• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.387-392
• /
• 2001

Kobe Steel, LTD. and Midrex Technologies Inc. jointly developed the FASTMET$\circledR$ process as a steel mill waste recycle technology in which the DRI product meets BF feed material or BOF/EAF feed material requirements. FASTMET(R) process turns value-less wastes into valuable DRI and sellable zinc oxide, and gives the solution for the steel mill wastes recycling from both economical and environmental viewpoints. During the development of the process, Laboratory, Pilot Plant and Demonstration Plant tests were carried out from 1990 to 1998. The first FASTMET(R) commercial plant began operation in April, 2000 and the second commercial plant started in April, 2001 Both commercial plants have proceeded successfully preying that FASTMET$\circledR$ is a suitable process for recycling steel mill waste and for producing DRI as an iron source.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1323-1326
• /
• 2003

In this paper, we propose set-up model of silicon steel cold rolling mill. Until now, the working of Silicon Steel is operated using the look-up table value of roll force which a field operator finds by making good use of his experience. Therefore, the standardization of data and an improvement of the quality on product are very difficult. So we establish neural model using field data of various kinds of coil at each pass.

• Resources Recycling
• /
• v.22 no.1
• /
• pp.36-41
• /
• 2013

LF slag is formed by EAF carryover slag and slag former(such as lime, dolomite) put into the ladle during the tapping molten metal. After LF process, continuous casting is started when molten steel is sent from ladle to tundish through bottom nozzle of ladle. Conventionally, remained molten slag and steel in ladle are poured into a slag port and they are transferred to a slag yard and then recycled. In this study, we investigated about recycling of molten LF slag residue(including Fe residue to reuse) which is made in steelmaking process. As a result, lime usage was decreased about 2.2~3.2 kg/steel-ton and also molten steel yield rate was increased about 0.3 ~ 0.5 percent point.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.6
• /
• pp.753-760
• /
• 2007

For protection of the cylinder wall of the ball mill for grinding raw ore. the inner side of the cylinder is covered with rubber liner. The rubber is easily worn down because the rubber relatively soft compared with raw ore. So the rubber liner in the ball mill cylinder must be replaced almost every year and the cost for replacing rubber liner formidable. In this paper, for reducing or excluding the cost of replacing rubber liner the basalt liner is designed. The basalt materials are generally harder than raw ore and the basalt liner in the ball mill does not wear down and so it can be used almost permanently. The concave surfaces are made on the liner of the ball mill and the liner in the cylinder wall plays also the role of raising the steel balls mixed in the raw ore. The section profiles of the concave surface have an important effect on the performance of the ball mill. The deep concave grooves raise the steel balls to high levels and give the large potential energy to the steel balls impacting to the raw ore. But if the concave grooves are too deep. the steel balls raised too high by the concave grooves fly along the parabolic path and reach to the other side of cylinder wall and so the steel balls do not play the roles of grinding the raw ore. The forces acting to a steel ball in a concave groove of the cylinder liner are also analyzed in this paper. The formulas calculating the height and the impact point of the steel ball are introduced and presented. Based to these formulas, the optimum section profiles of the basalt liner are presented.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1998.11a
• /
• pp.240-244
• /
• 1998

This study was carried out to investigate the efficiency of steel mill slag and sludge in removing heavy metals and cyanide in metal plating wastewater. Laboratory experiments were peformed with jar tester, The tests were peformed at ambient temperature. The results of tests showed that overall rates metals removed were greater than 90 %. Metals were removed from solution as the combined effects of adsorption and precipitation in alkaline condition. The removal efficiency of cyanide by steel mill wastes was above 90 % at optimum conditions. In view of the test results and other engineering characteristics of steel mill slag and sludge, these industrial by-products from steel industry have a high potential to be used in metal plating wastewater treament and were particularly beneficial.

• Journal of Information Technology Services
• /
• v.12 no.4
• /
• pp.255-265
• /
• 2013

This paper proposes a DEA-AR model for the efficiency evaluation of the iron ore brands in an integrated steel mill. The input factor is defined as unit cost of each brand based on CIF and two output factors are chosen as Fe and Al which are the important ingredients of iron ore. The relative importance between two output factors is determined by several experts using AHP model. The efficiency of each brand is determined using DEA and DEA-AR models. The negative correlation between the DEA-AR efficiency and the unit cost (CIF) is shown as significant whereas no significant correlation exist between the efficiency and the output factors. Also, the Kruskal Wallis rank sum test shows that there exist efficiency differences among the iron ore types whereas no difference is shown among the countries. The result could be utilized in selecting good brands of iron ores based on the DEA-AR efficiency in an integrated steel mill.

• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.66-71
• /
• 2000

The present study tackles the metallurgical subjects involving the thin slab-direct hot rolling process, i.e. mini-mill process. In order to clarify the effect of chemical composition of steel and MnS precipitation behaviors on the development of edge cracking during hot rolling, the content of manganese and sulfur in low carbon steel was varied and the isothermal treatment prior to roughing was applied. Edge cracking during roughing in the hot-rolling process of mini-mill was effectively prevented by means of the isothermal treatment at 115$0^{\circ}C$ for 5 minutes in the 0.4% manganese steel containing sulfur lower than 0.013%. With the increase in manganese content in low carbon steel, coarser MnS developed. The edge cracking index which denotes the total length of edge crack per unit edge-length of rolled specimens was proposed in this paper. It was found that the edge cracking index linearly decreased with the increase in the ratio of MnS.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.111-113
• /
• 2007

The Mechanical properties of steel in hot strip mill were associated with the alloy composition, plastic deformation, cooling history and so on. In the case of the same alloy composition and deformation conditions, cooling history on ROT (run out table) is the main factor in affecting mechanical properties of steel, especially, in carbon steel. On ROT, the steel undergoes under various kinds of cooling conditions such as radiation, convection by air, water and wetting zone. The coiling temperature (CT) of the steel is also important factor in affecting mechanical properties. But with the same CT, the mechanical properties of steel can be different because the temperature history of cooling is more important factor than CT itself. In this study, we have studied the relations between temperature history and mechanical properties of steel and then the predicted mechanical properties have compared with the measured values.

• Transactions of Materials Processing
• /
• v.6 no.2
• /
• pp.95-101
• /
• 1997

The thermal fatigue and wear properties of high speed steel roll which was recently developed were investigated by observing microstructure, by measuring mechanical and physical properties, by conducting thermal fatigue testing, and by measuring the amount of wear in actual mill. High speed steel roll had better thermal fatigue testing, and by measuring the amount of wear in actual mill. High speed steel roll had better thermal fatigue life than high chromium iron roll, which was due to lower carbide content, higher strength, and higher thermal conductivity. The amount of wear of high speed steel roll was nearly the same as that of high chromium iron roll in the first finishing stand, which was due to the oxide formation on the roll surface. However, in the third finishing stand, the wear resistance of high speed steel roll was 2~3 times as good as that of high chromium iron roll because the former had higher hardness at high temperature.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.03a
• /
• pp.101-109
• /
• 1996

Mini-mill process which is one of the new steel -marking technologies to be able to produce the hot rolled coils by thin slab caster of ISP(In-Line Strip Production) type, will be completed in the Kwangyang Steel Works of POSCO in August, 1996, SEt-Up Model of finishing mill which consists of 5 stands is the most basic and essential in mini-mill plant. Therefore, the simulation program of Finishing-mill Set-Up model were developed in this research , using new temeprature prediction model, roll gap model and rolling physical model. Using the developed FSU program , pass schedules to produce the strips with target strip thickness of 1.8mm, 2.0mm, 2.3mm, 2.7mm an d3.0mm were also determined respectively.