• 한국주조공학회지
• /
• 제25권3호
• /
• pp.134-141
• /
• 2005

To overcome the undesirable deformation, peeling off and geometrical restrictions which were mainly caused by differences in thermal expansion coefficients during the cladding of aluminum strip and stainless strip, new processing method based on vacuum die casting is designed and implemented in fabricating Al/Fe-17wt%Cr steel(stainless steel). To increase cast-bonding ability, the surface of Fe-17wt%Cr steel is electrochemically etched to have optimum pit size and density. The optimum conditions to generate best pit are as follows: Solution: 1 M $Fecl_{3}$+1 M Nacl, Addition: $CuCl_{2}+HCl$, Current density: 80 $mA/cm^{2}$, Total current: 400 $coulomb/cm^{2}$, AC frequency :60 Hz.

• 한국주조공학회지
• /
• 제43권3호
• /
• pp.107-136
• /
• 2023

주강품 사형주조에는 천연규사가 보편적으로 사용되었고, 규사의 열적특성 부족에 의한 소착결함 억제를 위해, 크로마이트사가 사용되기도 하였으나, 반복 사용에 의한 골재 열화, 시스템샌드 혼입 문제, 분리 제거의 어려움, 높은 밀도에 따른 조형 시 하중증가, 크롬 함유 폐기물이 되는 단점이 있다. 최근에는 주조업계의 중요한 과제로써 산업폐기물 저감 및 대기환경 개선이 부각되고 있다. 종래의 주물사 사용 시 발생되는 문제점 해결과 주조공장의 환경개선을 위해서, 천연사를 대체 적용할 수 있는 다양한 인공사가 개발되어 소개되고 있다. 인공사는 용융분사법으로 제조된 인공사와 조립소결법으로 제조된 인공사 및 분쇄법으로 제조된 인공사로 분류할 수 있으며, 원료광물의 종류, 제조공법에 따라 상이한 물리적 특성을 나타낸다. 본 연구에서는 각종 주물사의 물성, 주형강도, 물리적 내구성, 열적 내구성, 소착시험편 주조 등의 비교 평가시험을 하였다. 밀도에 따른 주물사 실사용량, 주물사 형상에 따른 주형강도, 주물사의 물리적 및 열적 내구성, 주물사의 내열특성을 종합적으로 고려하였을 때, 아크용사법으로 제조된 용융인공사 A1 또는 분말식화염용사법으로 제조된 용융인공사 B가 대형주강품 주조에 가장 적합한 구형의 인공사로 판단된다.

• 한국주조공학회지
• /
• 제17권2호
• /
• pp.135-144
• /
• 1997

The relative machinability of the invar-type cast alloys, such as invar cast steel, invar-type cast iron, Meehanite cast iron, and the modified Invar-type cast iron containing Mo and V was evaluated based on the tool life test, the surface roughness test and the chipping test. Tool life and surface roughness were measured under various cutting conditions. The tool lives of Invar cast steel, Meehanite cast iron, the modified Invar cast iron and Invar cast iron was 12 min, 8 min, 1 min, 41 min, respectively. The surface finish of Invar cast steel and the modified Invar cast iron was better than that of Meehanite cast non, and the chip breakability of invar cast iron and Meehanite cast iron was better than that of invar cast steel. The Taylor's equations of invar cast steel and the modified invar cast iron were $VT^{0.3076}=154.479$ and $VT^{0.3880}=102.326$, respectively. As the cutting speed increases, the surface finish of the modified invar cast iron was improved.

• 한국주조공학회지
• /
• 제5권4호
• /
• pp.271-282
• /
• 1985

In order to investigate the mold reaction characteristics of Mn steel and Cr steel castings individually, the mold reaction products were examined by scanning electron microscopy, electron prove microanalyzer and X-ray diffractometer. From this experiment, the results were summarized as follows: 1) The mold reaction depth increased with increase of Mn content, while it decreased with increase of Cr content. 2) Mold reaction depth decreased with Mn content at $1200^{\circ}C$. 3) Mn, among the reaction products, forms a low fusion silicate, Mn $O.SiO_2$ while Cr forms a stable oxide, $CrO_3$ which hindering the reaction between FeO and $SiO_2$ thus the formation of $FeO.SiO_2$ was depressed.

• 한국주조공학회지
• /
• 제35권2호
• /
• pp.23-28
• /
• 2015

This work presents the effect of the cooling rate on the precipitation of super duplex stainless steel. Specimens of super duplex stainless steel with a specific composition were cooled at various cooling rates after being melted at $1550^{\circ}C$ in a directional solidification furnace. Ferrite (${\delta}$), Austenite (${\gamma}$), Sigma (${\sigma}$), and Chi (${\chi}$) phases were precipitated when the cooling rate was lower than 0.22 K/s. When the cooling rate was 0.22 K/s or faster, ${\sigma}$ and ${\chi}$ phases were not precipitated.

• 한국주조공학회지
• /
• 제21권5호
• /
• pp.296-303
• /
• 2001

The effects of the revolution speed on the mechanical properties and microstructure of Cr-Mo steel during vertical centrifugal casting using investment mold were investigated. The casting yield, tensile strength, hardness and absorbed energy during impact test were increased with increasing revolution speed. The effect of mass variation caused by the change in the revolution speed on the grain size was the most significant.

• 한국주조공학회지
• /
• 제30권4호
• /
• pp.151-156
• /
• 2010

The high-strength low-alloy (HSLA) steels have low carbon contents (0.05~0.25% C) in order to produce adequate formability and weldability, and they have manganese contents up to 1.7%. Small quantities of silicon, chromium, nickel, copper, aluminum, molybdenum are used in various combinations. The results contained in this paper can provide the valuable information on the development of $-40^{\circ}C$ low temperature HSLA. Furthermore, the present experimental data will provide important database for casting steel materials of the offshore structure.

• 한국주조공학회지
• /
• 제40권5호
• /
• pp.129-133
• /
• 2020

The outcomes of solution annealing and stress corrosion cracking in cold-worked 316L austenitic stainless steel have been studied using x-ray diffraction (XRD) and the slow strain rate test (SSRT) technique. The good compatibility with a high-temperature water environment allows 316L austenitic stainless steel to be widely adopted as an internal structural material in light water reactors. However, stress corrosion cracking (SCC) has recently been highlighted in the stainless steels used in commercial pressurized water reactor (PWR) plants. In this paper, SCC and inter granular cracking (IGC) are discussed on the basis of solution annealing in a chloride environment. It was found that the martensitic contents of cold-worked 316L stainless steel decreased as the solution annealing time was increased at a high temperature. Moreover, mode of SCC was closely related to use of a chloride environment. The results here provide evidence of the vital role of a chloride environment during the SCC of cold-worked 316L.

• 한국주조공학회지
• /
• 제30권2호
• /
• pp.55-59
• /
• 2010

• 한국주조공학회지
• /
• 제25권1호
• /
• pp.10-15
• /
• 2005