• 전기학회논문지
• /
• 제56권3호
• /
• pp.547-555
• /
• 2007

In order to transmit energy generated through the stator winding of a doubly-fed induction generator (DFIG), we need to synchronize the generated voltage vector with the grid voltage vector. However, the existing synchronization methods work only when the encoder is installed at a specific position and equivalent constant is precise. In order to solve this problem, a new synchronization method has been proposed and a way of applying the method to existing doubly-fed induction generator control algorithm has been also proposed. The validities of the methods proposed were verified by using a prototype converter for a 1.5MW-class doubly-fed induction generator and experimental results showed the validity of that against variation of an encoder positions, generator parameters, and grid voltages.

• Journal of Electrical Engineering and Technology
• /
• 제6권2호
• /
• pp.226-232
• /
• 2011

The $H_{\infty}$ approach, adopted in this paper, is based on loop shaping using a normalized coprime factor combined with a field-oriented control to control induction motor. We develop two loops. The first one, the inner loop, controls the stator current by $H{\infty}$ controller in order to obtain good performance. The second loop, the outer one, guarantees stability and tracking performance of speed and rotor flux using a proportional integral controller. When the rotor flux cannot be measured, we introduce a flux observer to estimate the rotor flux. Simulation and experimental results are presented to validate the effectiveness and the good performance of this control technique.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.705-708
• /
• 2000

Switched Reluctance motors(SRM) attract much attention in motor because they are reliable and inexpensive. With advance in power electronics and high-speed processors the performance of SRM has been enhanced greatly. But they require rotor position information to operate, In many systems rotor position sensors are undesirable and have disadvantages. To overcome the disadvantages include by position sensors a number of sensorless methods for SRM's have been proposed by researchers. This paper describes a method for indirect sensing of rotor position in SRM's pulsewidth modulation voltage control. The method required no priori knowledge of motor parameters excepts for the number of stator and rotor poles. The detection method uses the change of the derivative of the phase current to detect the position.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.311-318
• /
• 2005

이 논문은 다른 종류의 유도전동기 구름베어링 손상을 유도전동기 고정자 전류신호해석을 통하여 검출하고 실시간으로 손상을 진단하는 알고리즘을 개발하였다. 유도전동기 구름베어링의 손상을 검출하기 위하여 정상적인 베어링을 갖는 유도전동기, 축정열에 불량을 가지고 있는 전동기와 베어링 외륜에 구멍을 가지고 있는 2가지 종류의 비정상 베어링을 갖는 유도전동기 3set를 실험시스템을 구축하였다. 또한 유도전동기의 구름베어링시스템의 비정상적인 상태에서 고정자전류을 검출하기 위하여 TMS320F2407 DSP 칩을 이용하여 데이터 획득보드를 개발하였다. 이 고정자전류신호를 해석을 통하여 베어링 손상을 검출하기 위한 방법으로 FPT, 웨이브렛 분석 및 내적에 의한 평균신호패던에 의한 분석결과를 제시하였다. 특히 내적에 의한 신호분석을 통하여 베어링 손상 여부를 실시간으로 진단할 수 있는 새로운 알고리즘과 분석방법을 제시하였다.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.23-34
• /
• 2008

This paper deals with a Direct Torque Control (DTC) of an Interior Permanent Magnet Synchronous Motor (IPMSM) for the Electric Vehicle (EV) propulsion system using a Neural Network (NN). The Conventional DTC with optimized switching lookup table and three level torque controller generates relatively large torque ripples in an electric vehicle motor drive. For reducing the torque ripples, a three level torque controller is hereby replaced by the five level torque controller. Furthermore, the switching lookup table of the five level torque controller based DTC is replaced with a Neural Network. These DTC schemes of an IPMSM drive are simulated using MATLAB/SIMULINK. The simulated results are compared with the conventional DTC and it is found that the ripples in the torque, as well as in the stator current, are reduced drastically.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2009년도 정기총회 및 추계학술대회 논문집
• /
• pp.96-98
• /
• 2009

This paper propose a method to detect the rotor position of IPMSM(Interior permanent magnet synchronous motor) at standstill without a position sensor. The proposed method is based on current variation caused by the magnetic saturation of stator core as rotor position. By choosing an appropriate voltage vector and applying it to phase winding, it enables the algorithm to discern between a north pole and south pole, and subsequently estimates an absolute position. This method dose not depend on the model of the motor and the motor parameter.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2009년도 정기총회 및 추계학술대회 논문집
• /
• pp.268-270
• /
• 2009

This paper proposes a simple starting method to arrange the rotor position of the blushless DC motor (BLDC) without additional sensors and any information of motor parameters. Both the stator current and time period for arranging the rotor position can be easily adjusted by modulating a pulse width of switching devices. Using the proposed method, it is demonstrated experimentally that the BLDC starts up very smoothly.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.957_958
• /
• 2009

2DOF is applied to induction moor in order to supply these weak points of PI speed control method in this paper. and proposed method utilize the combination of the voltage model based on stator equivalent model and the current model based on rotor equivalent model, which enables stable estimation of rotor flux. And it also emphasizes the improvement of the control characteristics in low speed region where established schemes have many problems. To prove the propriety of this paper, the various simulations carried out adequacy and stability using Matlab, and at the same time real system is made, so it is proved. As the results of embodying the system, the robust system is realized.

• 전기학회논문지
• /
• 제60권10호
• /
• pp.1858-1864
• /
• 2011

This paper suggests a control technique of the sensorless brushless DC (BLDC) motor drive for a vehicle fuel pump application. The sensorless technique based on a comparator and a potential start-up method with high starting torque are proposed. The comparator is used to generate the commutation signals in phase with the three-phase back-EMFs. The rotor position is aligned at standstill for maximum starting torque without an additional sensor and any information of motor parameters. Also, the stator current can be easily adjusted by modulating the pulse width of the switching devices during alignment. Some experiments are implemented on a single chip 16-bit DSP controller to demonstrate the feasibility of the sensorless techniques.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.125-129
• /
• 2006

In order to transmit energy generated through the stator winding of a doubly-fed Induct ion generator (DFIG), we need to synchronize the generated voltage vector with the grid voltage vector. However, the existing synchronization method works only when the encoder is installed at a specific Position and equivalent constant is precise. In order to solve this Problem, a new synchronization method has been proposed and a way of applying the method to existing doubly-fed induction generator control algorithm has been also proposed. The validity of the proposed methods have been verified using a prototype converter for the control of a 1.5MW-class doubly-fed induction generator