• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.331-337
• /
• 2010

This study compared the macro and micro electrochemical characteristics at the local area of welding metal on dissimilar welding parts for type 304 stainless steel (SS) and type 316L SS. The materials are used for double wall gas pipe of duel fuel engine for a ship. The various potentiodynamic experiments were performed several times in 10% ${H_2C_2O_2}{\cdot}{H_2O}$ solution using macro and micro methods, respectively. The micro electrochemical experiments conducted to resolve at local area on cross-section of dissimilar welding materials by micro-droplet cell device. The micro-droplet cell techniques can be used almost electrochemical experiments to resolve corrosion characteristics of the limited electrode area of the metallic surface between wetted spot of working electrode and tip of sharpened capillary tube. The results of macro electrochemical experiments show that resistance of active dissolution reaction at welding zone was high due to low current density by formation of passivation protection film at passive region. According to the micro electrochemical experiment, the corrosion current density of welding zone and bond zone were relatively high.

• 한국전기전자재료학회논문지
• /
• 제30권8호
• /
• pp.501-507
• /
• 2017

A unimorph piezoelectric cantilever generator with an interdigitated electrode (IDE) was developed for vibration energy harvester applications driven in the longitudinal mode. Hard lead zirconate titanate (PZT) ceramic with a high $Q_m$ of 1,280 was used as the piezoelectric active material. Ten PZT sheets produced by tape casting were laminated and co-fired with an Ag/Pd IDE at $1,050^{\circ}C$ for 2 h. The approximately $280{\mu}m$-thick co-fired PZT laminate with the IDE was attached to a stainless steel substrate with an adhesive epoxy for the fabrication of an IDE unimorph cantilever. Its energy harvesting characteristics were evaluated: an output power of $1.1{\mu}W$ at 120 Hz across the resistive load of $700k{\Omega}$ was obtained, corresponding to a normalized power factor of $4.1{\mu}W/(G^2{\cdot}cm^3)$.

• 한국정밀공학회지
• /
• 제18권12호
• /
• pp.152-158
• /
• 2001

In this paper, we have developed an electro discharge machine for micro drilling driven by a voice coil actuator. Because the voltage signal of the electro-discharging circuit shows a lot of peaks and valleys, the active type low-pass filtering technique is adopted to get the average of the signal. Since the motion of the voice coil is precisely controlled by the error value between the object voltage value and the measured one, it is possible to prevent the mechanical contact between the rotating electrode and the workpiece and to maintain the appropriate machining conditions during the process. The electro-chemical machining technology was also adopted to make small diameter electrodes. Pure water is used as a dielectric. The machining procedure is performed to verify the feasibility of the developed system. It takes about 10 seconds to drill the ${\phi}m$100${\mu}m$ hole to the 100${\mu}m$ thickness stainless steel plate. The machining time depends on the values of the resister and the capacitor. There may exist the optimal values of time constant and the tendency is displayed In the appendix.

• KEPCO Journal on Electric Power and Energy
• /
• 제1권1호
• /
• pp.175-180
• /
• 2015

본 연구에서는 간단한 화학적 합성 방법을 통하여 스테인레스 기판 위에 nano-bud 형태의 수산화 구리 박막을 형성하였다. 그리고 또 다른 합성 방법인 chemical bath deposition을 이용하여 수산화 구리 나노 구조를 간단하고 친환경적으로 형성하였다. 수산화 구리 박막의 구조적 연구는 X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) 방법을 통하여 이루어졌으며 다결정의 nano-bud 형상을 확인할 수 있었다. 또한 나노 구조로 합성된 수산화구리 전극의 전기화학적 측정은 1M KOH의 전해질 조건에서 cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD)에서 측정되었으며 $340Fg^{-1}$의 높은 비 용량을 보였다. 또한 $1mA\;cm^{-2}$ 의 전력 밀도에서 ${\sim}83Wh\;kg^{-1}$의 높은 에너지 밀도와 ${\sim}3.1kW\;kg^{-1}$의 높은 출력 밀도를 가지며 향상된 전극의 성능을 보였다. 이러한 뛰어난 의사 캐패시터의 성능은 수산화 구리의 nano-bud 형상에 의한 효과로 확인할 수 있었다. 본 연구를 통하여 화학적 합성 방법의 확장을 통하여 수산화 구리 전극의 에너지 저장 장치로써의 성능을 확인할 수 있었다.

• 한국미생물·생명공학회지
• /
• 제38권4호
• /
• pp.461-466
• /
• 2010

본 연구는 미생물연료전지를 이용하여 액비를 처리하고 동시에 유용한 전기에너지 발생이 가능한지를 실험한 것이다. 탄소섬유전극(graphite felt)와 스테인레스 스틸망을 다른 비율로 충진한 single-chamber 미생물연료전지를 이용하였으며 탄소섬유전극보다 스테인레스망을 더 많이 충진한 미생물연료전지를 대조구(CMFC)로 하여 탄소섬유전극이 더 많이 충진된 미생물연료전지(SMFC)와 서로 비교하였다. 농화 배양이 끝난 후, SMFC로부터 발생되는 전류는 $3.167{\pm}80\;mg/L$ 의 액비를 공급할 때 18 mA가 안정적으로 발생되었다. 이때 최대 전력밀도와 전류밀도는 각각 $680\;mW/m^3$와 $3,770\;mA/m^3$이었으며, CMFC의 전력밀도와 전류밀도보다는 높았다. 화학적산소요구량(COD)는 SMFC와 CMFC에서 $3.718{\pm}80\;mg/L$에서 $865{\pm}21$과 $930{\pm}14\;mg/L$로 감소하여 각각 72.7%와 70.6%가 감소되었다. SMFC와 CMFC로부터 부유물질(SS)은 99% 이상이 감소되는 것을 확인하였다. 또한 SMFC의 암모니아성질소, 질산성질소, 그리고 인산염인과 같은 영향물질 농도의 변화도 각각 65.4%, 57.5%, 그리고 73.7%이 감소되었으며 CMFC의 경우도 거의 유사한 제거율을 보였다. 이들 결과로부터 저가 재료가 충진한 미생물 연료전지를 이용함으로써 경제적 효과를 기대할 수 있음은 물론 가축분뇨로부터 적지만 전기 에너지가 발생하는 것을 확인할 수 있었다.

• The Korean Journal of Physiology
• /
• 제23권2호
• /
• pp.401-408
• /
• 1989

This study was conducted to investigate whether an electrical stimulation of medial amygdaloid nucleus in rats increases pancreatic secretion. And an involvement of vagus nerve or plasma secretin in this process was also studied. In fasting rats anesthetized with urethane, a monopolar stainless steel electrode was stereotaxically inserted into the right medial amygdaloid nucleus. Pancreatic juice was collected for 20 minutes, during which physiological saline or 0.01 N HCI (0.18 ml/min) was perfused into the duodenum with or without bilateral subdiaphragmatic vagotomy. In the medial amygdaloid group, an electrical stimulation was continuously applied to the medial amygdaloid nucleus during the perfusion period. After collection of pancreatic juice, blood was drawn from the abdominal aorta for determination of the plasma secretin level. The results were as follows: 1) The electrical stimulaion of the medial amygdaloid nucleus did not influence the pancreatic secretion in response to intraduodenal saline perfusion. 2) The stimulation of the medial amygdaloid nucleus significantly increased the pancreatic secretory response (volume, bicarbonate output) to the intraduodenal 0.01 N HCI perfusion, and the increases were abolished by vagotomy. 3) The plasma secretin concentration after the intraduodenal 0.01 N HCI perfusion was higher than that after the saline perfusion. However, neither the electrical stimulation of the medial amygdaloid nucleus nor vagotomy affected the plasma secretin concentration during the intraduodenal perfusion with saline or 0.01 N HCI. It is, therefore, suggested that the medial amygdaloid nucleus facilitates the pancreatic secretion (volume, bicarbonate) elicited by intraduodenal HCI perfusion through the vagus nerve.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권1호
• /
• pp.39-46
• /
• 2008

The end plates of fuel cell assemblies are used to fasten the inner stacks, reduce the contact pressure, and provide a seal between Membrane-Electrode Assemblies (MEAs). They therefore require sufficient mechanical strength to withstand the tightening pressure, light weight to obtain high energy densities, and stable chemical/electrochemical properties, as well as provide electrical insulation. The design criteria for end plates can be divided into three parts: the material, connecting method, and shape. In the past, end plates were made from metals such as aluminum, titanium, and stainless steel alloys, but due to corrosion problems, thermal losses, and their excessive weight, alternative materials such as plastics have been considered. Composite materials consisting of combinations of two or more materials have also been proposed for end plates to enhance their mechanical strength. Tie-rods have been traditionally used to connect end plates, but since the number of connecting parts has increased, resulting in assembly difficulties, new types of connectors have been contemplated. Ideas such as adding reinforcement or flat plates, or using bands or boxes to replace tie-rods have been proposed. Typical end plates are rectangular or cylindrical solid plates. To minimize the weight and provide a uniform pressure distribution, new concepts such as ribbed-, bomb-, or bow-shaped plates have been considered. Even though end plates were not an issue in fuel cell system designs in the past, they now provide a great challenge for designers. Changes in the materials, connecting methods, and shapes of an end plate allow us to achieve lighter, stronger end plates, resulting in more efficient fuel cell systems.

• 전기학회논문지P
• /
• 제63권4호
• /
• pp.373-377
• /
• 2014

A cross linked polyethylene (XLPE) material has been widely used to develop a distribution power cable due to its excellent electrical characteristics and mechanical strength. However, several problems such as environmental disruption, electrical aging, thermosetting property, and impurities which cause degradation also arise. Therefore, a novel dielectric material should be developed to substitute for the XLPE. Several kinds of polyolefin materials to substitute for the conventional dielectric material, XLPE are developed and A cylindrical rod to cylindrical rod electrode system made with stainless steel is used to perform the experiments according to the ASTM D-149 protocol under an AC and Impulse input voltage condition. The experimental results are calculated by the Weibull distribution method and analyzed by an Finite Element Method(FEM). Finally, the dielectric characteristics of the conventional XLPE and novel polyolefin are experimented compared with each other in this study.

• 전기학회논문지P
• /
• 제63권4호
• /
• pp.356-360
• /
• 2014

The environmental pollution caused by green-house gases such as $SF_2$ has been becoming the main issue of industrial society. As a part of these efforts, 180 countries signed the Kyoto Protocol in 1997 to cut back on their green-house gas emissions [1]. Therefore, a study on the dielectric characteristics of the $GN_2$ is important for designing a eco-friendly high voltage apparatuses. In this paper, to develop an electrically reliable, stable, and eco-friendly high voltage apparatus, the breakdown voltage and partial discharge inception voltage characteristics in $GN_2$ considering utilization factors are studied for the establishment of insulation design criteria of an high voltage apparatus. Dielectric experiments are performed by using several kinds of sphere-plane electrode systems made of stainless steel. Also, the dielectric characteristics of the $GN_2$ are analyzed by using a Finite Elements Method (FEM) according to various field utilization factors. The results are expected to be applicable to designing the high voltage apparatuses using $GN_2$ as an insulation gas.

• 실천공학교육논문지
• /
• 제6권2호
• /
• pp.105-110
• /
• 2014

본 연구에서는 강한 내구성을 지닌 자동차 타이어용 압력센서를 개발하기 위해 박막 물질로서 적용될 티타늄 멤브레인의 기계적 특성이 연구되었다. 제작공정으로 기존의 마이크로 머시닝공정과 적층 공정기술이 동시에 적용되었으며, 티타늄 멤브레인 기반의 압력 센서가 설계, 제조 및 특성화 되었다. 마이크로 머시닝 공정을 통한 티타늄 멤브레인과 기판의 접합 제조과정은 30분 동안의 20 MPa의 압력과 $200^{\circ}C$의 온도과정 후 $24^{\circ}C$에서의 냉각으로 진행된다. 각각의 압력센서 표면은 니켈 도금된 후방전극이 기판 위에 마이크로 소자로 조립되었다. 제작과정에서 발생한 잔류응력을 예측하기 위해 유한요소 해석이 적용되었다. 또한 티타늄 멤브레인의 외부 압력하에서 변형에 의한 처짐이 계산되었다. 제작된 장치의 민감도는 $10.15ppm\;kPa^{-1}$ 였고 이때의 정전용량 변화량은 0.18 pF, 압력 범위는 0-210 kPa 였다.