• Computers and Concrete
• /
• 제26권6호
• /
• pp.547-563
• /
• 2020

In this paper, the influence of axial compression ratio on the mechanical properties of new type joints of side span of rectangular concrete-filled steel tubular column-H-type steel beam is studied. Two new types of side-span joints of rectangular concrete-filled steel tubular column-H-type steel beam are designed and quasi-static tests of five new type joints with 1:2 scale reduction ratios are performed. The axial compression ratio of joint JD1 is 0.3, 0.4 and 0.5, and the axial compression ratio of joint JD2 is 0.3 and 0.5. In the joint test, different axial forces were applied to the top of the column according to different axial compression ratios, and low-cyclic reciprocating load was applied on the beam. The stress and strain distribution, beam and column deformation, limit state, failure process, failure mechanism, stiffness degradation, ductile deformation and energy dissipation capacity of the joint were measured and analyzed. The results show that: with the increase of axial compression ratio, the ultimate bearing capacity of the joint decreases slightly, the plastic deformation decreases, and the stiffness and ductility decrease. According to the energy dissipation curve of the specimen, the equivalent damping coefficient also increases with the increase of axial compression ratio in a certain range, indicating that the increase of axial compression ratio can improve the seismic performance of the joint to a certain extent. The finite element method is used to simulate the joint test, and the test results are in good agreement with the simulation results.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권2호
• /
• pp.35-42
• /
• 2021

본 연구에서는 NFPA 13을 참조하여 구조물 2층을 구현한 강재지그를 제작하였으며, 그루브 조인트의 배관연결재가 적용된 배관계통을 구성하고 정적 반복가력에 의한 지진모사실험을 수행하였다. 지진모사실험은 엑츄에이터로 건축물 내진설계기준의 최대허용 층간변위에 대한 반복가력실험을 수행하였다. 지진하중 발생 시 입상배관의 구조물에 대한 변형 또는 구조부재간의 상대변위에 의한 변위지배적인 거동에 따른 배관계통과 주요 배관요소의 지진거동을 분석하였다. 배관계통의 변형각은 기존의 센서를 이용하여 측정하기가 어려우므로 이미지측정시스템을 적용하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권4호
• /
• pp.11-22
• /
• 2023

본 연구에서는 원심성형 기법을 이용하여 구조용 콘크리트 각형보를 개발하였으며, 단면의 휨 강성을 확보하기 위하여 단면의 중 공률은 10 % 이하로 하며 이를 위하여 기존의 빈배합상태의 콘크리트가 아닌 고슬럼프(150~200 mm)의 물성을 가지며 설계강도가 100 MPa 이상인 콘크리트 배합비를 개발하여 적용하고, 원심성형 각형보를 제작하기 위한 특수거푸집을 제작하여 원심성형 각형보를 생산하였다. 생산된 원심성형 각형보는 원심성형 부재의 표준 휨 및 전단 시험기준에 따라 성능시험을 수행하였다. 4개의 시험체에 대한 정적재하시험 결과는 설계기준에서 제시하고 있는 단면의 공칭휨강도, 공칭전단강도 이상으로 나타나 초고강도 원심성형 각형보의 구조적인 신뢰성이 입증되었다.

• 한국운동역학회지
• /
• 제26권2호
• /
• pp.229-236
• /
• 2016

Objective: This study aimed, first, to develop core strength training equipment with elderly-friendly, easy-to-use features and, second, to investigate the effect of core strength training using the equipment on the performance and stability of the elderly in activities of daily living. Method: In this study, we developed training equipment with a stability ball that can be used for performing core strength exercises in the elderly. Twenty-three elderly subjects (age: $77.87{\pm}6.95years$, height: $149.78{\pm}6.95cm$, and weight: $60.57{\pm}7.21kg$) participated in this study. The subjects performed the core strength training exercise with 16 repetitions for 8 weeks (2 repetitions per week). Performance in activities of daily living was assessed by using the Short Physical Performance Battery (SPPB), a test of going up and down 4 stairs, and one-leg static balance test. Stability was quantified as changes in the center of pressure (COP) and C90 area. Results: With the core strength equipment, trunk core strength exercise could be performed by pulling or pushing a rope with 2 hands on the stability ball. During the task, the tension in the rope was manipulated by a motor connected to the rope and the COP of the subject was measured by 4 load cells mounted in the equipment. Our results showed that the SPPB score was significantly higher (p < .05), the time to complete the "going up and down 4 stairs" test was significantly shorter (p < .05), and one-leg static balance statistically improved under an eyes-open condition (p < .05) after as compared with before the core strength training. The changes in the COP in the anteroposterior and mediolateral directions, and C90 area were significantly lower in the posttest (p <. 05) than in the pretest. Conclusion: The core strength training exercise using the equipment developed in the present study improved the performance and stability of the elderly in activities of daily living.

• 한국건설순환자원학회논문집
• /
• 제11권4호
• /
• pp.355-363
• /
• 2023

노후 교량의 안전성을 평가하는 방법에 있어서 동특성과 처짐은 구조계의 강성과 직접 연관이 있으며, 처짐의 경우에는 교량 사용자가 직접 감지할 수 있는 물리량으로 가장 중요한 인자이다. 하지만 교량의 처짐을 측정하기 위해서는 교량의 하부에 처짐계를 설치하고 교통 차단 및 재하시험을 실시해야 하는 번거로움이 있어 교량의 환경에 따라서 비용이 증가하거나 측정이 불가능한 문제들이 발생하고 있다. 본 연구에서는 처짐계의 설치 없이 가속도계만을 이용하고 재하시험 없이 상시 진동을 이용하여 교량의 처짐을 측정하는 방법을 제안하였다. 상시 진동을 이용한 교량 동특성 및 처짐 분석을 위해 단순한 연산으로 빠른 분석이 가능하다고 알려진 TDD 기법을 이용하여 교량의 모드형상과 고유진동수를 추출하였으며, 유연도 분석을 통하여 교량의 단위하중 처짐을 분석하여 정적 처짐까지 산정하였다. 본 제안 기술의 검증을 위해 공용중 교량인 C대교(사장교)에 적용하여 모드형상, 고유진동수, 정적 처짐 분석을 수행하였으며 재하시험 실측값과 구조해석 자료와 비교하였다. 그 결과 모드형상 및 고유진동수는 0.42~1.13 %, 중앙경간에서의 최대 처짐은 3.58 %의 오차율을 확인하였다. 따라서 제안기술은 처짐계의 설치가 어려워 실측이 불가능한 교량의 처짐을 추정하여 설계값 및 해석값 대비 처짐 발생량 비교로 교량의 안전성을 간접적으로 파악할 수 있는 근거 자료로 활용 가능할 것으로 사료된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.389-392
• /
• 1999

Fatigue is a process of progressive permanent internal structural change in a material subjected to repeitive stresses. These change may be damaging and result in progressive growth of cracks and complete fracture if the stress repetitins are sufficiently large. For structural members subjected to cyclic loads, the continuous and irrecoverable damage processes are taking place. These processes are referred as the cumulative damage processes due to fatigue loading. Moreover, increased use of high strength concrete makes the fatigue problem more important because the cross-section and dead weight are reduced by using high strength concrete. The purpose of this study is to investigate the shear fatigue behavior of reinforced concrete beams according to shear reinforcement ratio and concrete compressive strength under repeated loadings. For this purpose, comprehensive static and fatigue tests of reinforced concrete beams were conducted. The major test variables for the fatigue teats are the concrete strength and the amount of shear reinforcements. The increase of deflections and steel strains according to load repetition has been plotted and analyzed to explore the damage accumulation phenomena of reinforced concrete beams. An analytical model for shear fatigue behavior has been introduced to analyze the damage accumulation under fatigue loads. The failure mode and fatigue lives have been also studied in the present study. The comparisons between analytical results and experimental data show good correlation.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.203-212
• /
• 2002

Active magnetic hearings allow much high surface speed than conventional ball bearings and therefore greatly suitable for high speed cutting. This paper describes a design and test of an active magnetic bearing system with 16-pole radial magnets. The spindle is originally designed for a CNC lathe and driven by outer motor with 5.5 kW power and maximum speed 10,000 rpm. Considering static load condition and geometric restrictions, radial magnet is designed 16-pole type for smaller outer diameter of the spindle system. Dynamic system characteristics such as natural frequency, critical speed, stiffness, damping and system stabilities are simulated with a rigid rotor model including direct feedback controller. The designed spindle system is realized with digital PIDD controller to compensate phase lag of PWM amplifier and magnet coils. With levitation and step response experiment the control system characteristics are tested, and the spindle is rotated up to 10,000 rpm stab1y.

• 한국강구조학회 논문집
• /
• 제24권4호
• /
• pp.371-382
• /
• 2012

기존의 전단벽 시스템은 커플링보를 강하게 설계하는 경우가 많아 상대적으로 내력 및 강성이 낮은 콘크리트 코어와 특정층에 손상이 발생되기 쉬워 건물의 연성이 저하된다. 전단벽 시스템의 연성능력 및 내진성능을 향상시키기 위해 본 연구에서 강성은 기존의 커플링보 이상으로 발휘되면서 설계하중에 따라 내력을 용이하게 변화시킬 수 있는 강재이력댐퍼를 커플링보에 적용하였다. 강재이력댐퍼는 2단으로 직렬 연결된 형상으로 제안하였고, 제안된 강재이력댐퍼의 구조성능을 검증하기 위하여 정적실험을 수행하였다. 또한 FEM 해석결과를 실험결과와 비교 검증하고 강재이력댐퍼의 초기강성, 에너지 흡수능력, 변형능력 등을 분석하여 설계 근사식을 제안하였다.

• 한국기계가공학회지
• /
• 제9권2호
• /
• pp.47-52
• /
• 2010

Miniaturization and lightweight are increasingly the recent trend in the manufacture of electric appliances and machine parts. So technology of micro joining for joining materials is indispensable. This paper gives a description of an experimental study of the ultrasonic welding of metals. In ultrasonic metal welding, high frequency vibrations are combined with pressure to join two materials together quickly and securely, without producing significant amount of heat. Ultrasonic metal welder consists of Transducer, Booster, and Horn that are designed very accurately to get the natural frequencies and vibration mode. In this study, The horn was designed and analyzed the natural frequency by the modal analysis and harmonic analysis. And using a fiber optic sensor, we measured the amplitude and analyzed the Fast Fourier Transformed result. Using the horn, Ultrasonic metal welding between Ni sheet and Ni sheet of 0.1mm thickness was accomplished under the optimal conditions of static pressure 0.15MPa, vibration amplitude 45% and welding time of 0.28s. This result can be used for ultrasonic metal welding in manufacturing industry.

• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1864-1871
• /
• 2017

This paper presents a design of a 2-phase segmental stator type 4/3 switched reluctance motor (SRM) for air-blower application. The air-blower requires only one direction rotation, high rotor speed without torque dead-zone. In order to satisfy the requirements of the load, the rotor of the 4/3 proposed SRM is designed with wider rotor pole arc and non-uniform air-gap is applied on the rotor shape. With a special rotor structure, the motor generates a wider positive torque region and has no torque dead-zone. The stator of the proposed SRM is constructed with two segmental C-cores, and there are no magnetic connections between 2 C-cores. The flux follows in a short closed loop in each C-core and has no reversal flux in the stator. The static and dynamic characteristics of the proposed motor are analyzed by the finite element method (FEA) and Matlab-Simulink, respectively. In order to verify the design, a prototype of the proposed motor has manufactured for laboratory test. The performance of the proposed motor is verified by the simulation and experimental results.