• 한국산학기술학회논문지
• /
• 제21권11호
• /
• pp.861-869
• /
• 2020

대용량 유도전동기용 인버터 개발을 위한 부하 장치는 고가의 제작 비용 및 제작에 많은 시간이 필요하므로 유도전동기 및 부하 장치를 대체할 수 있는 시뮬레이터 개발에 대한 필요가 증대되고 있다. 기존의 대용량 3상 유도전동기의 인버터용 부하 시뮬레이터는 리액터와 3상 PWM 정류기를 사용하여 시험용 인버터의 전류를 제어함으로써 단지 인버터의 부하로만 작용할 뿐 유도전동기의 특성을 모사하기 어렵다. 본 논문에서는 LCL 필터와 3상 PWM 정류기를 이용하여 3상 유도전동기의 모델과 부하 특성을 모사할 수 있는 실시간 시뮬레이터를 제안한다. PWM 인버터에 흐르는 전류는 3상 유도전동기의 고정자 전류를 모사하며 LCL 필터의 인덕터에 흐르는 전류와 커패시터 전압에 의해 제어된다. LCL 필터의 커패시터 전압은 3상 유도전동기의 회전자 자속에 의해 고정자 권선에 유기되는 유도기전력을 모사하며 인덕터 전류와 PWM 정류기에 의해 제어된다. 3상 유도전동기의 회전자 전류, 고정자 및 회전자 자속, 전동기 토크, 슬립 주파수 및 회전자 속도는 인버터에 흐르는 전류와 유도전동기의 상수로부터 유도된다. MATLAB/Simulink 시뮬레이션을 통하여 제안된 3상 유도전동기용 실시간 시뮬레이터의 전기적, 기계적 모델 특성 및 벡터제어 동작을 검증하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권5호
• /
• pp.241-248
• /
• 1999

Recently, many linear motion generators and motors are rapidly finding applications that ranges from short stroke linear motion vibrators, such as dynamic cone type loudspeakers to stirling engine driven linear reciprocating alternators, compressors, textile machines etc. The stroke-length may go up to 2m, and the maximum speed is in the range of 5 to 10m/s with oscillating frequency as high as 15 kHz. Therefore, the linear oscillating actuators(LOAs) may be considered as variable speed drivers of precise controller with stoke-length and reversal periods during the reciprocating motion. In this paper, the design, fabrication, experiments, and extraction of control parameters of a moving coil type LOA for driving of linear reciprocating motion control systems, are treated. The actuator consists of the NdFeB permanent magnets with high specific energy as the stator produced magnetic field, a coil-wrapped nonmagnetic hollow rectangular bobbin structure, and an iron core as a pathway for magnetic flux. Actually, the design is accomplished by using FEM analysis for the basic configuration of a magnetic circuit, and characteristic equations for coil design. In order to apply as the drivers of a linear motion reciprocating control system, the control parameters and circuit parameters, such as input voltage-stoke, exciting frequency-stoke, coil inductance and so on, are extracted from the analysis and experiments on concerning a fabricating LOA.

• 전기학회논문지P
• /
• 제66권2호
• /
• pp.69-75
• /
• 2017

The gas turbine static starter rotates the stationary synchronous machine by the interaction of the rotor and the stator. The detection from the initial position of the rotor has been an important issue to drive with optimum torque. Previously, the gas turbine starter was used by attaching the encoder to the synchronous machine, but the position and velocity of the rotor have been estimated by sensor-less method until recently due to the difficulty in attaching and detaching and damage caused by the shaft voltage noise. In this paper, Rotor initial(stationary state) position estimation, forced commutation control(speed less than 10%), and natural commutation control(speed more than 10%) method using magnetic flux with integrated terminal voltage were presented and the sensor-less speed control performance was verified. As a result of making and evaluating the 29 kVA synchronous machine and the starting device, the performance of each control mode was satisfactory. Furthermore, the applied technology is expected to be used for the development of the gas turbine starter of tens of MW class and the field application.

• Journal of Power Electronics
• /
• 제6권1호
• /
• pp.52-66
• /
• 2006

This paper proposes a wind energy conversion system connected to a grid using a self-excited induction generator (SEIG) based on the maximum power point tracking (MPPT) control scheme. The induction generator (IG) is controlled by the MPPT below the base speed and the maximum energy can be captured from the wind turbine. Therefore, the stator currents of the IG are optimally controlled using the indirect field orientation control (IFOC) according to the generator speed in order to maximize the generated power from the wind turbine. The SEIG feeds a (CRPWM) converter which regulates the DC-link voltage at a constant value where the speed of the IG is varied. Based on the IG d-q axes dynamic model in the synchronous reference frame at field orientation, high-performance synchronous current controllers with satisfactory performance are designed and analyzed. Utilizing these current controllers and IFOC, a fast dynamic response and low current harmonic distortion are attained. The regulated DC-link voltage feeds a grid connected CRPWM inverter. By using the virtual flux orientation control and the synchronous frame current regulators for the grid connected CRPWM inverter, a fast current response, low harmonic distortion and unity power factor are achieved. The complete system has been simulated with different wind velocities. The simulation results are presented to illustrate the effectiveness of the proposed MPPT control scheme for a wind energy system. In the simulation results, the d-q axes current controllers and DC-link voltage controller give prominent dynamic response in command tracking and load regulation characteristics.

• 수산해양기술연구
• /
• 제60권1호
• /
• pp.71-79
• /
• 2024

In compliance with environmental regulations at sea and the introduction of unmanned autonomous ships, electric propulsion ships are garnering significant attention. Induction machines used as propulsion electric motor (PEM) have maintenance advantages, but speed control is very complicated and difficult. One of the most commonly used techniques for speed control is DTC (direct torque control). DTC is simple in the reference frame transformation and the stator flux calculation. Meanwhile, two-level and three-level voltage source inverters (VSI) are predominantly used. The three-level VSI has more flexibility in voltage space vector selection compared to the two-level VSI. In this paper, speed is controlled using the DTC method based on the specifications of the PEM. The speed controller employs a PI controller with anti-windup functionality. In addition, the characteristics of the two-level VSI and three-level VSI are compared under identical conditions. It was confirmed through simulation that proper control of speed and torque has been achieved. In particular, the torque ripple was small and control was possible with a low DC voltage at low speed in the three-level VSI. The study confirmed that the application of DTC, using a three-level VSI, contributes to enhancing the system's response performance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 추계학술대회 논문집 학회본부
• /
• pp.20-24
• /
• 1989

The time optimal position control scheme can be repeatedly taken from the initial state of a dynamic system to a desired one as fast as possible at the industrial drives. In this case, the machine parameters will vary due to temperature, frequency, and saturation effects. In particular, the rotor resistance value changes dramatically with temperature and frequency. These changes affect the command values of the stator current components and slip speed. There is a mismatch between the commanded variables and actual variables of the induction motor drive, and this situation leads to decoupling of the vector controller from the plant, i.e the induction motor. Consequences of such decoupling include the initiation of oscillations of the rotor flux and unsuitable switching of electromagnetic torque of the induction motor servo drive. Therefore, a rotor resistance parameter compensating method for the induction motor is described.

• Journal of Electrical Engineering and Technology
• /
• 제7권6호
• /
• pp.926-931
• /
• 2012

Since robot industry growing, the machine that could move with multi-DOF has been studied in many industrial fields. Spherical motor is one of the multi-DOF machine that doesn't need gear for multi-DOF motion. Unlike conventional motor, spherical motor can not only rotate on the shaft axis (rotating motion), but tilt the shaft with 2-DOF motion (positioning motion). In the typical type of spherical motor, one coil took part in positioning motion and rotating motion at the same time. As the result, the control algorithm was complex. To solve this problem, this study proposed a novel type of coil on the stator. The coils were separated for positioning motion and rotating motion. Thus the linkage flux of rotating coil didn't be affected the positioning angle. In this paper, comparing the back-EMF of typical and novel type was conducted and the driving experiment was carried out as the positioning angle. From the experiment result, the performance of proposed spherical motor could be verified.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.59-61
• /
• 1995

This paper presents the cogging torque analysis of the permanent magnet type AC servo motor which have the closed slot structure. Generally, existence of the slot opening causes the cogging torque. But the cogging torque exists in this type motor(having closed slot structure) because the bridge part is saturated by the rotor flux. In this paper, the finite element analysis is used to calculate the cogging torque and the rated torque. As the size of the bridge part-the thickness and the width-changes, the cogging torque and the rated torque are obtained repeatedly like as upper procedures. Finally, the trends of the cogging torque and the rated torque versus the size of the bridge part are obtained from this analysis procedures. By this approach, the optimal geometry of the bridge part can be found which minimize the cogging torque satisfying the required value of the rated torque.

• Journal of Magnetics
• /
• 제20권1호
• /
• pp.79-85
• /
• 2015

This paper presents a comparative study of a Tubular Linear Machine (TLM) with an Axially Magnetized Single-sided Permanent Magnet (AMSPM) and an Axially Magnetized Double-sided Permanent Magnet (AMDPM) based on analytical field calculations. Using a two-dimensional (2-D) polar coordinate system and a magnetic vector potential, analytical solutions for the flux density produced by the stator windings are derived. This technique is significant for the design and control implementation of electromagnetic machines. The field solution is obtained by solving Maxwell's equations in the simplified boundary value problem consisting of the air gap and coil. These analytical solutions are then used to estimate the self and mutual inductances. Two different types of machine are used to verify the validity of these model simplifications, and the analytical results are compared to results obtained using the finite element method (FEM) and experimental measurement.

• 조명전기설비학회논문지
• /
• 제20권1호
• /
• pp.48-56
• /
• 2006

본 논문에서는 고정자의 3고조파 전압 성분을 이용하여 브러시리스 직류 전동기의 회전자 위치를 간접 검출하는 방법을 제안하였다. 3고조파 전압 성분은 회전자의 위치 정보를 가지고 있고 이 전압을 이용하여 정류 신호를 만들어 낼 수 있다. 따라서 정류 신호를 이용한 브러시리스 직류 전동기를 센서리스로 운전하는 방식은 역기전력 파형과 상전류가 비교적 정확한 동기를 유지할 수 있으므로 넓은 속도 범위에서 안정적인 센서리스 운전이 가능하다. 또한 정밀 속도 제어를 위해 PLL 회로를 적용함으로써 저속도에서도 높은 분해능을 얻을 수 있다. 따라서 기존에 속도 제어를 위해 필요했던 고가의 속도 센서인 레졸버와 엔코더 역할을 대체하여 전체적인 구동 회로의 가격을 낮출 수 있다.