• 콘크리트학회논문집
• /
• 제20권3호
• /
• pp.299-305
• /
• 2008

본 연구는 탄소섬유판으로 보강된 철근콘크리트 부재의 전단거동 특성 및 파괴형상을 구명함에 그 목적이 있다. 이를 위하여 탄소섬유판의 형상, 섬유판 부착 간격 및 전단보강 철근량 등의 변수를 포함하는 실험 연구가 수행되었다. 본 실험 결과 탄소섬유판으로 보강된 철근콘크리트 부재의 전단 강성은 보강되지 않은 보에 비해 현저하게 개선되며 최대 전단강도 증진율은 100% 이상인 것으로 나타났다. 또한 탄소섬유판은 전단균열의 발생 및 진전을 억제하며, 적은 량의 탄소섬유판으로 보강했을 경우에도 전단강도의 증진 효과는 매우 좋은 것으로 나타났다. 본 연구에서는 탄소섬유판에 발생하는 변형률을 기본으로 하여 유효응력을 도출하였으며, 탄소섬유판으로 보강된 철근콘크리트 부재의 전단강도를 계산하였다. 이는 실험 결과와 잘 일치하는 것으로 나타났다.

• Composites Research
• /
• 제25권5호
• /
• pp.136-140
• /
• 2012

본 논문에서는 복합재료 IM rod가 적용된 골절부의 세포 분화과정을 모사하기 위해 유한요소해석을 실시하였다. 세포의 골화과정을 해석하기 위해 편향 변형률을 이용한 메카노 규제 이론을 사용하였으며, 반복 계산을 위해 Python 코드를 이용하여 서브루틴을 구현하였다. 치료에 가장 적절한 복합재료 IM rod의 강성을 찾기 위해 직물 탄소섬유/에폭시 복합재료 (WSN3k)의 적층각도를 바꾸어 해석을 실시하였다. 골절부에 가해지는 기계적 자극에 따른 치료효율을 비교하기 위해 두 가지 초기 하중 조건을 적용하였다. 그 결과 치료효율은 강성의 차이보다 하중에 의해 큰 영향을 받았으며, 초기 하중이 몸무게의 10%이고, 적층순서가 $[{\pm}45]_{nT}$일 때 치료효율이 가장 높았다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권2호
• /
• pp.123-132
• /
• 2014

The maritime sector is advancing with dedicated endeavor to reduce greenhouse gas in addressing issues with regards to global warming. Since 01 January 2013, the International Maritime Organization (IMO) regulation mandatory requirement for Energy Efficiency Design Index (EEDI) has been in place and should be satisfied by newly-built ships of more than 400 gross tonnage and the Ship Energy Efficiency Management Plan (SEEMP) for all ships type. Therefore, compliance to this necessitates planning during the design stage whereas verification can be carried-out through an acceptable method during sea trial. The MEPC-approved 2013 guidance, ISO 15016 and ISO 19019 on EEDI serves the purpose for calculation and verification of attained EEDI value. Individual ships EEDI value should be lower than the required value set by these regulations. The key factors for EEDI verification are power and speed assessment and their synchronization. The shaft power can be measured by telemeter system using strain gage during sea trial. However, calibration of shaft power onboard condition is complicated. Hence, it relies only on proficient technology that operates within the permitted ISO allowance. On the other hand, the ship speed can be measured and calibrated by differential ground positioning system (DGPS). An actual test on a newly-built vessel was carried out to assess the correlation of power and speed. The Energy-efficiency Design Index or Operational Indicator Monitoring System (EDiMS) software developed by the Dynamics Laboratory-Mokpo Maritime University (DL-MMU) and Green Marine Equipment RIS Center (GMERC) of Mokpo Maritime University was utilized for this investigation. In addition, the software can continuously monitor air emission and is a useful tool for inventory and ship energy management plan. This paper introduces the synchronization and identification method between shaft power and ship speed for EEDI verification in accordance with the ISO guidance.

• 대한기계학회논문집
• /
• 제10권1호
• /
• pp.25-33
• /
• 1986

본 연구에서는 선단요소 해법의 방법을 토대로 소형컴퓨터를 위한 비선형 유한요소의 개발을 시도한 것이다. 주로 참조한 선단요소 해법의 프로그램은 Hinton과 Owen이 작성한 프로그램이며 원판메모리를 최대로 활용하여, 활동변수를 최소화 시키므로써, 실제 소형컴퓨터인 HP-3000II(512KB) 컴퓨터에서 총 자유도가 1000정도 되는 유한요소까지는, 해석이 가능하도록 만들어지게 되었다. 이와같이 완성된 프로그램의 응용성과 신뢰성을 검토해 보기 위해서 표준 CT 시편의 유한요소 를 작성하여(124 element, 428 node, 941 freedom) 크랙선단에 형성되는 소성역의 형상과 소성변형 크기를 수치적으로 추적하여 본 결과, 실험결과와 매우 잘 일치함을 볼 수 있어서 프로그램의 신뢰성을 확인 할 수 있었다. 이때 실험은 SUS-304스테인 레스강단의 소성역을 형성시킨다음, 재결정 방법에 의해 소성역의 형상과 크기를 가시 화 및 정량화 하여서 계산결과와 비교 하였다.

• 한국지진공학회논문집
• /
• 제6권3호
• /
• pp.11-21
• /
• 2002

유연도법 섬유요소모델을 통하여 반복하중을 받는 철근콘크리트 교각의 비탄성 이력 거동을 추적하고 직접적인 방법에 의해 변위연성도 평가를 수행하였다. 철근 콘크리트 교각의 극한상태까지의 비탄성 거동을 합리적으로 추적하기 위해 인장강성거동, 기둥-기초면의 불연속 변위 등을 고려하여 철근과 콘크리트의 평균응력-평균변형률 관계, 접촉면요소 등을 실험과 잘 일치하는 기존의 해석 모델을 수정, 적용하였다. 또한 수치해석시 간편하게 적용할 수 있는 직접적인 방법에 의하여 교각의 연성능력을 평가하였으며, 항복변위 및 극한변위의 산출에 영향을 미치는 적분점의 위치, 콘크리트 압쇄 후 강루 철근의 low-cycle fatigue에 의한 파단 시점 등에 대하여 유연도법 섬유요소모델에 적용할 수 있는 값들을 제시하였다. 해석에 의한 변위연성도는 10%이내의 오차를 보이므로, 적용한 해석기법 및 모델에 의한 항복변위 및 극한변위의 평가는 타당하다고 할 수 있다.

• 소성∙가공
• /
• 제6권3호
• /
• pp.239-249
• /
• 1997

The behaviour of alloys in the semi-solid state strongly depends on the imposed stress state and on the morphology of the phase which can vary from dendritic to globular. To optimal net shape forging of semi-solid materials, it is important to investigate for filling phenomena in forging process of arbitrarily shaped dies. To produce a automotive part which has good mechanical property, the filling pattern according to die velocity and solid fraction distribution has to be estimated for arbitrarily shaped dies. Therefore, the estimation of filling characteristic in the forging simulation with arbitrarily shaped dies of semi-solid materials are calculated by finite element method with proposed algorithm. The proposed theoretical model and a various boundary conditions for arbitrarily shaped dies is investigated with the coupling calculation between the liquid phase flow and the solid phase deformation. The simulation process with arbitrarily shaped dies is performed to the isothermal conditions of two dimensional problems. To analysis of forging process by using semi-solid materials, a new stress-strain relationship is described, and forging analysis is performed by viscoelastic model for the solid phase and the Darcy's law for the liquid flow. The calculated results for forging force and filling limitations will be compared to experimental data. The filling simulation of simple products performed with the uniform billet temperature(584$^{\circ}C$) from the induction heating by the commercial package MAGMAsoft. The initial step of computation is the touching of semi-solid material with the end of die gate and the initial concept of proposed system just fit with the capability of MAGMAsoft.

• 한국재료학회지
• /
• 제5권8호
• /
• pp.936-944
• /
• 1995

본 논문에서는 저압 유기금속 기상성장(low pressure metal organic vapor phase epitaxy) 장치에 의해 성장된 InGaAsP/InP 구조의 상(phase) 분리현상(Spinodal 분해)이 photoluminescence (PL)의 강도와 반치폭(full-width at half maximum, FWHM)에 미치는 영향에 대해 연구하였다. 시료의 격자부정합은 double crystal x-ray diffractometer를 사용하여 측정하였고, InGaAsP에피막의 Spinodal분해조직은 투과전자현미경 (transmission electron microscopy, TEM)을 사용하여 관측하였다. 격자부정합에서 도출된 부정합응력과 Spinodal 모듈레이션의 주기(periodicity)와 밀접한 관계가 있음이 밝혀졌다. 또한 이러한 InGaAsP에피막의 미세조직 구조와 시료의 광전 특성이 어떤 관계가 있는지 알기 위해 PL 실험을 수행했으며, PL강도와 FWHM이 조성 모듈레이션의 주기에 강하게 의존한다는 것을 알 수 있었다. 이 현상을 심층적으로 연구하기 위해 부정합응력이 야기할 수 있는 interaction 탄성변형 에너지라는 새로운 함수를 유도하였으며 이에 의하여 실험결과를 설명할 수 있었다.

• 한국자동차공학회논문집
• /
• 제24권6호
• /
• pp.642-648
• /
• 2016

This paper deals with an analytical and experimental investigation to predict the axial thrust load that results from turbocharger operating conditions. The Axial forces acting on the turbocharger thrust bearing are caused by the unbalance between turbine wheel gas forces and compressor wheel air forces. It has a great influence on the friction losses, which reduces the efficiency and performance of high-speed turbocharger. This paper presents the calculation procedure for the axial thrust forces under operating conditions in a turbocharger. The first step is to determine the relationship between thrust forces and strains by experimental and numerical methods. The analysis results were verified by measuring the strains on a thrust bearing with the specially designed test device. And then, the operating strains and temperatures were measured to inversely calculate the thrust strains which were compensated the thermal effects. Therefore it's possible to calculate the magnitudes of the thrust forces under operating turbocharger by comparing the regenerated strains with the rig test results. It will possible to optimize the design of a thrust bearing for reducing the mechanical friction losses using the results.

• Earthquakes and Structures
• /
• 제10권6호
• /
• pp.1253-1272
• /
• 2016

For a nonlinear control system, there are many uncertainties, such as the structural model, controlled parameters and external loads. Although the significant progress has been achieved on the robust control of nonlinear systems through some researches on this issue, there are still some limitations, for instance, the complicated solving process, weak conservatism of system, involuted structures and high order of controllers. In this study, the computational structural mechanics and optimal control theory are adopted to address above problems. The induced norm is the eigenvalue problem in structural mechanics, i.e., the elastic stable Euler critical force or eigenfrequency of structural system. The segment mixed energy is introduced with a precise integration and an extended Wittrick-Williams (W-W) induced norm calculation method. This is then incorporated in the market-based control (MBC) theory and combined with the force analogy method (FAM) to solve the MBC robust strategy (R-MBC) of nonlinear systems. Finally, a single-degree-of-freedom (SDOF) system and a 9-stories steel frame structure are analyzed. The results are compared with those calculated by the $H{\infty}$-robust (R-$H{\infty}$) algorithm, and show the induced norm leads to the infinite control output as soon as it reaches the critical value. The R-MBC strategy has a better control effect than the R-$H{\infty}$ algorithm and has the advantage of strong strain capacity and short online computation time. Thus, it can be applied to large complex structures.

• 접착 및 계면
• /
• 제5권2호
• /
• pp.14-26
• /
• 2004

For reliable determination of mechanical characteristics of adhesively bonded joints used e.g. as input data for computer-aided design of complex components, the thick-adherend tensile-shear test according to ISO 11003-2 is the most important material testing method. Although the total displacement of the joint is measured across the polymer layer directly in the overlap zone in order to minimize the influence of the stepped adherends, the substrate deformation must be taken into account within the framework of the evaluation of the shear modulus and the maximum shear strain, at least when high-strength adhesives are applied. In the standard ISO 11003-2 version of 1993, it was prescribed to perform the substrate deformation correction by means of testing a one-piece reference specimen. The authors, however, pointed to the excessive demands on the measuring accuracy of the extensometers connected with this technique in industrial practice and alternatively proposed a numerical deformation analysis of a dummy specimen. This idea of a mathematical correction was included in the revised ISO 11003-2 version of 2001 but in the simplified form of an analytical method based on Hooke's law of elasticity for small strains. In the present work, it is shown that both calculation techniques yield considerably discordant results. As experimental assessment would require high-precision distance determination (e.g. laser extensometer), finite element analyses of the deformation behavior of the bonded joint are performed in order to estimate the accuracy of the obtained substrate deformation corrections. These simulations reveal that the numerical correction technique based on the finite element deformation modeling of the reference specimen leads to considerably more realistic results.