• 한국세라믹학회지
• /
• 제34권4호
• /
• pp.399-405
• /
• 1997

With the increase of ZnO content, heat of hydration decreased. For specimens containing ZnO more than 0.6 wt.%, the compressive stength of cement cured for 28 days could not be measured because setting was not occurred. With the increase of ZnO content, Blaine specific surface area of cement was decreased and the residue of 45 ${\mu}{\textrm}{m}$ and 90 ${\mu}{\textrm}{m}$ was increased when cement was ground. That is, grindability became worse as ZnO increased in clinker. The difference of color as a function of ZnO content could not be observed, but in the excess of amount of ZnO added, color became more white and reddish yellow.

• 대한치과의사협회지
• /
• 제11권1호
• /
• pp.41-44
• /
• 1973

The experiment consisted of cementing full veneer crown of extracted teeth and a standardized cylindrical metal dies (6mm diameter, 6mm height, 1mm shoulder) and then measuring the tensile strength required to remove the cemented restoratoins by the Instron testing machine in the Korea Institude of Science and Technology. The Instron machine was operated at a rate of loading of 0.2cm per minute. From the experiments, the following results obtained. 1. The tension of zinc phosphate and alumina EBA cements were highest all of the cements. 2. The tension of Fynal and the addition of eugenol to zinc Phosphate cements were similar. The addition of eugenol to zinc phosphate cement was half stength and Fynal cement was on third strength than zinc phosphate cement. 3. The tension of zinc oxide-eugenol cement was lowest all of the cements.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 가을 학술발표회 논문집
• /
• pp.119-123
• /
• 1995

This paper presents an accelerated-curing method by the war water method and discusses how these methods can be adapted for regular quality control and quality assurance of concret. Accelerated strength test data can be used for estimating the furture stength, e.g. the 28-day strength. An accelerated-curing method to predict the 28-day strength of concrete from 1-day warm water-cured test results was evaluated in the laboratory and the field. For these evaluations test are performed for 1845 standard specimens from 123 different batches of concrete. The results of this study the equation applicable universally with resonable accuracy are presented for estimating the potential strength of concrete by the warm water-curing method.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 가을 학술발표회 논문집
• /
• pp.267-272
• /
• 1995

The objective of this study is to investigate the effect of concrete strength on the stirrup effectiveness factor(K) of reinforced concrete beams with stirrup based on previous test results(a/d$\geq$2.5). In the procedure of the estimation of K, it was assumed that the ultimate shear strength for beams without stirrup is equal to the concrete contribution to shear strength for beam with stirrup. A model equation for calculation the stirrup of compressive strength of concrete. It was shown that the stirrup effective factor of compressive strength of concrete. It wah shown that the stirrup effective factor is greater than 1.0 up to compressive strength 85MPa. Therefore the current ACI Code equation for predicting the shear strength and the stirrup effectiveness factor of 1.0 is conservative for nomal and high stength concrete beams with stirrup.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1020-1024
• /
• 1997

Recently the use of ceramic materals has been greatly increased in the industries. But machining of the ceramics is quite unproductive because of their high stength,high hardness,and brittleness. The efficiency of the grinding operation of ceramics depends on the preparation of diamond grinding wheel, i.e.,truning and dressing. This paper describes some experimental results on the dressing conditions of diamond grinding wheel. The dressing performance is evaluated by the magnitude of normal grinding force. The better dressed wheels result in the lower normal grinding forces. The dressing performances of copper plate and aluminum oxide dressing stick are compared. The optimum dressing conditions including the grit size of dressing sticks, the depth of the dressing operation, and the dressing speed qre determined.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권2호
• /
• pp.36-46
• /
• 1995

In this paper, fatigue crack propagation behaviors were investigated experimentally for the materials, carbon steel forgings (SF45A, SF50A, SF60A) which are used in the marine propeller shaft. The results obtained are as follows: The number of cycles required to grow crack length 1.30mm from microcrack initiation was about 60% of the total fatigue life. Fatigue crack propagation rate was expressed by the equation d(2a)/dN_B 2a/$N_f$ and the result was agreed well with the experimented data. And the equation d(2a)/dN=$C{\sigma}_a^m(2a)^n$ was evaluated also. Obtained material property m and n are 3~5 and 1-1.5 respectably, and the result was reasonably agreed to the data obtained from experiments.

• 펄프종이기술
• /
• 제31권1호
• /
• pp.79-88
• /
• 1999

The stability and performance (peel strength) of the acrylic copolymer and various modified rosin systems were investigated. The peel strength was measured over a wide range of scaling rates, and the influence of the viscoelasticity of the PSA(pressure sensitive adhesive) was considered. In the case of miscible systems, the peak of peel strength (PSA performance) over wide peel rates was changed and modified systematically with increasing glass transition temperature of the blends. The peak of the peel strength for blended systems shifts toward the lower rate side as glass transition temperature ($T_g$) of the blend increased. The influence of esterification of the rosin on performance and stability against deterioration was greatly modified by blending with rosin of glycerol ester and rosin pentaerythritol ester. The failure mode of the blend varies with the combination with acrylic copolymer and modified rosin, and cohesive failure was found at a lower peel rate while interfacial failure was found at a high peel rate. A few systems where a single Tg could be measured, despite the fact that two phases were observed microscopically, were detected.

• 콘크리트학회논문집
• /
• 제12권5호
• /
• pp.131-139
• /
• 2000

Porous Concrete usually contains large amount of voids(about 10∼20%) after compaction so that it has relatively high permeability. It has been introduced in domestic since early 1980's but it has problems such as lack of optimized mixture, low strength and durability, and other defects, etc. The purpose of this study is to manufacture high-performance porous concrete using polymer to enhance the mechanical properties. The results of this study are as follows; the compressive strength range 12 92∼207kgf/㎠, the tensile strength range is 14∼28kgf/㎠, the bending stength range is 42∼73kgf/㎠, and the coefficient permeability range is 5.77×10-2∼6.79×10-1cm/sec. To develope high-performance porous concrete. further studies are needed on optimum mixture of fineness modulus and admixture.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.200-201
• /
• 2017

Generally, a lot of reinforcements are used in nuclear power plant concrete structures, and it may cause several potential problems when concrete is poured. Because of the congestion caused by hooked bars, embedded materials, and other reinforcements, it is too difficult to pour concrete into structural member joint area. The purpose of this study is to change ACI 349 Code for using the large-size(57mm) and high-strength(Gr.80) headed deformed bars instead of standard hooked bars in nuclear power plant concrete structures in order to solve the congestion problems.

• 한국표면공학회지
• /
• 제23권1호
• /
• pp.44-51
• /
• 1990

Effects of temperature on the tensile properties of annealed and hydirded Zircaloy-4 plate in which hydrides are precitated paralled to the rolling direction were investigated. The main results obtained are as follows : 1) In annealed Zircaloy-4, yield point phenomenon was found in the temperature range of $200-550^{\circ}C$, while in hydrided alloy the phenomenon was found in the range of $200-400^{\circ}C$. 2) The dynamic strain aging behavior was occurd in the temperature interval of 400-$550^{\circ}C$in both annealed and hydrided Zircaloy-4. 3) The nearly values of yield strength, tensile stength and elongation are obtained in both annealed and hydried Zircaloy-4. From this result, we are led to conclude that the hydrides which are preiptated parallel to the circumferenial direction of nucler fuel are not so harmful for tensile properties of the clad.