• Journal of Environmental Health Sciences
• /
• v.20 no.1
• /
• pp.28-38
• /
• 1994

The objective of this study were to measure concentrations of indoor pollutants in public transportation systems to provide importance of indoor air quality in transportation systems to policy makers. Indoor air quality of the pollutants (CO, CO$_2$, PM-10) and environmental sources (temperature, humidity) were measured at subway, seat-type bus, and city-type bus in the Seoul area from April to September 1992. The same pollutants and environmental sources were also measured at selected bus stops and subway stations during October 1991-September 1992. The mean concentrations of indoor pollutants in the public transportation systems were showed 115.5 $\mu$g/m$^3$ in PM-10, 6.8 ppm in CO, and 2167.9 ppm in CO$_2$, respectively. The mean values of PM-10 and CO showed below the U.S. 24 hour standard value of PM-10 and the Korea ambient CO standard, while the mean concentrations of CO$_2$ exceeded the Korea CO$_2$ standard. The highest levels of indoor concentration at public transportation systems were PM-10 of 134.6 $\mu$g/m$^3$ in the subway, CO of 8.9 ppm in the city-type bus, CO$_2$ of 2,511.1ppm in seat-type bus, respectively. The results showed that indoor air quality in bus and subway seemed likely to be affected by number of passengers and outdoor air infiltrated from exhausted gases of automobiles.

• Journal of Korean Society of Transportation
• /
• v.20 no.5
• /
• pp.175-181
• /
• 2002

BIS(Bus arrival Information System) is a system that informs Passengers waiting at bus stops of the bus arrival time of next buses. However, when operating this system, it is not exactly known what type of bus arrival information should be provided. The purpose of this paper is to develop a model of the optimal bus arrival time to be informed for BIS. Analyzing Efficiency in the Seoul's Urban Bus Industry Using Data Envelopment Analysis. Two basic types of bus arrival information can be considered. One is Bus Locations : Where next buses are located and under what situation they are, such as the next bus departed from the previous stop, The other is Expected Arrival Time. Time to the arrivals of next buses. Characteristics of these two types of bus arrival time information provided for passengers waiting at bus stops for BIS are examined. The waiting time of passengers at bus stops is derived as a function of the bus arrival time to be informed. Some basic principles about the optimal bus arrival time to be informed are found. Finally, a case study assuming several simplifications is performed. One of the key findings is that there exists optimal arrival time to be informed other than the average arrival time. The optimal arrival time to be informed should be closer to the average arrival time for small and very large standard deviations and be earlier for certain amounts of standard deviations.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.1
• /
• pp.23-29
• /
• 2013

TCN(train communication network) standard was approved in 1999 by the IEC (IEC 61375-1) and IEEE (IEEE 1473-T) organizations to warrant a reliable train and equipment interoperability. TCN defines the set of communication vehicle buses and train buses. The MVB(multifunction vehicle bus) defines the data communication interface of equipment located in a vehicle and the WTB(wire train bus) defines the data communication interface between vehicles. The WTB and each MVB will be connected over a node acting as gateway. Also, to support applications demanding a high reliability, the standard defines a redundancy scheme in which the bus may be double-line and redundant-node implemented. In this paper we have presented protocol analysis platform for the WTB redundancy which is part of TCN system, to verify communication state of high-speed trains. As a confirmation of its validity, the technology described in this paper has been successfully applied to state monitoring and protocol verification of redundancy WTB based on TCN.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.148-154
• /
• 1997

The safety problems of buses have been arisen due to the increasing of road traffic. Occupant injuries are always possible in the rollover accident and the frontal impact. Thus the structure of bus should have sufficient strength to protect passengers under accidental loads. ECE(Economic Commission for Europe) regulation No.66 prescribes that the superstructure of the vehicle shall be sufficient strength for passengers' surviving and the residual space shall be preserved in the passenger compartment during and after the standard rollover accident situation. Rollover test and simulation on a large-sized bus was completed according to the regulation. The coordinates of the points on the bus were measured by photogrammetry system. The rollover situation was revived by structural crashes simulation software, PAM-CRASH, and it was checked that the structure still complied with the requirements of residual space during rollover situation. The residual space was preserved during rollover, so it was proved that the structure of the investigated bus had much probability of survival in rollover accidents.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.6
• /
• pp.1309-1320
• /
• 2015

This study made an attempt to analyse the relationship between operation environment and fleet size per route which represents the level of service for inner-city bus service. Regression analysis method has been adopted as main analysis tool and 98 routes of bus operation status in Ulsan city as of 2013 has also been selected for analysis target. Correlation analysis was performed to identify the relationship between dependent and independent variables. There are three types of model for whole sample, type operation, and bus route operation system. These are the results of the current study. 1. The model developed for whole sample of 98 routes is as follows. Y(Fleet Size)=$-4.532+0.00002877*X_1$(Revenue). This model shows that it is necessary to have more than 140 passengers per day to increase fleet size of each bus route in Ulsan. 2. Models developed by type of operation (which are standard, express, and middle sized) are shown below. Stand Bus : Y(Fleet Size)=$-10.954+0.00004283*X_1$(Revenue). It is identified that more than 153 passengers need to use standard bus to increase fleet size per each standard bus, Middle Sized Bus : Y(Fleet Size)=-0.859+0.00001438*X1(Revenue). For middle sized bus, at least 52 daily passengers are needed to increase number of bus in each route. 3. Models developed for each route operation systems are as belows. Joint Operation Group : Y(Fleet Size)=$-4.786+0.00003028*X_1$(Revenue). Individual Operation Group : Y(Fleet Size)=$-2.339+0.00002030*X_1$(Revenue). These model provide similar result which 140 people is the minimum number of passenger to raise the number of vehicles in each route. This result shows that the route operation systems does not affect the raise number of cars significantly.

• Journal of Biosystems Engineering
• /
• v.37 no.4
• /
• pp.225-232
• /
• 2012

Purpose: Accurate monitoring of information from various agricultural vehicles is one of the most important factors for appropriate management strategy of field operations. While there has been a number of study and design on applications of sensors and actuators for data acquisition and control system in tractor, incompatibility between various customized hardware and software has become a major obstacle to the universal deployment in real field operation. International standard for implementation of electronic control unit (ECU) in agricultural vehicles has becoming a mandatory requirement for inter-operation compatibility in the international trade of agricultural vehicle industries. The ISO 11783 standard is basically based upon well known communication technology designated using the controller area network (CAN) bus. While CAN bus could provide 1.0 Mbps of communication speed, the standard only recommended 250 kbps. Methods: This study presents the implementation and evaluation of ISO 11783 for tractor electronic control units (TECU)with a higher transmission rate from multiple ECU than 250 kbps. Throughput and loss rate of the developed prototype were calculated across manipulated bus load for laboratory experimental tests, and the maximum requirement of transmission rate by ISO 11873 was satisfied with lower than 60% of bus load. Results: Field tests with a TECU implemented to process messages from global positioning system (GPS) receiver resulted that the root mean square error of position information was lower than 4 m with 0.5 m/s as a travelling speed. Conclusions: Results of this study represent the utilization of the international standard ISO 11783 to providepractical developments in terms with the inter-operability of TECU.

• Journal of the Korea Society of Computer and Information
• /
• v.22 no.7
• /
• pp.9-16
• /
• 2017

In this paper, we propose a development method of portable Automatic Test Equipment based on PXIe platform. Legacy VME form factor structured test equipment has limited reuse and expansion of modules due to unapplied bus specification. In particular, these limitations can cause development periods and costs to increase, and the reliability of environmental conditions is lacking due to non-standard modules. The test equipment of the proposed PXIe platform can use diverse COTS modules to shorten the development period and minimize the instability between developments. The PXIe development module works with standard Xilinx FPGAs, PXIe Windows device drivers, and applications on standard PXIe buses. The use of standard bus and COTS modules increases scalability and reusability, enabling rapid development and excellent maintenance. Through the test, we show the proposed test equipments can be implemented efficiently between the development processes and proved their reliability through function tests and environmental tests.

• Journal of Digital Convergence
• /
• v.8 no.4
• /
• pp.19-33
• /
• 2010

As one of the most traffic devices, bus has played a great role in Korea for the last years. However, a great many peoples in big cities have continually decreased with the increase of private car ownership. It causes lower quality of bus service and unstability of operation in many bus companies. In the several local government, the operation system of bus was changed to Bus Quasi-Public Operating System. The aim of this study is to assess the effects and to suggest improvement strategies of Bus QPOS. According to the results of the analysis, Bus QPOS has brought various positive effects, but it has occurred negative effects, especially a much increase of government subsidies to bus company. To resolve a negative effects, government should examine the whole condition of bus operations. This study suggests strategies to improve Bus QPOS, which is including transparency of management, fair assessment system, standard cost system for bus operations.

• Journal of Auto-vehicle Safety Association
• /
• v.13 no.3
• /
• pp.47-53
• /
• 2021

This study is a study to estimate the VSL (Value of a Statistical Life) and CBA (Cost-benefit analysis) of the rollover safety standard for hydrogen buses, VSL is an economic value concept used to quantify the benefits of avoiding death. CBA shows the effect of cost-benefit, and if B/C is greater than 1, there is a social effect. In order to estimate the VSL and CBA, the hydrogen bus introduction scenario was assumed to be optimistic (20,000 vehicles in 2030), neutral (15,000 vehicles in 2030), and pessimistic (10,000 vehicles in 2030), and the effect of reducing human casualties was estimated. As a result, except for the pessimistic market situation of introducing hydrogen buses (10,000 vehicles in 2030) and the VSL reduction ratio of 10%, all policies were judged to have high cost-benefit effects. These results indicate that the introduction of the rollover safety standard for hydrogen buses is a socially effective policy.

• Journal of Aerospace System Engineering
• /
• v.15 no.6
• /
• pp.50-58
• /
• 2021

Byteflight is developed based on RS-485 communication (an international standard), and it can be used as a data bus during the operation of an integrated avionics system in the latest aircraft. Therefore, the integrated avionics system can perform an effective and safe flight mission only when the accurate and seamless display of flight information, communication, and accurate functions of navigation are implemented. In this study, cause analysis and failure investigation were performed on screen abnormalities and communication interruptions due to signal interference in the Byteflight data bus of the integrated avionics system during aircraft operation. To improve signal interference between avionics units, the branch point and wiring path of the Byteflight data bus were changed, and the verification result of the improved method was also described.