• Korean Journal of Environmental Agriculture
• /
• v.27 no.2
• /
• pp.145-149
• /
• 2008

Anaerobic co-digestion of swine manure and food waste for biogas production was performed in serum bottles at various volatile solids(VS) contents and mixing ratios of two substrates(swine manure:food waste=$100:0{\sim}0:100$). Through kinetic mode of surface methodology, the methane production was fitted to a Gompertz equation. The ultimate methane production potential of swine manure alone was lower than that of food waste regardless of VS contents. However, it was appeared that maximum methane production potentials in 80 : 20 of the mixing rate at VS 3% was enhanced at 144.7%, compared to its only swine manure. The potential increased up to 815.71 ml/g VS fed as VS concentration and food composition increased up to 3.0% and 20%, respectively. The ultimate amount of methane produced had significantly a positive relationship with that of methane yield rate. Overall, it would be strongly recommended that feeding stocks use 20% of mixing ratio of food waste based on VS 3% contents when operating the anaerobic reactor on site at $35^{\circ}C$ if not have treatment of its anaerobic waste water.

• Nuclear Engineering and Technology
• /
• v.54 no.5
• /
• pp.1914-1928
• /
• 2022

To improve the heat transfer efficiency of the reactor fuel assembly, it is necessary to accurately calculate the two-phase flow boiling characteristics and the critical heat flux (CHF) in the fuel assembly. In this paper, a Eulerian two-fluid model combined with the extended wall boiling model was used to numerically simulate the 5 × 5 fuel rod bundle with spacer grids (four sets of mixing vane grids and four sets of simple support grids without mixing vanes). We calculated and analyzed 11 experimental conditions under different pressure, inlet temperature, and mass flux. After comparing the CHF and the location of departure from the nucleate boiling obtained by the numerical simulation with the experimental results, we confirmed the reliability of computational fluid dynamic analysis for the prediction of the CHF of the rod bundle and the boiling characteristics of the two-phase flow. Subsequently, we analyzed the influence of the spacer grid and mixing vanes on the void fraction, liquid temperature, and secondary flow distribution. The research in this article provides theoretical support for the design of fuel assemblies.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.9
• /
• pp.623-629
• /
• 2017

Flow structure and mixing characteristics in a micro combustor with a multi-hole baffle were numerically studied using the Reynolds stress model. The multi-hole baffle has geometrical features to produce multiple three-dimensional vortices inside combustion chamber. When the thickness of the baffle's geometrical factors changes, variations of vortical structures occur variously. Among these vortices, the vortex generated from the fuel stream exerts a critical influence on the mixing enhancement. The three-dimensional vortical structure, in its development state, was strongly dependent on the baffle thickness. In particular, as the baffle thickness decreases to values less than the diameter of the fuel hole, the jet stream in baffle holes changes from the parabolic to saddleback profile type. The sizes of recirculation zones inside combustion chamber and the mixing state were closely affected by the structure of the jet streams.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.5
• /
• pp.63-68
• /
• 2009

This study describes to analyze foam mixing characteristics in steady state to enhance the performance of proportioner for foam system designed to accurately proportion a foam liquid concentrate into a water stream up to constant concentration. The proportioner developed is experimentally evaluated in performance evaluation system consisted of a pump, tanks, pressure gauges, flow meters, a nozzle. As a result, the foam mixing performance of the line proportioner is found to increase with increased the water flow rate due to the venturi effect and with increased the cross-sectional area of the orifice and is analysed with 3 % in the error rate of $\pm4%$. For the pressure proportioner, the foam mixing performance is analyzed to increase with increased the water flow rate and with increased the inlet pressure and is analysed with 3% in the error rate of $\pm2%$.

• Nuclear Engineering and Technology
• /
• v.51 no.5
• /
• pp.1218-1230
• /
• 2019

A sub-channel solver, named ${\underline{S}}teady$ and ${\underline{T}}ransient$ ${\underline{A}}nalyzer$ for ${\underline{R}}eactor$ ${\underline{T}}hermal$ hydraulics (START), has been developed using the homogenous model for two-phase conditions of light water reactors. The code is developed as a fast and accurate TH-solver for coupled and multi-physics calculations. START has been validated against the NUPEC PWR Sub-channel and Bundle Test (PSBT) database. Tests like single-channel quality and void-fraction for steady state, outlet fluid temperature for steady state, rod-bundle quality and void-fraction for both steady state and transient conditions have been analyzed and compared with experimental values. Results reveal a good accuracy of solution for both steady state and transient scenarios. Axially different values for turbulent mixing coefficient are used based on different grid-spacer types. This provides better results as compared to using a single value of turbulent mixing coefficient. Code-to-code evaluation of PSBT results by the START code compares well with other industrial codes. The START code has been parallelized with the OpenMP algorithm and its numerical performance is evaluated with a large whole PWR core. Scaling study of START shows a good parallel performance.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.121-125
• /
• 2003

Micromixer plays an important role in Bio-MEMS or ${\mu}-TAS$. Mixing is generally generated by turbulence and interdiffusion of two fluids. Because of low Reynolds number(Re << 2000) in ${\mu}-channel$, it is difficult to generate turbulence, so mixing mainly depends on interdiffusion. Thus long channel distance is required to mix two different fluids. To reduce the channel length required for mixing, we propose the a new active ${\mu}-mixer$ that two fluids are effectively mixed in ${\mu}-channel$ by the ultrasonic wave which is generated by PZT. The ultrasonic wave is radiated into a chamber in the cross-section directional direction to interface with the two fluids. The two fluids are positioned one on top of the other. Mixing state is measured by the changing of color due to the reaction of NaOH and phenolphtalein.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.7-9
• /
• 2003

Solid-state reactions in Ni/Si multilayered films (MLF) with an overall stoichiometry of $Ni_2Si$, NiSi and $NiSi_2$, induced by ion-beam mixing (IBM) and thermal annealing, were studied by using spectroscopic ellipsometry and magneto-optical spectroscopy as well as x-ray diffraction (XRD). The mixing was performed with Ar+ ions of an energy of 80 keV and a dose of $1.5 x\times10^{16}$ $Ar^+$/$\textrm{cm}^2$. It was shown that the IBM induces structural changes in the Ni/Si MLF, which cannot be detected by XRD but are confidently recognized by the optical method. A thermal annealing at 673 K of the Ni/Si MLF with an overall stoichiometry of NiSi and $NiSi_2$ causes formation of the first η -NiSi phase. The first trace for $NiSi_2$ phase on the background of NiSi one was detected by XRD after an annealing at 1073 K while, according to the optical results, $NiSi_2$ turns out be the dominant phase for the annealed Ni/Si MLF with an overall stoichiometry of $NiSi_2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.1
• /
• pp.585-592
• /
• 2014

Mixing effect on anaerobic digestion of livestock wastewater was different results depending on the researchers have been reported. The purpose of this study was to understand application of Korea livestock waste it was necessary to determine the effect of mixing. 4 anaerobic reactors were operated mesophilic and thermophilic temperature with continuous mixing or non mixing condition, respectively. Experimental result showed If temperature was same, TCOD removal efficiency of continuous mixing reactor was 0.11-0.58% higher than non mixing reactor. Different mesophilic and thermophilic temperature, there was no significant difference of TCOD removal efficiency. Continuously mixed digester gas production was 1.7-4.6% higher than non mixed digester. In addition, mesophilic digester gas production was 29.1-32.1% higher than the thermophilic digester. It was due to the thermophilic digester believe the inhibition of ammonia. This study suggest that the optimized operation condition of anaerobic digestion for livestock wastewater treatment was mesophilic continuous mixing state.

• Bulletin of the Korean Mathematical Society
• /
• v.41 no.1
• /
• pp.189-198
• /
• 2004

In this study we consider quantum dynamical semi-group with a normal faithful invariant state. A quantum dynamical semigroup $\alpha\;=\;\{{\alpha}_t\}_{t{\geq}0}$ is a class of linear normal identity-preserving mappings on a von Neumann algebra M with semigroup property and some positivity condition. We investigate the asymptotic behaviors of the semigroup such as ergodicity or mixing properties in terms of their eigenvalues under the assumption that the semigroup satisfies positivity. This extends the result of [13] which is obtained under the assumption that the semi group satisfy 2-positivity.

• International Journal of Concrete Structures and Materials
• /
• v.7 no.2
• /
• pp.165-174
• /
• 2013

Portland cement concrete exposed to high temperatures during mixing, transporting, casting, finishing, and curing can develop undesirable characteristics. Applicable requirements for such the hot weather concrete differ from country to country and government agencies. The current study is an attempt at evaluating the hardened properties of the concrete exposed to hot weather in fresh state. First of all, this study reviews the current state of understanding and practice for hot weather concrete placement in US and then roadway sites with suspected hot weather concrete problems were investigated. Core samples were obtained from the field locations and were analyzed by standard resonance frequency analysis and the boil test. Based on the results, there does not appear to be systematic evidence of frequent cracking problems related to high temperature placement. Thus, the suspicious deteriorations which are referable to hot weather concreting would be due to other factors.