• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1223-1231
• /
• 2018

The direct torque control (DTC) scheme features a simple structure thanks to stator flux-oriented control. It has the advantage of robustness against motor parameters variation since only the stator resistance is involved in the control scheme. On the other hand, the disadvantage of DTC is large torque ripple. To reduce the torque ripple, many studies on DTC-space vector modulation (DTC-SVM) schemes, which modulate the duty ratio with a fixed switching cycle, have been proposed. However, there is the difficulty in obtaining the duty ratio for DTC-SVM. Hence, this paper proposes a new duty ratio selection and stator flux calculation methods for reducing torque ripple. Simulations and experiments were carried out to determine the validity of the proposed method. The proposed scheme has simplified the duty ratio command and achieved the same control performance as the conventional duty ratio modulation method without using the information of motor parameters.

• 대한전기학회논문지
• /
• 제40권7호
• /
• pp.643-655
• /
• 1991

The analysis method on air gap permeance distribution, air gap MMF distribution, air gap flux density distribution, cogging torque and BEMF about the skewed stator slots or the skewed rotor magnet segments for BLDCM, respectively, is studied as a function of the skew ratio. The proposed method describes the differences between the skewed stator slots and teh skewed rotor magnet segments for the air gap permeance distribution, air gap MMF distribution and air gap flux density distribution. The reliability of the method is also confirmed by the waveform of the cogging torque and BEMF through experiments. And the result shows that the effects on the cogging torque and BEMF due to the skewed stator slots or the skewed rotor magnet segments are the same. In case of the skewed stator slots, the effects of the variations of the winding resistance and inductance are also studied.

• 전기학회논문지
• /
• 제66권11호
• /
• pp.1584-1590
• /
• 2017

This paper presents a implementation method of reliable speed limitation controller considering motor parameter variation in high speed operation. In spinning process of drum washing machine, speed increase has to be limited when unallowable imbalance mass is detected. Otherwise, severe noise and vibration can happen because noise and vibration are proportional to imbalance mass. To detect imbalance mass, d-axis current magnitude is used. However, we have to compensate for back-emf and power supply variation by means of detecting them because d-axis current is affected by both of them. On the other hand, we have to carefully estimate back-emf because back-emf is affected by stator resistance variation and inverter voltage error. Stator resistance variation can happen by manufacturing process for mass production or temperature variation in running. And there are inverter voltage errors between command voltage from micro-computer to inverter and real voltage from inverter to motor because of rising and falling time delay and turn-on resistance of power semiconductor switch. To solve this problem, we propose 2-step align current injection method which is to inject step-wise current right before starting. By this method, we can simply obtain stator resistance by ratio of voltage without inverter voltage error and current, and we can measure inverter voltage error. So we can obtain more exact model current, and then by simple calculation with compensation gain, we can estimate more accurate motor back-emf. We show that this method works well. It is verified through experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.106-109
• /
• 1995

This paper presents a new saturation modeling technique of synchronous generators using the operating data. With the stator voltages, currents and the field current directly measured on the field winding at different steady state operating conditions, it can estimate tile saturated stator mutual inductances, stator resistance and the field-stator equivalent turns ratio. Effects of the measurement noises on tile estimated parameters are also investigated.

• Journal of Power Electronics
• /
• 제13권2호
• /
• pp.250-255
• /
• 2013

This paper proposes an optimal current distribution method of dual-rotor brushless DC machines (DR-BLDCMs) which have inner and outer surface-mounted permanent-magnet rotors. The DR-BLDCM has high power density and high torque density compare to the conventional single rotor BLDCM. To drive the DR-BLDCM, dual 3-phase PWM inverters are required to excite the currents of a dual stator of the DR-BLDCM and an optimal current distribution algorithm is also needed to enhance the system efficiency. In this paper, the copper loss and the switching loss of a DR-BLDCM drive system are analyzed according to the motor parameters and the switching frequency. Moreover, the optimal current distribution method is proposed to minimize the total electrical loss. The validity of the proposed method was verified through several experiments.

• 한국전기전자재료학회논문지
• /
• 제21권12호
• /
• pp.1124-1129
• /
• 2008

The object of this paper is to acquire the data related to insulation evaluation of hybrid vehicle traction motors. We made a comparative analysis on Insulation Resistance (IR), Dielectric Absorption Ratio (DAR), and Polarization Index (PI) of the motor stators. The experiment was carried out according to IEEE Std. 43 and IEC 60085-1 for insulation resistance test standard of rotating machinery. Test voltage of 500 V was applied between a phase and the enclosure. The IR and the DAR of used motors were lower than those of new ones. The DAR and the PI were $0.92{\sim}1.02$ and $0.74{\sim}1.1$, respectively and the result did not meet the recommendation basis 2 for insulation level H. From the experimental results, we could prepare parameters and basis for insulation evaluation of the traction motor stator by the comparative analysis of short-time insulation resistance changes, DAR and PI.

• 전기학회논문지
• /
• 제57권9호
• /
• pp.1536-1545
• /
• 2008

In this paper, we research a new method for efficiency improvement of a single-phase Induction motor by minimization of the stator loss. To make this, we perform winding design which is based on balanced and quasi-balanced operation condition. It gives efficiency improvement greatly but poor starting torque simultaneously. To obtain the best efficiency improvement maintaining the maximum and starting torque, the optimal winding specification and rotor dimension is determined with variation of secondary resistance, running capacitor and turn ratio. Finally, this paper gives the comparison between the simulation results and experimental results.

• 조명전기설비학회논문지
• /
• 제16권4호
• /
• pp.64-72
• /
• 2002

산업의 발달에 따라 선형 직류 모터의 용용이 확대되고 있다. 본 연구에서는 가동차석형 양측식 다분할 여자 LDM의 해석을 연구대상으로 하였다. 본 LDM의 구조에서 가동자는 큰 추력을 얻도록 영구지석 6개를 사용하였으며, 고정자는 철심의 포화를 억제 하도록 다 분할형 권선을 성층하였다. 또한 양측 여자 권선은 지그재그형으로 성 층하여 추력의 리플을 억제하고, 정추력을 발생할 수 있도록 설계하였다. 여기에 다 분할시 영구자석대 권선 폭의 비가 중요하므로 본 연구에서는 똑비를 1 : 1, 1 : 0.84 및 1 : 0.5의 3개 부분으로 나누어 해석하였다. 해석 방법은 복잡한 수치해석의 유한요소법 보다는 퍼미언스 및 자기저항 법을 이용하여 파라며터를 계산하였다. 제작된 실험장 치를 통하여 추력을 측정한 결과는 전 변위에 대해서 정추력이 발생함을 알 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.62-64
• /
• 2007

This paper deals with design of high speed linear switched reluctance motor(LSRM). First, we derived design factor from pole arc ratio of stator and mover, and calculated time constant using inductance and resistance. Second, we decided design parameter from design factor using time constant. Finally, analyze characteristics for LSRM using finite element analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.59-61
• /
• 2008

This paper deals with design of Linear Switched Reluctance Motor (LSRM) considering to normal force. First, we derived design factor from pole arc ratio of stator and mover, and calculated time constant using inductance and resistance. Second, we decided design parameter from design factor using time constant, and analyze characteristics for LSRM using finite element analysis. Finally, we analyzed force characteristic according to design factor.