The weight-to-power ratio of the standard truck for the climbing lane design is known to be 200lb/hp. The value was known to be assumed based on constant trucks' capability and regional distributions in stead of widely varied distributions region by region. Additionally, this value was assumed after investigating registered vehicles' statistics instead of investigating real portions of truck volumes. Therefore, it may be said that the value of the current standard truck does not reflect regional or industrial diversity and proportions of truck volumes. To resolve these issues, the present paper studies diversified standard trucks which consider regionally or industrially diversified and observed-volume based weigh-to-power ratios. For this purpose, individual trucks' weigh-to-power ratios obtained at toll-gates of national expressways were used. For regionally based study, the whole nation are divided into 8 regions, then each region is characterized by a unit of a weigh-to-power ratio. The applicability of each value is provided. Results show that the single value for the nationwide standard truck may be 208 lb/hp, 8 lb/hp higher than the current value of 200 lb/hp. Results also show that regional values ranged widely from 170 lb/hp to 230 lb, 30 lb/hp higher/lower than the current value. Conclusively, regional diversity of trucks' weigh-to-power ratios was identified then three types of standardized weigh-to-power ratios which may represent regional characteristics were suggested. As the diversified standard truck are applied to the design standard, two benefits are expected such as decrease of rear-end accident rates or decrease of climb lane construction costs.
PURPOSES : This study estimated an asphalt pavement internal behavior under uphill lanes considering reducing speed of heavy truck on uphill slope. METHODS : Truck performance curve which has been adapted to "Korea Highway Capacity Manual" was analyzed. And asphalt pavement internal behaviors were estimated with Multi-layered elastic analysis using KPRP(Korea Pavement Research Program) dynamic modulus prediction equations. RESULTS : As a result, it is shown that when the standard truck drives 2.0 km at a speed of 80 km/h in 8% climbing slope, it's speed reduced to 25.4 km/h, at same time frequency in asphalt layer decrease to 67.2% and it's dynamic modulus degrades to 30.9%. Based on these results, internal behavior as decreasing vehicle speed on uphill lanes were estimated. CONCLUSIONS : From the results of Multi-layered elastic analysis, internal behavior showed that when the standard truck drives 2.0 km at a speed of 80 km/h in 8% slope on uphill lanes, vertical strain was increased to 44.4% at the bottom of surface course, and lateral tensile strain was increased to 20.5% at the bottom of base course.
Rear collisions to expressway work trucks result many casualties these days. But, currently, no special measure are being taken except deploying sign trucks behind the working trucks. In the U.S and Europe, trucks with TMA(Truck Mounted Attenuator) are being deployed behind the working truck, which is regarded as the standard method for work area safety, thereby reducing the fatality rates and property damage tremendously. Also, standard for the performance of TMA are established and TMA can be used in the field only when it satisfies the standard. In Korea, neither the standard for nor any guide to the TMA exists. In the situation some manufacturer developed TMA without proper performance evaluation and marketed limited number of TMAs in the field. In the study, NCHRP350, which is the performance standard of expressway safety features of U.S. and materials related to the TMA standard in Europe have been reviewed to establish the Korean performance criteria. Based on the review, and incorporating existing Korean standard for crash cushions, domestic standard for TMA has been proposed and applied in developing Korean TMA and crash tested it to verify the performance. The original design developed was crash tested and modified. The newly proposed design was studied using impact simulation program several times. Modifications were made after each simulation and prototype was built and crash tested as per the newly established TMA performance criteria.
Proceedings of the Computational Structural Engineering Institute Conference
/
1992.04a
/
pp.126-133
/
1992
The structural soundness of bridges is mainly damaged by overloaded heavy vehicles. The increasing volumes of overloaded heavy vehicles has been indicated as serious state. As results several countries have revised their bridge load codes. However, because of variety of truck types and their weights it is difficult to develop rational standard truck loads. In addition the common practice that only one design configuration of standard truck is adopted to design variety of bridges causes further difficulties. The objective of the study is to investigate the statistical characteristics of vehicle loadings based on survey data col looted, in which some major factors, such as vehicle configurations, vehicle freights, traffic modes, etc. are incorporated.
Proceedings of the Computational Structural Engineering Institute Conference
/
2006.04a
/
pp.749-756
/
2006
Because of the orthotropic elastic properties and significant two-way bending action, orthotropic plate theory may be suitable for describing the behavior of concrete filled grid bridge decks. Current AASHTO LRFD Bridge Design Specification(2004) has live load moment equations considering flexural rigidity ratio between longitudinal and transverse direction, but the Korea highway bridge design specification(2005) doesn't. The Korea highway bridge standard specification LRFD(1996) considers an orthotropic plate model with a single load to estimate live load moments in concrete filled grid bridge decks, which may not be conservative. This paper presents live load moment equations for truck and passenger car, based on orthotropic plate theory. The equations of truck model use multiple presence factor, impact factor, design truck and design tandem of the Korea highway bridge standard specification LRFD(1996). The estimated moments are verified through finite-element analyses.
KSCE Journal of Civil and Environmental Engineering Research
/
v.12
no.4
/
pp.107-116
/
1992
The structural integrity of bridges is mainly damaged by overloaded heavy vehicles. The increasing volumes of overloaded heavy vehicles has been indicated as serious state. As results several countries have revised their bridge load codes. However, because of variety of truck types and their weights it is difficult to develop rational standard truck loads. In addition the common practice that only one design configuration of standard truck is adopted to design variety of bridges causes further difficulties. The objective of the study is to investigate the statistical characteristics of vehicle loadings based on survey data collected, in which some major factors, such as vehicle configurations, vehicle weights, traffic modes, etc., are incorporated. The vehicle load effects due to single presence of heavy truck are also tested with several short-span bridges and probabilistic characteristics of current design practices are evaluated.
PURPOSES : The purpose of this study is to revise the weight to power ratio of the representative truck in S. Korea. So far, S. Korea has been using the unit lb/hp, and the construction machines were not considered in the evaluation of the performance of trucks. METHODS : This study was performed to recommend the use of ISO system of units, and to analyze the weight to power ratios of the representative trucks in S. Korea, including the dump trucks, concrete mixer trucks, and asphalt and concrete diffusers. RESULTS: From this study, the 85 percentile value of the weight to power ratio of the trucks in S. Korea's was found to be 103.6 kg/kw. CONCLUSIONS : The performance standard for the representative truck has to be increased upward, considering the travel pattern of the dump trucks, concrete mixers, and asphalt and concrete diffuser trucks, travel distances, narrow area (work zone) of operation, and the saving in construction budget for climbing lane. Based on this study, the weight to power ratio of the representative truck in S. Korea could possibly be revised to 100~110 kg/kW.
Kim, Sang Gu;Kim, Young Chun;Sim, Dae Young;Lee, Yong Mun;Kim, Jong Won;Kim, Heung Rae
Journal of Korean Society of Transportation
/
v.32
no.5
/
pp.473-486
/
2014
This study aims to review whether climbing lane installment is needed by analyzing the impact that standard trucks have on traffic according to vertical alignment at SMART highway, and if climbing lanes are required to propose truck speed change curves based on slope length. We used VISSIM simulation model to obtain the speed change of the standard truck on uphill roads. The standard truck on climbing lanes was set for 100kg/kW (170lb/hp) with the entry speeds set and analyzed by 90, 100, and 110 km/h considering the future speed limit of trucks. The results of the research show that under SMART highway circumstance, the 1 and 2% vertical alignment is not needed at the climbing lane but 3% vertical alignment is necessary. In order to install the climbing lane at 3% vertical alignment, the speed change curve of truck depending on slope length of 90, 100, and 110km/h of entry speed is proposed.
A forklift truck, commonly used for transporting heavy materials in manufacturing industries, etc., is a useful machine. However accidents occur frequently during the operation of the machine. In order to prevent accidents it is necessary to examine the current safety regulations on a forklift truck. Because the regulations have not revised for a long time, they do not reflect the rapidly changing environment of industries. Proposed revision of standard on articles for forklift trucks was presented after analysing the causes of occurred injuries, comparing domestic standards with international standards and examining the survey results. We analyzed the safety regulation articles and the injuries according to the type of work conducted with forklift. The major differences in safety regulations between Korea and the major foreign countries were investigated. The opinions of field workers on the safety regulations were surveyed using e-mail or interview. As a result, it was found that preventing workers from contacting with the forklift is very important. To prevent accident due to movement of a stopped forklift, actions are necessary to prevent slip of a forklift. Also supervision is required to make workers fasten safety belt and to prohibit workers from using a forklift for undesignated purpose.
Park, Jongmin;Kim, Jongsoon;Kim, Dongkeon;Chang, Sewon;Kim, Ghiseok
KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
/
v.23
no.3
/
pp.183-190
/
2017
Carton clamp truck is widely perceived as the high-efficient handling equipment of factory premises and warehouse by its capability of palletless handling. Therefore, the significance of a lab-based handling simulation is becoming higher with the growth of clamp truck usage. In this study, preliminary FEA and design of handling test courses for the lab-based simulation of carton clamp truck handling were performed, and the PSD analyses were performed for the modified one for the test course proposed by Park et al. (2017) as well as ASTM D 6055 and ISTA 3B standards. For the vibration in all directions, the vibration energy intensity analyzed by ISTA 3B standard showed higher than that by the other two cases. A FEA was performed for the handling operation of the sudden stop of the clamps after lifting the target HCP (heavyweight refrigerator corrugated package, w=180 kgf) up to the specified height. The slip distance between the clamp arm and the target HCP was 0.85 mm. The simulation result of 0.85 mm was 3.7 times lower than the experimental result (3.2 mm) obtained by Park et al. (2017), and it was estimated that the deviation comes from both the experimental error by weight imbalance of target HCP, and excessive simplification during the FE modelling of target HCP.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.