• 소성∙가공
• /
• 제16권6호
• /
• pp.457-462
• /
• 2007

The drawbeads, which are used for controlling the flow of the sheet into die cavity by imposing the tension and for preventing the forming defects like wrinkling, springback, etc. during the sheet forming process, affect the formability strongly because of the differences in the restraint and opening forces according to the drawbead shapes and dimensions. In this study, the experimental device enabling to measure the drawbead restraining and opening forces is manufactured and the drawing forces of circular, square, and step drawbeads are measured. The drawbead restraining and opening forces of a circular drawbead are increased as its drawbead height is increased. Similarly, those of a square drawbead are increased as its height is increased and shoulder radii decreased. The drawbead forces obtained from the experiment were compared with those calculated in the numerical simulation of stamping process of automotive fender. Good agreement was found so that the experimental measurements can be used in the simulation of auto-body stamping process.

• 한국정밀공학회지
• /
• 제27권5호
• /
• pp.75-84
• /
• 2010

The aim of this paper is to design the blank shape of SPFH 590 high strength steel for stamping of the center hinge of automotive via numerical analyses and experiments for multi-stages transfer forming process. Three-dimensional elasto-plastic finite element analyses for the transfer forming process with six stages were performed using a commercial code AUTOFORM V4.2. The influence of the blank shape on the formability and the shape conformity were quantitatively examined through the FE analyses. From the results of the FE analysis, a feasible shape of the blank and the forming load were estimated. Stamping experiments were carried out using the proposed blank shape. The results of experiments were shown that the center hinge parts with the desired shapes can be manufactured successfully as the proposed blank shape is used. Through the comparison of the results of the experiments with those of the analyses, it was shown that the estimation of blank shape using the FE analysis is a proper methodology to create a feasible shape of the blank for the center hinge of automotive.

• 한국산학기술학회논문지
• /
• 제19권8호
• /
• pp.25-31
• /
• 2018

본 연구에서는 카울 모듈의 성형 시 최적 설계 공정을 유한요소해석을 통해 도출하는 방안을 제시하였다. 소재 인장시험 및 성형성 평가와 같은 기계적 물성 평가를 통해 성형 해석의 주름 및 크랙 발생을 사전에 파악하고 이를 개선하기 위한 공정 설계 변경을 통해 최적 설계 방안을 도출하였다. 또한 제진성 향상이 필요한 카울 로워 패널에 패치워크를 적용을 통해 카울 모듈의 강성 증대 및 제진 특성 향상을 고유진동수 측정 시험과 해석을 통해 확인하였다. 해석 결과, 실러 패치워크 기술 적용에 따른 1차 고유진동수가 향상됨을 알 수 있었고, 이는 강성 및 제진특성 증대와 관련있다고 볼 수 있다. 실러 패치워크 적용 시 공정수 감소를 위해 성형 전 로워 패널 블랭크에 패치워크 블랭크를 점용접으로 접합시켜 성형하므로, 성형 후 패치워크 패널의 위치가 점용접 조건에 따라 달라진다. 이를 위해 점용접 위치에 따른 성형 해석을 실시하여 결과를 바탕으로 최적 공정 설계를 도출하였다. 스탬핑 공법을 이용한 타부품의 적용을 위해 성형 해석 기법을 구축하여 다양한 제품 설계에 도움이 될 것으로 판단된다.

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.64-76
• /
• 1997

This paper deals with development of brackets by using aluminum alloy sheets which is indispensable for weight reduction of autobody. The press formability of aluminum alloy sheet is estimated by means of tensile test, V bending test, sample manufacturing test and photograph of microstructure. The results show that the elongation, strength, work hardening exponent, plastic anisotropy coefficient of Al 6***series are better than those of Al 5***series, but for general press formability, Al 5***series are better than Al 6***series due to lower yield strength. Since most of mechanical properties of aluminum sheet are generally inferior to those of cold-rolled steel sheet, shape fixability and press formability of aluminum sheet are very poor. For making components of autobody by use of die for steel sheet application, it is essential that die should be nodified for least bending and stretching. With the modified die for aluminum, it could be possible to make brackets, the component of autobody. Microstructure of Al 5***series has fine grain and small the 2nd phase and that of Al 6***series has relatively coarse grain. Therefore, it seems that fine grain and small the 2nd phase of Al 5***series is one of the factor of lower yield strength, resistance to stamping work, formation of Luder's line.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.431-433
• /
• 2007

The drawbeads, which is used for controlling the flow of the sheet by imposing the tension and for preventing the springback in the sheet metal forming process, affects a lot the formability because of the differences in the restraint and opening forces according to the drawbead shapes and dimensions. In this study, the experimental device enabling to measure the drawbead restraining and opening forces was manufactured and the drawing forces of circular, square, and step drawbeads are measured. The drawbead restraining and opening forces of a circular drawbead are increased as its drawbead height is increased. Similarly, those of a square drawbead are increased as its height is increased and shoulder radii decreased. Also, those of a step drawbead are increased as its height and difference in their heights are increased.

• 소성∙가공
• /
• 제24권5호
• /
• pp.354-360
• /
• 2015

AHSS (Advanced High Strength Steels) has been increasingly employed by global automotive OEMs in order to satisfy strengthened regulations and reduce weight for fuel efficiency. Hot stamping using boron steels in AHSS increases not only formability but also strength. The typical hot-stamped automotive part is the center pillar that is critical for vehicle side impact. However, the hot-stamped part can be risky for the passenger safety caused by brittle fracture under a vehicle collision. The high power diode laser is suitable for the heat treatment giving AHSS increased elongation that prevents brittle fracture in car crash. Therefore, local softening by laser heat treatment for energy absorption area on the hot-stamped part improves crash-worthiness.

• 대한기계학회논문집A
• /
• 제32권10호
• /
• pp.890-896
• /
• 2008

Sheet metal forming is one of the most useful and important method in manufacturing of the autobody panels because of the excellent production rate. The objectives of sheet metal forming processes are getting a desired geometrical shape of products with good quality, low cost and reasonable lead time. In this paper, we examined the validity of finite element method analysis on the automobile FRT-PLR-L/R stamping process by using the lancing engineering method. Lancing is a press operation in which a single-line cut or slit is made on part way across the strip stock, without removing any metal. As a result, it has shown that the proper lancing engineering method could prevent fracturing by improving sheet metal flow.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2011년도 춘계학술대회 및 Fine pattern PCB 표면 처리 기술 워크샵
• /
• pp.207-207
• /
• 2011

The numerical simulation of the Forming Limit Diagram(FLD) test was carried out to calculate the limiting dome height(LDH: ISO12004-2) for aluminum alloy sheet Al6061-T6. The finite element analysis was used as an effective method for evaluating formability and diagnosing possible production problems in sheet stamping operations. To predict fracture during the stamping process, several failure models such as Cockcroft-Latham, Rice-Tracey, Brozzo and ESI-Wilkins-Kamoulakos(EWK) criteria were applied. The predicted results were discussed and compared with the experiments for Al6061-T6.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.1807-1818
• /
• 1991

본 연구에서는 자동차용 Zn-Ni계 합금 전기도금 강판(electro Zn-Ni alloy coated steel sheet, EGN)에서 도금층 중의 Ni함량에 따른 금층의 표면특성이 마찰거 동에 미치는 영향과 윤활유 종류에 따른 Ni 함량별 마찰특성을 파악하여 최적 스탬핑 조건을 도출하는데 기여하고자 한다.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.2113-2122
• /
• 1994

The 3-D FEM analysis for simulating the stamping operation of planar anisotropic sheet metals with arbitrarily-shaped tools is introduced. An implicit, incremental, updated Lagrangian formulation with a rigid-viscoplastic constitutive equation is employed. Contact and friction are considered through the mesh-normal, which compatibly describes arbitrary tool surfaces and FEM meshes without depending on the explicit spatial derivatives of tool surfaces. The consistent full set of governing relations, comprising equilibrium equation and mesh-normal geometric constraints, is appropriately linearized. The linear triangular elements are used for depicting the formed sheet, based on membrane approximation. Barlat's non-quadratic anisotropic yield criterion(strain-rate potential) is employed, whose in-plane anisotropic properties are taken into account with anisotropic coefficients and non-quadratic function parameter. The planar anisotropic finite element formulation is tested with the numerical simulations of the stamping of an automotive hood inner panel and the drawing of a hemispherical punch. The in-plane anisotropic effects on the formability of both mild steel and aluminum alloy sheet metals are examined.