-525
• /
• 2001

It's strongly recommended to check upon the slope stability of soil nearby railroad, since the freezing-thawing repeat in long term may cause decrease of slope stability. The study is, therefore, focused on the strength characteristic transformation of soil, measuring it experimentally, throughout physical and mechanical tests operated by the freezing-thawing repeat tests. The sampling of weathered soil used for the embankment materials along the domestic railway lines are classified by parent-rock, and then collected after it in the first hand. It tells that Uniaxial strength and axial strain were decreased simultaneously as the frequency of freezing-thawing repeat increased and its range was reduced into 25～85 percentage off comparing to uniaxial strength of unfreezing-soils when about 100 times of freezing-thawing repeats occurred. Following the result of direct shear tests, the cohesion of freezing-soil with freezing-thawing repeats shows 11∼60 percentage less than that of unfreezing-soil but the change of internal friction angle of the soil is extremely slight, enough to ignore. As a result. it could be found that strength characteristic transformation has highly correlated with freezing-thawing repeat.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1760-1769
• /
• 2007

The cut slope sliding which has been frequently encountered in Pohang area has been reported due to the rapid reduction of shear strength in mudstone after being exposed to the air. Mudstone has characteristics that it has high enough strength and stiffness in a dry condition, but the strength and stiffness decrease in a wet condition with groundwater infiltration. The case study in this paper shows that mudstone which had enough strength in a boring stage has lost the strength after installing PRD steel pipe pile inducing an insufficient bearing capacity, which has been ascertained by the static load test. Test construction has been performed to investigate the most favorable method for increasing a pile bearing capacity in mudstone with various methods such as MSG (Micro Silica Grouting) around the tip and side of a pile, the perimeter grouting combined with Micro pile reinforcement, and concrete filling after tip reinforcing grouting. From the test construction, MSG has been turned out to be the most favorable method for increasing a pile bearing capacity in mudstone, which has been confirmed by the static load test.

• Journal of Technologic Dentistry
• /
• v.25 no.1
• /
• pp.71-79
• /
• 2003

The purpose of this study was to investigate bond strength of denture base resin repaired according to contamination. One commercial denture base resin and two different kinds of relines resin were tested; Lusiton 199(denture base resin), Vertex(reline resin) and TokusoRebase(repair resin). The specimens were processed according to the manufacturer's instructions to cured denture base resin(polymethylmethacrylate; PMMA) and reline resin. Bond strengths were examined by use of a three-point transverse flexural strength test. Data were analyzed with two-factor analysis of variance and Duncan's post-hoc test at $\alpha$=0.05. Generally, the bondstrength of heat-cured resin(Lusiton 199) was higher than the other resins. The contaminations produced an decrease in bond strength. Therefore the contamination, such as saliva or water must be avoided during the laboratory repair procedures.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.10a
• /
• pp.113-114
• /
• 2016

In this study, various fats and oils were soaked in low-strength mortar to experiment what kind of fats and oils had the worst effect on low-strength mortar; it went as follows. For rate of change in length of fat and oil soaking, there was an increase in the order of pig fat, bio-diesel, grape seed oil, and water; in the case of olive oil it was destroyed within 56 days. For rate of change in mass, there was an increase in the order of bio-diesel, water, pig fat, grape seed oil, and olive oil. For relative motion elastic coefficient, there was a decrease in the order of olive oil, grape seed oil, and water. On the whole, pig fat, bio-diesel, and olive oil were shown to have the worst effect on low-strength mortar.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.75-76
• /
• 2017

In the case of B / a 1: 3, the intensity when the substitution rate increased to 15% showed a tendency to decrease, but it turned out that the strength increased at the substitution rate of 20%. In the case of B / a 1: 4 and 1: 5, it was found that when the substitution rate at the substitution rate of 10% was the highest and the substitution rate increased further, the strength was reduced. However, since the test body does not exist at the age of 3 days and the age of 7 days at the substitution rate of 0%, there is no specimen, so blast furnace slag binder substitution for increasing strength of refractory mortar is judged to be meaningless.

• Journal of Welding and Joining
• /
• v.26 no.2
• /
• pp.69-74
• /
• 2008

590MPa grade weldable steels were gas metal arc welded with flux cored wires. Welding parameters such as current, voltage, and speed were varied independently. Effects of each parameter on the strength and chemical composition of weld metal were investigated. Increase of voltage caused decrease of weld metal tensile strength due to the low recovery of alloying elements such as carbon and manganese. On the contrary, increase of current and speed resulted in increase of weld metal strength because of higher recovery of the alloying elements.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.05a
• /
• pp.251-254
• /
• 2006

In this paper, cutting qualifies and fracture strength of silicon dies by laser dicing are investigated. Laser micromachining is the non-contact process using thermal ablation and evaporation mechanisms. By these mechanisms, debris is generated and stick on the surface of wafer, which is the problem to apply laser dicing to semiconductor manufacture process. Unlike mechanical sawing using diamond blade, chipping on the surface and crack on the back side of wafer isn't made by laser dicing. Die strength by laser dicing is measured via the three-point bending test and is compared with the die strength by mechanical sawing. As a results, die strength by the laser dicing shows a decrease of 50% in compared with die strength by the mechanical sawing.

• Journal of Biomedical Engineering Research
• /
• v.18 no.1
• /
• pp.1-8
• /
• 1997

This study was performed to evaluate the effect of resin and filler type on the compressive strength of light-activated composite resins. Experimental composite resins containing either amorphous spherical silica or crushed quartz in two matrix resins of BisGMA/TEGDMA and UTMA/TEGDMA were prepared and the specimens of 3 m in diameter and 6m in length were made. Compressive test was subjected to a crosshead speed of 0.5 mm/min, and the fracture surFaces were examined by SEM. The compressive strength of UTMA-based composite resin was higher than that of BisGMA-based composite resin. The loading rate of spherical silica was higher than that of crushed silica when the size dis- tribution of fillers was same. Strength decrease of Bis-GMA-based composite resin was severer than that of UTMA-based composite resin in a $37^{\circ}$c water environment. Fracture surface showed that the composite resin failure developed along the matrix resin and the filler/resin interface region.