• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1192-1202
• /
• 1994

Fatigue behavior and life prediction were presented for thermal-mechanical and isothermal low cycle fatigue of 12Cr forged steel used for high temperature applications. In-phase and out-of-phase thermal-mechanical fatigue test at 350 to 600.deg. C and isothermal low cycle fatigue test at 600.deg. C were conducted using smooth cylindrical hollow specimen under strain-control with total strain ranges from 0.006 to 0.015. Cyclic softening behavior was observed regardless of thermal-mechanical and isothermal fatigue tests. The phase difference between temperature and strain in thermal-mechanical fatigue resulted in significantly shorter fatigue life for out-of-phase than for in-phase. The difference in fatigue lives was dependent upon the magnitudes of inelastic strain ranges and mean stresses. Increase in inelastic strain range showed a tendency of intergranular cracking and decrease in fatigue life, especially for out-of-phase thermal-mechanical fatigue. Thermal-mechanical fatigue life prediction was made by partitioning the strain ranges of the hysteresis loops and the results of isothermal low cycle fatigue tests which were performed under the combination of slow and fast strain rates. Predicted fatigue lives for out-of-phase using the strain range partitioning method showed an excellent agreement with the actual out-of-phase thermal-mechanical fatigue lives within a factor of 1.5. Conventional strain range partitioning method exhibited a poor accuracy in the prediction of in-phase thermal-mechanical fatigue lives, which was quite improved conservatively by a proposed strain range partitioning method.

• Fisheries and Aquatic Sciences
• /
• 제14권4호
• /
• pp.333-337
• /
• 2011

A new and a unique Brachionus rotifer was found in Hwajinpo coastal lagoon in Gangwon Province, South Korea. This Brachionus certainly originated from the wild rather than from aquaculture stations because Hwajinpo coastal lagoon has been under rigorous control as a military protected area and therefore could not have been contaminated by aquaculture stations. The new strain was identified as Brachionus rotundiformis based upon its morphological characteristics. The parthenogenetic female of this new rotifer strain typically shows characters similar to those of B. rotundiformis, such as the pot shape of the body, rounded dorsal plate compared with flattened ventral plate, elliptical mictic egg, four frontal spines, six pointed occipital spines, non-nodal foot, two toes, trophi typical of the Brachionus genus with five uncus plates resembling comb teeth, one wide symmetrical manubrium and ramus, and no stiffened spine as is seen in freshwater Brachionus rotifers. Moreover, its lorica was rather small in size compared with other common rotifer strains that serve as live-food organisms (Guam, Thai, and Bali strains). This new and unique Korean brackish rotifer, a B. rotundiformis strain, was therefore named the National Fisheries Research and Development Institute (NFRDI) $N^{\circ}1$ rotifer strain.

• 한국식생활문화학회지
• /
• 제34권2호
• /
• pp.208-216
• /
• 2019

Leuconostoc spp. are generally utilized as kimchi starters, because these strains are expected to have beneficial effects on kimchi fermentation, including improvement of sensory characteristics. Here, we developed a detection method for verifying the presence of the kimchi starter Leuconostoc mesenteroides WiKim33, which is used for control of kimchi fermentation. A primer set for multiplex polymerase chain reaction was designed based on the nucleotide sequence of the plasmids in strain WiKim33, and their specificity was validated against 45 different strains of Leuconostoc spp. and 30 other strains. Furthermore, the starter strain consistently tested positive, regardless of the presence of other bacterial species in starter kimchi during the fermentation period. Our findings showed that application of a strain-specific primer set for strain WiKim33 presented a rapid, sensitive, and specific method for detection of this kimchi starter strain during natural kimchi fermentation.

• 한국미생물·생명공학회지
• /
• 제49권3호
• /
• pp.384-390
• /
• 2021

A Gram-negative, aerobic, motile by gliding, and rod-shaped marine bacterium, designated CE67^T was isolated from the marine sponge Callyspongia elegans on Biyang-do in Jeju Island. The CE67^T strain grew optimally at 25℃, pH 7.5, and in the presence of 2-3% (w/v) NaCl. Phylogenetic analysis based on 16S rRNA gene sequence showed that strain CE67^T was related to the genus Aureivirga and had the highest 16S rRNA gene sequence similarity to the Aureivirga marina VIII.04^T type strain (96.3%). The primary fatty acids (>10%) of strain CE67^T were iso-C_15:0 (35.3%) and iso-C_17:0 3OH (21.8%). The polar lipid profile of strain CE67^T contained phosphatidylethanolamine, unidentified aminolipids, and unidentified lipids. The predominant menaquinone was MK-6. The DNA G+C content was 29.1 mol%. Based on the polyphasic taxonomic analysis, strain CE67^T was determined to be a representative novel species of the genus Aureivirga for which we propose the name Aureivirga callyspongiae sp. nov., whose strain type is CE67^T (=KCTC 42847^T=JCM 34566^T).

• 드라이브 ㆍ 컨트롤
• /
• 제20권1호
• /
• pp.41-47
• /
• 2023

The aim of this study was to develop a method for installing strain gauges on moving, lubricating oil-filled, and sealed parts, such as drive shafts of equipment, including construction machinery. A measuring device was constructed using an embedded CPU and an IoT sensor to measure the strain of the strain gauge, which allowed for the measurement of axial torque and axial force, and subsequent analysis. To verify the performance of the developed device, the axial torque and axial force of the forklift were measured during operation using a strain gauge attached to the inside of the drive shaft. This study confirmed the possibility of measuring and analyzing the strain of a moving part, such as the inside of a drive shaft, which is sealed and filled with hydraulic oil.

• Structural Monitoring and Maintenance
• /
• 제10권2호
• /
• pp.155-174
• /
• 2023

High performance concrete (HPC) has been extensively used in thin overlay for repair purpose due to its excellent strength and durability. This paper presents an experiment, where the sensor-instrumented HPC overlays have been followed by dynamic strain and moisture content monitoring for 1 year, under normal traffic. The vibrating wire and soil moisture sensors were embedded in overlay before construction. Four given HPC mixes (2 original mixes and their shrinkage-modified mixes) were used for overlays to contrast the strain and moisture results. A calibration method to accurately measure the moisture content for a given concrete mixture using soil moisture sensor was established. The monitoring results indicated that the modified mixes performed much better than the original mixes in shrinkage cracking control. Weather condition and concrete maturity at early age greatly affected the strain in concrete. The strain in HPC overlay was primarily in longitudinal direction, leading to transverse cracks. Additionally, the most moisture loss in concrete occurred at early age. Its rate was very dependent on weather. After one year, cracking survey was carried out by vision to verify the strain direction and no cracks observed in shrinkage modified mixes.

• 열처리공학회지
• /
• 제16권3호
• /
• pp.141-147
• /
• 2003

The effects of heat treatment on the fatigue life and welding residual stress of welded plates were investigated in this study. The plates were welded by flux cored arc welding process, and post weld heat treated at $600^{\circ}C$ for 1 hour. The residual stresses of welded plates before and after post weld heat treatment were measured by hole drilling method. To measure the fatigue life of welded plates, low cycle fatigue tests under strain control and high cycle fatigue tests under load control were performed respectively, by using cylindrical specimens containing weld metal and heat affected zone. The obtained result shows that the post weld heat treatment reduces the residual stress, and resultantly changes the fatigue life of welded plate. Goodman diagrammatic analysis has also been performed to study the effect of post weld heat treatment on the high cycle fatigue life.

• 소성∙가공
• /
• 제26권5호
• /
• pp.314-322
• /
• 2017

In the high-speed forming analysis, dynamic material properties considering a high strain rate are required. The split Hopkinson pressure bar (SHPB) experiment was performed for measuring dynamic material properties under high strain rate. The pulse shaping method was used to improve the accuracy of the SHPB experiment. A pulse shaper attached to the front of the incident bar was used for specimen dynamic stress equilibrium through stress wave control. Numerical analysis and SHPB test were performed to verify whether the pulse shaper affects the dynamic stress equilibrium in copper and Al6061 specimens. The results of SHPB test and numerical analysis show that the pulse shaper contributes to the dynamic stress equilibrium. Based on the improved stress equilibrium using a pulse shaper, the flow stress curves for copper and Al6061 materials were obtained at strain rates of 1344.4/sec and 1291.6/sec, respectively.

• 대한기계학회논문집A
• /
• 제20권4호
• /
• pp.1290-1300
• /
• 1996

The finite element method, based on rigid-plastic formulation, is widely used to simulate metal forming processes. In order to improve the computational efficiency of the rigid-plastic FEM, one-point integration is used to evaluate the stiffness matrix with four-node rectangular elements and eight-node brick elements. In order to control the hourglass modes, hourglass strain rate components were introduced and included in the effective strain rate definition, Numerical tests have shown that the proposed one-point integration scheme reduces the stiffness matrix evaluation time without deteriorating the convergence behavior of Newton-Raphson method. Simulations of a ring compression, a plane-strain closed-die forging and the three-dimensional spike forging processes were carried out by using the proposed integration method. The simulation results are compared to those obtained by applying the conventional integraiton method in terms of the solution accuracy and computational efficiency.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1998년도 제13차 학술회의논문집
• /
• pp.380-385
• /
• 1998