• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.5
• /
• pp.471-477
• /
• 2015

In this study, the property of crack propagation and growth at high tension steel plate existed with center crack is investigated. The behaviors of fracture mechanics due to existence or not of hole near the center crack in specimen and the length of crack length are investigated when the load is applied at the one side end of specimen. Stress, deformation and deformation of this specimen are evaluated through simulation analysis. By the analysis results at this study, stress intensity factors are obtained. The damage happened at machine or structure with crack or defect can be estimated on the basis of study results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.11 s.170
• /
• pp.1970-1981
• /
• 1999

The low-cycle fatigue behaviour of a SiC-particulate-reinforced Al-Si cast alloy with two different volume fractions has been investigated from a series of strain-control led fatigue tests with zero and nonzero tensile mean strains. The composites including the unreinforced matrix alloy, exhibited cyclic hardening behaviour, with more pronounced strain-hardening for the composites with a higher volume fraction of the SiC particles. For the tensile mean strain tests, the initial high tensile mean stress relaxed to zero for the ductile Al-Si alloy, resulting in no influence of the tensile mean strain on the fatigue life of the matrix alloy. However, tensile mean strain for the composite caused tensile mean stresses and reduced fatigue life. The pronounced effects of mean strain on the low-cycle fatigue life of the composite compared to the unreinforced matrix alloy were attributed to the initial large prestrain and non-relaxing high tensile mean stress in the composite with very limited ductility and Cyclic plasticity. Fatigue damage parameter using strain energy, density efficiently accounted for the mean stress effects. Predicted fatigue life using the damage parameter correlated fairly well with the experimental life within a factor of 3. Also, the fatigue damage parameter indicated the inferior life in the low-cycle regime and superior life in the high-cycle regime for the composite, compared to the unreinforced matrix alloy.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.217-220
• /
• 2009

고층 건물에 대한 구조 안전성 모니터링은 건물 특성상 계측 대상 부재가 많고 하중과 구조반응의 관계가 복잡하기 때문에 센싱 위치 선정의 어려움으로 그 적용에 한계가 있다. 본 논문에서는 고층 건물의 구조 건전도 모니터링을 위한 구조반응 계측위치를 선정하기 위해서 에너지 이론에 근거한 부재의 변위기여도 및 변형에너지밀도 개념을 도입하였다. 보, 기둥, 코어 전단벽, 그리고 아웃리거로 구성된 고층 건물을 대상으로 풍하중에 대한 부재 종류별 부재의 변위기여도 및 변형에너지밀도를 확인하고 전체 구조물의 거동과의 관계를 분석하여 고층 건물의 구조 건전도 모니터링을 위한 센싱 위치를 예상해보았다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.95-102
• /
• 2003

To define an analytical model for a structural system or to assess damage in the system, system identification(SI) methods have been developed and widely applied. The paper presents a method of determining optimal sensor location(OSL) based on the maximum likelihood approach, which is applicable to modal SI methods. To estimate unknown parameters reliably, it is necessary that the information provided by the experiment should be maximized. By applying the Cramer-Rao inequality, a Fisher information matrix in terms of the probability density function of measurements is obtained from a lower bound of the estimation error. The paper also proposes a scheme of determining of OSL on damaged structures by using maximum strain energy factor. Simulation studies have carried out to investigate the proposed OSL algorithm for both undamaged and damaged structures.

• Macromolecular Research
• /
• v.17 no.8
• /
• pp.585-590
• /
• 2009

The cure behaviors, dielectric characteristics and fracture toughness of diglycidylether of bisphenol-A (DGEBA)/poly(ethylene terephthalate) (PET) blend system were investigated. The degree of conversion for the DGEBA/PET blend system was measured using Fourier transform infrared (FTIR) spectroscopy. The cure kinetics were investigated by measuring the cure activation energies ($E_a$) with dynamic differential scanning calorimetry (DSC). The dielectric characteristic was examined by dielectric analysis (DEA). The mechanical properties were investigated by measuring the critical stress intensity factor ($K_{IC}$), critical strain energy release rate ($G_{IC}$), and impact strength test. As a result, DGEBAIPET was successfully blended. The Ea of the blend system was increased with increasing PET content to a maximum at 10 phr PET. The dielectric constant was decreased with increasing PET content. The mechanical properties of the blend system were also superior to those of the neat DGEBA. These results were attributed to the increased cross-linking density of the blend system, resulting from the interaction between the epoxy group of DGEBA and the carboxyl group of PET.

• Computers and Concrete
• /
• v.22 no.6
• /
• pp.539-550
• /
• 2018

Concrete is highly non-linear material which is originating from the transition zone in the form of micro-cracks, governs material response under various loadings. In this paper, the constitutive models published by many researchers have been used to generate novel stiffness parameters and constitutive curves for concrete. Following such linear material formulations, where the energy is conservative during the curvature, and a nonlinear contribution to the concrete has been made and investigated. In which, nonlinear concrete elastic modulus modeling has been developed that is capable-of representing concrete elasticity for grades ranging from 10 to 140 MPa. Thus, covering the grades range of concrete up to the ultra-high strength concrete, and replacing many concrete models that are valid for narrow ranges of concrete strength grades. This has been followed by the introduction of the nonlinear Hooke's law for the concrete material through the replacement of the Young constant modulus with the nonlinear modulus. In addition, the concept of concrete elasticity index (${\varphi}$) has been proposed and this factor has been introduced to account for the degradation of concrete stiffness in compression under increased loading as well as the multi-stages micro-cracking behavior of concrete under uniaxial compression. Finally, a sub-routine artificial neural network model has been developed to capture the concrete behavior that has been introduced to facilitate the prediction of concrete properties under increased loading.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.2
• /
• pp.91-95
• /
• 2009

To understand the effect of attachment substrate on the growth of benthic microalgae, we experimentally investigated the growth of benthic microalgae Nitzschia sp. (Jinhae Bay strain) with additions of glass beads in different sizes. The glass beads used in this study are 0.09-0.15 mm (G1), 0.25-0.50 mm (G2), 0.75-1.00 mm (G3) and 1.25-1.65 mm (G4). No addition of glass beads used as controls. Highest specific growth rate (0.37/day) and maximum cell density ($9,232{\pm}840$ cells/mL) of Nitzschia sp. showed at the smallest glass beads (G1), and the specific growth rate and maximum cell density were decreasing with increasing size of glass beads (specific growth rate and maximum cell density of G4 was 0.24/day and $6,397{\pm}524$ cells/mL, respectively). Moreover, specific growth rate of the control experiment (0.23/day) was significantly lower than their of G1 to G3 experiment. The results indicated that the attachment substrate for benthic microalgae as Nitzschia sp. is important factor which affecting the growth rate as well as cell density. Therefore, the physiological experiment of benthic microalgae seems to be necessary to preliminary experiment, which is addition or not of the attachment suitable substrate and the grain size for the target species of benthic microalgae.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.6 s.177
• /
• pp.1446-1455
• /
• 2000

Fatigue crack initiation and propagation behavior under cyclic biaxial loading has been investigated using thin-walled tubular specimen with a hole. Two types of biaxial loading system, i.e. cyclic tensile loading with super-imposed static torsional load and cyclic torsional loading with superimposed static tensile load, with various values of the biaxial loading ratio, $\tau$ s/ $\sigma$ max (or $\tau$ max/ $\sigma$s) were employed. Fatigue tests show that fatigue crack near the hole initiates and propagates at 900 and 450 direction to the longitudinal direction of the specimen under cyclic tensile and torsion loading with static biaxial stress, respectively, and the static biaxial stress doesn't have any great influence on fatigue crack initiation and growth direction. Stress analysis near the hole of the specimen shows that the crack around the hole initiates along the plane of maximum tangential stress range. Fatigue crack growth rates were evaluated as functions of equivalent stress intensity factor range, strain energy density factor range and crack tip opening displacement vector, respectively. It is shown that the biaxial mode fatigue crack growth rates can be relatively consistently predicted with these cyclic parameters.

• Elastomers and Composites
• /
• v.39 no.1
• /
• pp.42-50
• /
• 2004

In this work, the diglycidylether of bisphenol A (DGEBA) and modified polyurethane (PU) blends were initiated by N-benzylpyrazinium hexafluoroantimonate (BPH). The cure and fracture toughness of neat DGEBA with the addition of PU were investigated. The cure properties of DGEBA/PU blend system were examined by DSC and near-IR measurements. The fracture touhtness were investigated by measuring the critical stress intensity factor ($K_{IC}$) and the critical strain energy release rate ($G_{IC}$). According to the results, the maximum values of owe activation energy ($E_a$) and conversion (${\alpha}$) were found at 10 phr of PU. Also the $K_{IC}$ showed a similar behavior with the results of conversion. These results were probably due to increase of crosslinking density in the blends resulted from increase of the hydrogen bonding between the hydroxyl groups of DGEBA and isocyanate groups of PU.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.23 no.1
• /
• pp.27-44
• /
• 1993

This study was performed to investigate the changes of mandibular condyle by low calcium diet and the effects of irradiation on the bone in osteoporotic state. In order to carry out this experiment, 80 seven-week old Sprague-Dawley strain rats weighing about 150 gm were selected and equally divided into one experimental group of 40 rats and one control group with the remainder. The experimental group and the control group were then subdivided into two group and exposed to irradiation. The two irradiation groups received a single dose of 20 Gy on the jaw area only and irradiated with a cobalt-60 teletherapy unit. The rats in the control and experimental groups were serially terminated by fours on the 3rd, the 7th, the 14th, and the 21st day after irradiation. After termination, both sides of the dead rats mandibular condyle were removed and fixed with 10% neutral formalin. The bone mineral density of mandibular condyle was measured by use of dual energy X-ray bone densitometer(model DDX-alpha, Lunn Corp., U. S. A.). The mandibular condyle was radiographed with Hitex HA-80(Hitex Co., Japan). Thereafter, the obtained radiographs were observed, and the mandibular condyle was further decalcified and embedded in paraffin as the general method. The specimen sectioned and stained with hematoxylin-eosin, PAS and Rabbit Anti-Human Tumor Necrosis Factor-a observed by a light microscope. The obtained results were as follows: 1. In the non-irradiated group with the low calcium diet, the bone mineral density of the condyle was markedly decreased after 14 days, and decrease the number of trabeculae of the condyle and resorption of the calcified cartilaginous zone were observed after 3 days. On microscopic observations, the number nd size of trabeculae were decreased after 7 days of experiment. 2. In the irradiated group with the low calcium diet, the bone mineral density of the condyle was markedly decreased after 14 days and resorption of the calcified cartilaginous zone and decrease the number and coarse of the trabeculae of the condyle were observed. These findings were extended rather than in non-irradiated group with low calcium diet. On microscopic observations, many osteoclasts were detected and the number and size of trabeculae were somewhat decreased after 7 days. Also there was degenerative changes of tissues of bone marrow on the 14th day but that condition was restored on the 21st day of experiment. 3. In the irradiated group with normal diet, the bone mineral density of the condyle was somewhat decreased with times and degree of decrease of the number of trabeculae was somewhat larger than in the non-irradiated group with normal diet. On microscopic observations, the tissues of bone marrow were atrophic and degenerative changes but that condition was restored on the 21st day of experiment. 4. In immunocytochemical findings, in the irradiated and non-irradiated groups with low calcium diet, negative or partial positive response to TNF was observed, but positive response in the normal diet groups.