• Journal of Welding and Joining
• /
• 제21권2호
• /
• pp.3-8
• /
• 2003

• 한국기계가공학회지
• /
• 제13권3호
• /
• pp.77-82
• /
• 2014

In this study, we carried out the interrupted cutting of carbon steel for a machine structure (SM45C) with a CVD-coated tool and conducted an ANOVA test and a confidence interval analysis to find factors influence the surface roughness and to obtain a regression equation. We found that factor which mostly affects the surface roughness during interrupted cutting was the feed rate. The cutting speed and depth of the cut only had small effect on the surface roughness. From the result of a multi-regression analysis during an interrupted cutting experiment, we obtained regression equation. Its coefficient of determination was 0.918, indicating that the regression equation was predictable. Compared to continuous cutting, if the feed rate increases, the surface roughness will also increase during interrupted cutting.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 금형가공 심포지엄
• /
• pp.11-18
• /
• 2002

The STD11 and KP4 are important steels and applied to the manufacturing of the die and mold. The purpose of this study is to investigate the machinability of tool steels of STD11(HRC60) and KP4(HRC32) when machining them by using ball end milling tools coated with TiAlN. Cutting forces by using a Kistler piezo-cell type tool dynamometer, surface roughness and tool wear by using tool microscope are used in the tests. The results from the cutting tests of KP4 specimens show that 85m/min. of cutting speed and 0.32mm/rev. of feed per revolution are optimum conditions for the higher productivity and 0.26mm/rev. with the same cutting speed are optimum conditions for better surface finishing. The results from machining STD11 workpiece at 30m/min. of cutting speed and 0.17m/rev. of feed per revolution show recommended for the higher productivity. The KP4 shows relatively smaller cutting forces than STD11 and STD11 shows the better surface finish than KP4.

• Structural Engineering and Mechanics
• /
• 제59권5호
• /
• pp.933-950
• /
• 2016

Decks, interior beams, edge beams and girders are the parts of a steel floor system. If the deck is optimized without considering beam optimization, finding best result is simple. However, a deck with higher cost may increase the composite action of the beams and decrease the beam cost reducing the total cost. Also different number of floor divisions can improve the total floor cost. Increasing beam capacity by using castellated beams is other efficient method to save the costs. In this study, floor optimization is performed and these three issues are discussed. Floor division number and deck sections are some of the variables. Also for each beam, profile section of the beam, beam cutting depth, cutting angle, spacing between holes and number of filled holes at the ends of castellated beams are other variables. Constraints include the application of stress, stability, deflection and vibration limitations according to the load and resistance factor (LRFD) design. Objective function is the total cost of the floor consisting of the steel profile cost, cutting and welding cost, concrete cost, steel deck cost, shear stud cost and construction costs. Optimization is performed by enhanced colliding body optimization (ECBO), Results show that using castellated beams, selecting a deck with higher price and considering different number of floor divisions can decrease the total cost of the floor.

• 산업기술연구
• /
• 제24권B호
• /
• pp.19-29
• /
• 2004

The demand for demolition of steel structures is recently increasing in Korea. Most of flexible linear-shaped charges(FLSC) for steel demolition are now imported from foreign countries. Some basic experiments have been studied to determine the optimum parameters of design for domestic development of FLSC. Domestic FLSC were used to check cutting of steel structures and other materials in this study. The result shows that domestic FLSC is very effective to cut steel structures.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.198-203
• /
• 1999

In this study, chip-tool friction and shear characteristics of cold drawn free machining steels in turning were assessed. To do this, a newly developed equivalent oblique cutting model was adopted. And for comparison with those of free machining steels, chip-tool friction and shear characteristics of conventional carbon steels were also investigated. The Pb-S free machining steel shows superior machinability to others. In case of the Bi-S free machining steel, the shear stress and the specific friction energy are relatively lower than those of conventional carbon steels, but its shear strain is relatively high, so it does not show any remarkable improvement of machinability.

• 한국정밀공학회지
• /
• 제15권8호
• /
• pp.33-38
• /
• 1998

TiYN coated high speed steel tools have been developed and their tool lifes were assessed. First yttrium alloyed titanium target was manufactured, then using the arc ion plating(AIP) technique TiYN coating was deposited onto high speed steel substrate. Three kinds of varying thickness of TiYN coated tools were prepared. Cutting tests were carried out with theses tools and for comparison with the commercially available uncoated, TiN, TiCN and TiAlN coated tools. During the cutting tests flank wear width vs. cutting time was measured. It has been revealed that the newly developed TiYN coated tools show superior tool life characteristics to others.

• 한국구조물진단유지관리공학회 논문집
• /
• 제14권6호
• /
• pp.220-228
• /
• 2010

일체형 삼각 트러스 형태의 철선을 아연도금 강판에 용접한 철선일체형 데크 플레이트는 슬래브 시공 시 현장시공 최소 및 동바리와 지보공 등 거푸집 공사비 절감을 목적으로 개발되어 이미 많은 현장에 적용되고 있다. 본 연구에서는 철선일체형 데크 플레이트 시스템의 구조성능 평가를 위해 상부철선, 하부철선, 래티스 철선, 경간, 단부가공방법을 변수로 채택하여 총 32개의 시험체를 실물크기로 제작하여 실험적 연구를 수행하였다. 연구결과 시험체의 최종파괴형태 변화 및 단부가공방법이 시험체의 구조 성능에 영향을 미치지 않는 것으로 나타났으며, 경간 3.2m 시험체는 래티스 철선으로 ${\Phi}4.5$를 사용해도 큰 무리가 없는 것으로 나타났다.

• 한국기계가공학회지
• /
• 제16권6호
• /
• pp.7-14
• /
• 2017

This study manufactured a minimum quantity lubrication (MQL) supply system and identified the optimal MQL machining cutting conditions for plastic mold steel (SCM440). A series of experiments were consisted of twice. Optimal cutting conditions were derived using the Taguchi method, and cutting force variance; surface roughness; tool wear; and cutting temperature in dry, wet, and MQL machining were measured experimentally for these optimal conditions. The measured results decreased from dry to wet and MQL machining, being particularly large for dry machining due to increased cutting time. Measured MQL machining metrics were similar to those for wet machining, particularly for surface roughness, which is an index of machining quality.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.951-954
• /
• 2000

This paper presents a new cutting method, i.e. diamond cutting, aided by electrolysis, in order to cut ferrous materials with diamond tools. Diamond cutting is widely applied in manufacturing ultraprecision parts such as magnetic disk, polygon mirror, spherical/non-spherical mirror and copier drum, etc. because of the diamond tool edge sharpness. In general, however, diamond cutting cannot be applied to cutting steels, because diamond tools wear excessively in cutting iron based materials like steel due to their high chemical interaction with iron in high temperature. In order to suppress the diffusion of carbon from the diamond tool and to reduce increase of cutting force due to size effect, we attempt to change chemically the compositions of iron based materials using electrolysis in a limited part which will be soon cut. Through experiments under several micro-machining and electrolysis conditions, cutting using electrolysis, compared to conventional cutting, was found to result in a great decrease of the cutting force, a better surface and much less wear tool.