• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.919-924
• /
• 2000

Spray impingement model and fuel film formation model were developed and incorporated into the computational fluid dynamics code, STAR-CD. The spray/wall interaction process were modelled by considering the change of behaviour with surface temperature condition and fuel film formation. We divided behaviour of fuel droplets after impingement into stick, rebound and splash using Weber number and parameter K. Spray impingement model accounts for mass conservation, energy conservation and heat transfer to the impinging droplets. A fuel film formation model was developed by Integrating the continuity, the Navier-Stokes and the energy equations along the direction of fuel film thickness. The validation of the model was conducted using diesel spray experimental data and gasoline spray impingement experiment. In all cases, the prediction compared reasonably well with experimental results. Spray impingement model and fuel film formation model have been applied to a direct injection diesel engine combustion chamber.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.3
• /
• pp.183-191
• /
• 2016

A systematic development process for the low noise FEAD (Front End Accessory Drive) system is presented by combining CAE (Computer Aided Engineering) and the experimental rig test. In the estimation of the belt drive noise, two main difficulties arise from the high non-linearity due to the stick-slip contacts on the interfaces of the belt and pulleys, and the interaction of the belt drive system with the powertrain rotational parts. In this work, a recently developed analysis method of the belt drive has been employed considering powertrain rotational dynamics. As results, it shows good correlation with the vehicle tests in various operational modes. The established model has been employed to validate the new design improving the stick-slip noise of the problematic FEAD system. Furthermore, the best proposal of FEAD system in terms of functionality [NVH (Noise, Vibration and Harshness), fuel economy, cost. etc.] has been suggested in the concept design stage of new engine through this presented methodology.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.208.2-212
• /
• 1997

In a model based friction comensation for a frictional system,the performance of the system is inflenceed by the selection of the friction model. Especially, when a real plant have dynamic friction characteritics, the compensation of friction with a static friction model may deteriorate the perfomance. For the system we constlucted an adaptiv parameter estimation and friction compensation with a newly introduced dynamic friction model proposed by Canudas et.[1]. The model depicts varios frictional phenomena,such as Stibeck effect,frictional memory, Stick-slip motion. Parmeter identification algorithm are followed conventional RLSM adaptive rule. The stability for the closed system was proved by the Lyapunov stability. The result say that if a real system have dynamic friction property,the friction compensation with the dynamic friction model will improve the perfomance moreover static friction model based compensation may lead to the system unstable.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.211-216
• /
• 2003

A frontal offset impact model Oat can simulate the 40% offset frontal impact into deformable barrier regulated in EU Directive 96/79 EC has been developed. Engine rotation effects are also considered in the model. Distributed 11 masses and characteristics of 23 nonlinear springs comprising the model are determined based on both the stick-model analysis under the general specification of car and the dynamic characteristics of car structure. It is demonstrated that simulated acceleration-time curve for passenger part is in good agreement with test data obtained by NHTSA.

• 한국연소학회:학술대회논문집
• /
• 2012.04a
• /
• pp.283-286
• /
• 2012

The analytical model determining the unknown parameters of reaction rate equation which is necessary to simulate the combustion phenomena of energetic materials is proposed. The relationship between detonation velocity and size effect of energetic materials is derived from simplified JWL++ model. Theoretical model is used to investigate the combustion characteristics of certain energetic materials before running Hydrocode by pre-determination of unknown parameter, b. When b=0.8, the behavior of HANFO gunpowder is in the form of concave-up and ANFO explosives has the concave-down form in case of b=1.5. The analytical model provides efficient and highly accurate results rather than previous method which simulated the unconfined-rate-stick via the numerical means.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.731-742
• /
• 2010

Modeling of rubber for design or analysis often requires confusing or complex work because there are a large number of constitutive models to be considered. Some models have few material constants, while others have many. Researchers have to prepare and fit extensive experimental data with caution and discretion. In this paper, we first compared some typical rubber models in which deformation was carried out by stretching up to around eight times the original size. We conclude that continuum-based models and chain molecular models can be used in the study of the small deformation in most engineering applications, but chain molecular models are preferred in the study of the large deformations in most biomaterial applications. As discrimination problems, Treloar's patch and cylindrical balloon stick are tested theoretically and numerically for studying bifurcation. In the case of Treloar's patch, by using the Kearsley's equation, we show that bifurcation exists for continuum-based models but not for chain molecular models. Both models show bifurcation in the cylindrical balloon stick. Therefore, in the analysis of the bifurcation of rubber showed that its existence also depends on the constitutive model selected.

• Restorative Dentistry and Endodontics
• /
• v.35 no.4
• /
• pp.257-266
• /
• 2010

The purpose of this study was to determine the effect of post types and sizes on fracture resistance in immature tooth model with various restorative techniques. Bovine incisors were sectioned 8 mm above and 12 mm below the cementoenamel junction to simulate immature tooth model. To compare various post-and-core restorations, canals were restored with gutta-percha and resin core, or reinforced dentin wall with dual-cured resin composite, followed by placement of D.T. LIGHT-POST, ParaPost XT, and various sizes of EverStick Post individually. All of specimens were stored in the distilled water for 72 hours and underwent 6,000 thermal cycles. After simulation of periodontal ligament structure with polyether impression material, compressive load was applied at 45 degrees to the long axis of the specimen until fracture was occurred. Experimental groups reinforced with post and composite resin were shown significantly higher fracture strength than gutta-percha group without post placement (p < 0.05). Most specimens fractured limited to cervical third of roots. Post types did not influence on fracture resistance and fracture level significantly when cement space was filled with dual-cured resin composite. In addition, no statistically significant differences were seen between customized and standardized glass fiber posts, which cement spaces were filled with resin cement or composite resin individually. Therefore, root reinforcement procedures as above in immature teeth improved fracture resistance regardless of post types and sizes.

• Journal of the Korean Chemical Society
• /
• v.48 no.1
• /
• pp.77-84
• /
• 2004

The purpose of this study was to analyze the controversial points in the concepts of materials in the science textbook of middle school and to provide alternatives of teaching method. For this study, units in connected textbooks were analyzed and the teaching method using ball-and-stick models was developed. The subjects were 130 second graders from a middle school in Seoul, Korea. It aimed to compare the effectiveness of using ball-and-stick models for lesson with the one of traditional lessons, in learning concepts concerning materials by cognitive levels and to investigate the difference of scientific concept formation about concepts concerning materials by their cognitive levels between experimental group and control group by using concept formation questionnaires. Before the instructions, a short-version GALT was administered. After instructions, the posttest of concepts and attitude test connected with science subject were administered, and 10 months later, the posttest of concepts was administered to analyze the long-term memory effects. According to the results, the experimental group using the ball-and-stick models had significantly higher scores at conceptual understanding and long-term memory effects than the control group and improved the attitude relevant to science subject, and also had affirmative effects in attitude for science and science work. When analyzing the results according to the cognitive level, the long-term memory effects was high in the concrete operational stage students. From the results of this study, middle school students that are more concrete operational stage and transitional stage than formal operational stage elevates interesting in studying by using ball-and-stick models and making material form concretely. It would be effective in helping the students develope the correct concepts by connecting real world as materials and the particle world as atom.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.799-804
• /
• 2003

Friction phenomenon can be described as two parts which are pre-sliding and sliding regions. In motion of the sliding region, friction forces depend on the velocity of the system and are known as Coulomb, stick-slip, stribeck effect and viscous friction. The pre-sliding region, which is before breakaway, depends on the position of the system. The motion of friction in the sliding region can be described as the LuGre model. But the pre-sliding motion of friction, which has hysteresis characteristics in general, is not known widely. Therefore, an improved friction model, which can describe the motion of friction in the pre-sliding region, is proposed in this paper. And simulation and experimental results show the effectiveness of the proposed friction model for precise tracking control systems.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.163-170
• /
• 2002

The dynamic model of a high-speed vacuum circuit breaker mechanism with spring-actuated cam and linkage is derived to simulate the high-speed closing and opening operations. Its validation for an analysis of high-speed motion behavior is checked through experiments. The characteristics of the friction on the camshaft are investigated using the nonlinear pendulum experiment. The parameters of the friction model are estimated using the optimization technique. The analysis exhibits that the friction of the pendulum depends on stick-slip, Stribeck effect and viscous damping. Comparing simulation results with actual responses using a high-speed camera, the appropriateness of derived dynamic models for the rapid closing and opening operations is shown. The spring motion, which has much influence on the closing responses, is observed.