• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 추계 학술논문 발표대회
• /
• pp.154-155
• /
• 2016

Oyster shell is light weighted and its strength characteristic is similar to sand. So we produced mortar test piece using grounded oyster shell powder under 0.5mm, which is a standard of fine aggregate, and reviewed strength properties according to water cement ratio. In our test, we used two kinds of oyster shell particles: below 0.6mm and 1.2~2.5mm. Water cement ratio is varied 40% to 100% and we found that flexural strength and compressive strength are decreased in higher water cement ratio.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2005년도 학술발표논문집
• /
• pp.361-366
• /
• 2005

Since most soils exist above the ground water table, negative pore pressure exist in unsaturated soils. Negative pore water pressure in unsaturated soil affects the soil structure and degree of saturation and it is important for accurate evaluation of unsaturate flow and behavior. This negative pore pressure is called a matric suction which causes an increased shear strength. Therefore, it is required that the effect of increase in the shear strength should be included in a geotechnical analysis. From the test result, the influence of net confining pressure and matric suction on the shear strength was analyzed and strength parameter was increased with matric suction increase and a unliner relationship was found to relate matric suction and shear strength.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.460-467
• /
• 1997

Compared to normal-strength concrete, high-strength concrete has the lower lateral expansion capacity caused by the higher elastic modulus and the lower internal crack characteristic. Therefore, the effect of the lateral confining action of hoops appears slowly and also in inefficient Nevertheless. it has been reported that the strength and deformation capacity of high-strength concrete is improved by well-distributed hoops. Due to that argument, this investigation has been compared and analyzed by the experimental works on the deformation capacity and the confinement mechanism of high-strength concrete shear wall of the high-rise building reinforced by rectangular steel tubes and rectangular hoops at both edges of the shear wall.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(I)
• /
• pp.709-714
• /
• 2002

Recently, the applications of corrugated plates(or folded plates) are increasing due to economic and structural advantages in certain situations. And, because of the higher strength of corrugated plates than flat plates, the usage of the corrugated plates is increasing. So there are many necessities for specifications of corrugated plates. For flat plates, there are many design details in almost specifications. However, there are no detail design guides such as shear strength except the bending strength and the normal strength. So, it is difficult for engineers to design structures consist of corrugated plates. Therefore, a provision is necessary for engineers to refer for designing corrugated plates. The conclusion of this study shows a formula that helps to determine the shear strength of corrugated plates under various geometric conditions ; the size of corrugation ; the curvature of corrugation and ; the thickness of the corrugated plate. Also, it shows that corrugated plates have higher shear buckling strength than flat plates.

• Advances in materials Research
• /
• 제8권2호
• /
• pp.103-115
• /
• 2019

Polypropylene (PP) fibers for making fabric which is used for packing cement have a high strength and high tear resistance. Due to these excellent properties the present study investigates the effect of PP fibers on the mechanical strength of concrete. Mechanical strength parameters such as compressive strength, splitting tensile strength and flexural strength are evaluated. Structural integrity of concrete using Ultrasonic Pulse Velocity (UPV) was also studied. Concrete containing PP fibers in percentage of 0%, 0.15%, 0.25%, 0.5% and 0.75% was developed with a characteristic compressive strength of 25 MPa. Concrete cubes, cylinder and prismatic specimens were cast and tested. It was found that the UPV values recorded for all specimens were of the similar order. Test results indicated the used of PP fibers can significantly improve the flexural and splitting tensile strengths of concrete materials whereas it resulted a decreased in compressive strength. The relative increase in split tensile and flexural strength was optimum at a fiber dosage of 0.5% and a mild decreased were observed in 28 days compressive strength. The findings in this paper suggested that PP fibers deriving from these waste cement bags are a feasible fiber option for fiber-reinforced concrete productions.

• 한국추진공학회지
• /
• 제1권1호
• /
• pp.111-121
• /
• 1997

본 연구에서는 탄소/에폭시 복합재료의 기계적 결합부위의 결합강도 예측을 위한 구조해석과 실험을 수행하였다. 복합재료 구조물의 Joint설계에 있어 베어링 파괴는 대단히 중요한 파괴형태 중하나이다. 그래서 본 연구에서는 베어링 파괴를 해석적으로 예측하고 실험적으로 확인하였다. 순수인장 파괴(Net Tension Failure)와 베어링 파괴(Bearing Failure) 실험을 위해서 각각 두 가지 형상의 시편을 선택하였다. 기계적 결합강도 예측에 사용된 방법은 특성길이(Characteristic Length)법과 연관시킨 Yamada-Sun 파괴기준(Failure Criterion)과 Tsai-Hill 최대일 이론이다. 그리고 인장특성길이와 압축특성길이는 실험을 통하여 얻어지며, 특히 압축특성길이 결정은 최근에 착안된 베어링파괴 실험으로부터 결정하였다. 위와 같은 예측 방법을 준등방성(Quasi-Isotropic) Carbon/Epoxy HT245/RS3232에 적용하였다. 연구결과, 이론적인 복합재료 파괴예측이 실험결과와 잘 일치함을 확인할 수 있었다.

• 전기의세계
• /
• 제30권6호
• /
• pp.357-365
• /
• 1981

When electronegative gas SF$_{6}$ is dissolved and charged with insulating oil, the effect caused in the process by electronegative characteristic is studied and also the pressure effect caused by electronegative SF$_{6}$ acting on the liquid-level is examined respectively. When inert gas Ar is used to find a pressure effect acting on the liquid-level, its effect on dielectric strength is considered in the experiment. With three kinds of impulse voltage different in the duration of wave front and wave tail, a brief experiment if carried out ot see the effects on the dielectric breakdown characteristic as the wave is changing; either if I$_{2}$ and SF$_{6}$ are added to the insulating oil, or if the oil pressure is increased by Ar the dielectric strength becomes great and the longer the duration of wave front is, the greater the increase of the breakdown voltage, because I$_{2}$ added by a small quantity brings about some hirderance in the formation of gas phase. Likewise, the greater the changed pressure is, the greater the incerase of the breakdown voltage. When SF$_{6}$ is charged, the electronegative characteristic is prevailing at the time of low balanced pressure, and the pressure effect at the time of high balanced pressure.ressure.

• 해양환경안전학회지
• /
• 제13권3호
• /
• pp.223-228
• /
• 2007

본 논문은 선박용 알루미늄 합금에 대하여 TIG, MIG 그리고 로봇을 이용한 용접 등과 같은 다양한 용접기술을 적용하여 기계적 특성을 평가하였다. TIG 용접을 실시하였을 경우는 항복강도, 인장강도 그리고 연신율은 모재에 비하여 각각 83.9%, 64.6% 그리고 21.9%를 나타냈다. MIG 용접은 ER5356 용접봉을 사용하여 용접한 경우 ER5183 용접봉을 사용한 경우에 비하여 기계적 특성이 대략 2-4% 정도 개선된 효과가 관찰되었다. 또한 로봇을 이용한 용접을 실시한 경우는 5456-H116 모재에 비하여 5083O 모재의 경우가 양호한 기계적 특성을 나타냈다.

• 한국건축시공학회지
• /
• 제5권2호
• /
• pp.89-95
• /
• 2005

Various tests are performed with the recycled concrete including compressive strength, flexural strength, splitting tensile strength, bonding strength and chloride ion penetration test. The basic data obtained from the presented test could be accumulated for the purpose of utilization in concrete structure. Most of the strength tests show that strength decrease a little extent with increasing substitution ratio of recycled coarse aggregate except splitting tensile test for the concrete with $100\%$ recycled fine aggregate. But in case of the $50\%$ substitution of recycled coarse aggregate, compressive strength, flexural strength and bonding strength are almost equal to the normal concrete. Chloride ion penetration test shows that the penetration amounts of chloride ion becomes more in proportion to the substitution ratio of recycled aggregate. But most of the results show that the permeability of recycled concrete is proper to use. The results of present study nay imply that the use of recycled aggregate for steam curing concrete is possible but the substitution ratio of recycled aggregate should be determined through further studies.

• Advances in concrete construction
• /
• 제1권4호
• /
• pp.341-358
• /
• 2013

Due to fast growth in urbanisation, a highly developed infrastructure is essential for economic growth and prosperity. One of the major problems is to preserve, maintain, and retrofit these structures. To meet the requirements of construction industry, the basic information on all the mechanical properties of various concretes is essential. This paper presents the details of development of various concretes, namely, normal strength concrete (around 50 MPa), high strength concrete (around 85 MPa) and ultra high strength concrete (UHSC) (around 120 MPa) including their mechanical properties. The various mechanical properties such as compressive strength, split tensile strength, modulus of elasticity, fracture energy and tensile stress vs crack width have been obtained from the respective test results. It is observed from the studies that a higher value of compressive strength, split tensile strength and fracture energy is achieved in the case of UHSC, which can be attributed to the contribution at different scales viz., at the meso scale due to the fibers and at the micro scale due to the close packing of grains which is on account of good grading of the particles. Micro structure of UHSC mix has been examined for various magnifications to identify the pores if any present in the mix. Brief note on characteristic length and brittleness number has been given.