• 복합신소재구조학회 논문집
• /
• 제4권3호
• /
• pp.30-37
• /
• 2013

It is same such as the provision of shear buckling strength of steel composite box girder web panel and plate girder web panel in Korea Highway Bridge Design Standards(2012). But the web panel of steel composite box girder is different from the web of plate girder in that the upper slab and lower flange are connected to the web. So a different shear behavior of the girders is expected. In this study, To calculate a reasonable elastic shear buckling strength of steel composite box girder web panel, ABAQUS program was used. The results from F.E.A and previous studies are compared. It is shown that the web shear buckling strength of steel composite box girder of Korea Highway Bridge Design Standards(2012) is the most conservative.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권6호
• /
• pp.50-60
• /
• 2013

본 연구에서는 교량의 노면조도 및 교량과 차량 사이의 상호작용을 고려한 수치해석방법을 사용하여 도로교설계기준에 규정된 표준트럭 하중인 KL-510에 의한 강판형교의 동적응답을 연구하였다. 대상교량은 건설부에서 제정한 "도로교 상부구조 표준도"에 수록되어 있는 지간이 20m, 30m와 40m인 단순 강판형교를 사용하고. "보통의 도로"에 대하여 생성시킨 10개의 노면조도를 사용하였다. 차량은 5축 트랙터-트레일러인 표준트럭하중 KL-510을 3차원 차량으로 모델링하고, 교량은 주형을 보요소로, 콘크리트 바닥판은 쉘요소로, 주형과 콘크리트 바닥판 사이는 Rigid Link를 사용하여 3차원으로 모델링하였다. 이와 같은 노면조도 및 차량을 사용하여 강판형교의 충격계수와 DLA를 구하고 각국의 설계기준과 비교 검토하였다.

• 대한토목학회논문집
• /
• 제28권1A호
• /
• pp.39-49
• /
• 2008

본 연구에서는 교량의 노면조도 및 교량과 차량 사이의 상호작용을 고려한 수치해석방법을 사용하여 여러 매개변수에 대한 강판형교의 동적응답을 연구하였다. 대상교량은 건설교통부에서 제정한 "도로교 상부구조 표준도"에 수록되어 있는 지간이 20 m, 30 m와 40 m인 단순 강판형교를 사용하고, 여러 종류의 도로에 대하여 생성시킨 노면조도를 사용하였다. 차량은 2축과 3축 덤프트럭 및 5축 트랙터-트레일러인 표준트럭(DB-24)을 3차원으로 모델링하고, 교량은 주형을 보요소로, 콘크리트 바닥판은 쉘요소로 이상화시켰으며 주형과 콘크리트 바닥판 사이는 Rigid Link를 사용하여 3차원으로 모델링하였다. 이와 같은 차량 및 노면조도를 사용하여 강판형교의 지간별, 통행 차종별 및 노면조도별 충격계수와 DLA를 구하고 각국의 설계기준과 비교 검토하였다.

• Steel and Composite Structures
• /
• 제45권1호
• /
• pp.119-131
• /
• 2022

Due to the complexity of the structure and the limits of classical SEA, a combined SEA approach is employed, with angle-dependent SEA in the low- and mid-frequency ranges and advanced SEA (ASEA) considering indirect coupling in the high-frequency range. As an important component of the steel box girder, the dynamic response of an L-junction periodic ribbed plate is calculated first by the combined SEA and validated by the impact hammer test and finite element method (FEM). Results show that the indirect coupling due to the periodicity of stiffened plate is significant at high frequencies and may cause the error to reach 38.4 dB. Hence, the incident bending wave angle cannot be ignored in comparison to classical SEA. The combined SEA is then extended to investigate the vibration properties of the steel box girder. The bending wave transmission study is likewise carried out to gain further physical insight into indirect coupling. By comparison with FEM and classical SEA, this approach yields good accuracy for calculating the dynamic responses of the steel box girder made of periodic ribbed plates in a wide frequency range. Furthermore, the influences of some important parameters are discussed, and suggestions for vibration and noise control are provided.

• 한국구조물진단유지관리공학회 논문집
• /
• 제2권1호
• /
• pp.89-97
• /
• 1998

This paper presents the results of the load test performed on a steel plate girder bridge and suggests the procedure of bridge rating through the load test. In general the girder bridge resist the loads as a complex three-dimensional structural system. Therefore the test results are analyzed for the longitudinal and the transverse response characteristics. The bending moments based on the beam analysis are compared with the measured values for longitudinal response characteristics. The lateral load distribution characteristics are assessed based on the load test results for transverse response characteristics. Also the rating of the test bridge is performed by using the suggested rating procedure which considers the actual response characteristics of the bridge. The suggested procedure can be used for understanding of actual response characteristics and evaluating load carrying capacity of the steel plate girder bridge.

• 한국강구조학회 논문집
• /
• 제16권3호통권70호
• /
• pp.325-332
• /
• 2004

강합성거더 교량의 단면은 강거더와 콘크리트 슬래브의 합성정도에 따라 각각 비합성, 부분합성 그리고 완전합성 단면들로 구분 할 수 있다. 국내의 경우 강합성거더 교량의 단면을 합성시키기 위하여 일반적으로 전단 연결재 중 스터드를 사용하도록 규정하고 있고, 진단 연결재가 없는 경우 즉 비합성 단면의 경우에는 바닥판 앵커를 설치하도록 경험적으로 규정하고 있다. 그러나 바닥판 앵커를 사용한 단면의 실제 거동은 비합성 거동이 아닌 부분합성의 거동을 나타낸다. 그러한 이유로 본 연구에서는 바닥판 앵커를 사용한 플레이트거더교의 부분합성에 관한 해석 및 실험연구를 수행하였다. 실험연구를 통해서 바닥판 앵커의 초기강성을 산정하였고, 해석연구를 통해서 바닥판 앵커를 사용한 단순 및 2경간 연속 플레이트거더교의 합성정도를 비교$\cdot$분석하였다. 또한, 실험에 의해 산정된 강성 값에 근거하여, 2경간 연속 플레이트거더교에 바닥판 앵커를 적용하였을 때 발생할 수 있는 내부지점부 콘크리트의 인장응력 저감 효과를 검토하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.1326-1331
• /
• 2006

The precast concrete deck is one of suitable solutions for replacement and new construction in urban area. However, the precast concrete deck could be a weak point of the steel plate girder bridges structurally due to the connections between precast panels in the longitudinal direction. Thereafter, it is necessary for improvement of durability and load carrying capacity to introduce the prestress force in the longitudinal direction Some cracks of connections at the precast concrete deck may be occurred due to live loads, the difference of temperature and long-term effects. The shrinkage and creep of concrete may significantly affect long-term behaviors which occur tensile stresses at the precast concrete deck of steel plate girder bridges. In this study, the time-dependant analysis program has been developed to determine the initial prestress force in the longitudinal direction considering loss of stress at the precast concrete deck. Also it has been estimated the initial prestress force by construction stages and shapes of girder.

• 한국철도학회논문집
• /
• 제9권2호
• /
• pp.151-159
• /
• 2006

It analyzed the mechanical behaviors of non-ballasted railway bridge (steel plate girder type) with ballast reinforced on the finite element analysis, field test and laboratory test far the static and dynamic responses. The major objective of this study is to investigate the effects and application of reinforcement for steel plate girder railway bridge by the external post-tensioning method. The reinforcement of non-ballast railway bridge had obviously stable dynamic behaviors due to the additional dead force which was ballast. But in case of static behaviors, static displacements and stresses had increased nearly the allowable values. Therefore we analyzed the mechanical behaviors of non-ballasted railway bridge with ballast reinforced and external post-tensioning reinforced on the finite element analysis and laboratory test for the static and dynamic behavior. As a result, the reinforcement of ballasted railway bridge the external post-tensioning method are obviously effective for the additional dead force which is ballast. The analytical and experimental study are carried out to investigate the post-tension force decrease bending behavior and deflection in composite bridge for serviceability. The servicing railway bridge with ballast reinforced has need of the reasonable reinforcement measures which could be reducing the effect of additional dead load that degradation phenomenon of structure by an unusual. stresses and a drop durability.

• 한국해양공학회지
• /
• 제17권6호
• /
• pp.58-64
• /
• 2003

The performance of vibration-based damage detection methods is dependent upon the accuracy of modal parameters measured from structures of interest. Vibration monitoring, performed on a structure under uncertain temperature conditions, results in the uncertainty in model parameters of the structure. In this study, an experiment on the effect of various temperatures on modal characteristics of steel plate-girders is presented. First, the model plate-girder used for the experiment is described. Second, natural frequencies measured from the structure, using two different excitation sources, are described. Third, natural frequencies measured from the structure, under various temperatures, are described. Finally, the relationship between measurement temperature and natural frequency is analyzed.

• 한국철도학회논문집
• /
• 제8권1호
• /
• pp.41-50
• /
• 2005

Steel -Concrete Composite two girder railway bridges applying high performance steel with extra thick plate have economic and aesthetic advantages due to the simplification of manufacturing and construction process. However, steel bridges are seldom adopted in domestic railway bridge, since steel bridges are not efficient as R.C bridges considering dynamic characteristics and noise, etc. While highway bridges do not have lower horizontal bracing and larger interval of diaphragm cross beam, railway bridges install lower horizontal bracings to control the torsion due to heavy eccentrical line load. Accurate finite element analysis were performed with the parameters of existence of bracing and bracing shape, with the cross beam interval and stiffness, etc. To find out the effects of secondary members such as horizontal bracings and diaphragms, static md dynamic analysis have been performed by using finite element method. In this study, few member plate-girder bridges are analyzed with variable span lengths to examine the dynamic behavior and limits of damping. And though lateral bracings are members against torsion, but lateral bracing's absence is no big problem. Time history analysis using mode superposition method makes proof of this result.