• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.24-30
• /
• 2004

As the environmental pollution becomes serious global problem, the regulation of emission exhausted from automobiles is strengthened. Therefore, it is very important to know how to reduce the NOx and PM simultaneously in diesel engines, which has lot of merits such as high thermal efficiency, low fuel consumption and durability. By this reason, the new concept called as Homogeneous Charge Compression Ignition(HCCI) engines are spotlighted because this concept reduced NOx and P.M. simultaneously. However, there is trade off between output and NOx in a HCCI engine. In this study, output and emission characteristics for a gasoline direct injection type HCCI engine were investigated to clarify the effects of intake air temperature, injection time and mixture formation. From these experiments, we found that the smoke was not produced when the fuel was injected earlier than BTDC 90$^{\circ}$. In addition, the output was increased because of delay of ignition time and NOx emission was decreased because of homogeneous charge of first injection in case of split injection.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권4호
• /
• pp.462-472
• /
• 1999

De-NOx facility using Selective Catalytic Reduction method is the most widely applied one that removes NOx from flue gas emitted from combustion facility such as boiler for power generation engine incinerator etc. Reductant $NH_3\;or\;NH_4OH$ is sprayed into flue gas to convert NOx into $H_2O$ and $N_2.$ Good mixing between flue gas and $NH_3$ is the most important factor to increase reduction in catalytic layer and to reduce unreacted NH3 slip. Therefore the development of mixer device for mixing effect is one of the important part for SCR facility. Objectives of this study are to investigate the relation between flow and concentration field by observation at the wake of delta-wing type mixer. At the first stage qualitative measurement of flow field is conducted by flow visualization using laser light sheet in lab. scale wind tunnel. Also we have conducted the quantitative analysis by comparing flow field measurement using LDV with numerical simulation. On the basis of qualitative and quantitative analysis we investigate the dis-tribution of flow and concentration in flow model facility. The results of an experimental and compu-tational examination of the vortex structures shed from delta wing type vortex generator having $40^{\circ}$ angle of attack are presented, The effects of vortex structure on the gas mixing is discussed, too.

• 항공우주기술
• /
• 제5권2호
• /
• pp.102-107
• /
• 2006

본 논문은 위성체 동적 환경의 발사체 구조에 의해 전달된 저 주파수의 과도 진동과 불 규칙적인 가속력으로 구성되어 있다. 저 주파수에서의 과도 진동은 보통 진동수 100 ~ 200Hz에 이르는 정현파로 근사되며 주로 예비설계에 사용된다. 그리고, 랜덤 환경은 발사체의 연소와 분리 단계, 외부 공력소 음에 의한 구조적 진동에 의해 발생한다. 이는 발사체 구조물을 통하여 위성체와 발사체의 어댑터 구조로 전달된다. 이러한 동적환경 중에서 랜덤 진동 해석은 위성체에 수행되는데, 특히, 위성체 내의 전자 박스(장비) 는 실제 상황에 가깝게 하여 검증하기 위해 랜덤 진동 실험을 통해 설계 되야 한다.

• Coupled systems mechanics
• /
• 제1권3호
• /
• pp.285-295
• /
• 2012

In this paper, two types of porous burners with radial and axial flow have been modeled numerically and compared. For this purpose, governing equations were solved one-dimensionally for methane-air premix gas. The mechanism used in simulating combustion phenomenon was 15 stage reduced mechanism based on GRI3.0. In order to compare the two burners, the inlet flow rate and fuel-air ratio have been assumed equal for the two burners. The results of the study indicated that reduction in speed and increase in cross-section area in the direction of flow have a considerable influence on the behavior of radial burner in comparison to axial burner. Regarding temperature distribution inside the burner, it was observed that the two above mentioned factors can be influential in temperature of flame propagation region. Also, regarding distribution of CO and NO emission, the results indicate that the porous radial burner has lower emissions in comparison to the axial once. The output radiative heat transfer efficiency of the two burners was also compared and in this case also even the radial porous burner was found to be preferable.

• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.47-52
• /
• 2016

Miller timing is one of the promising ways which can improve the fuel consumption of internal combustion engines. Indeed, Miller timing employing an early intake valve close is widely applied to large diesel and gas engines to enhance performance and reduce NOx emissions. In this study, performance evaluation is carried out by 1-D cycle simulation in order to estimate the effect of Miller CAM timing before BDC for a 32 L turbocharged diesel engine. To optimize Miller CAM timing, a single stage turbocharger is matched with an early intake valve close since boost pressure is a significant parameter that can control compression work in a turbocharged engine. The engine simulation result shows that there is enough potential to improve fuel consumption rate and also reduce NOx emissions at the same time.Abstract here.

• 한국재료학회지
• /
• 제24권5호
• /
• pp.249-254
• /
• 2014

Due to their unique properties, tungsten borides are good candidates for the industrial applications where certain features such as high hardness, chemical inertness, resistance to high temperatures, thermal shock and corrosion. In this study, conditions were investigated for producing tungsten boride powder from tungsten oxide($WO_3$) by self-propagating high-temperature synthesis (SHS) followed by HCl leaching techniques. In the first stage of the study, the exothermicity of the $WO_3$-Mg reaction was investigated by computer simulation. Based on the simulation experimental study was conducted and the SHS products consisting of borides and other compounds were obtained starting with different initial molar ratios of $WO_3$, Mg and $B_2O_3$. It was found that $WO_3$, Mg and $B_2O_3$ reaction system produced high combustion temperature and radical reaction so that diffusion between W and B was not properly occurred. Addition of NaCl and replacement of $B_2O_3$ with B successfully solved the diffusion problem. From the optimum condition tungsten boride($W_2B$ and WB) powders which has 0.1~0.9 um particle size were synthesized.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.52-57
• /
• 2012

액체로켓은 연소기, 가스발생기, 터보펌프, 터빈 등으로 구성된 시스템이며, 각 요소들을 연결해주는 공급계 부품들로 구성되어 있다. 각 부품들이 액체로켓 성능에 복합적인 영향을 미치기 때문에 개념설계 전 시스템의 전체적인 예비해석이 반드시 필요하다. 액체로켓 엔진 시스템의 각 구성품 모듈을 고려한 통합 해석 프로그램의 개발은 이루어지지 않았다. 본 논문에서는 액체로켓 공급계 부품의 모델구성 및 검증을 거친 후 가스발생기 사이클 구성하였으며, 대표적인 가스발생기 사이클인 F-1 엔진의 결과와 비교하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.96-99
• /
• 2012

로켓 추진기관 시스템의 성능을 입증하기 위한 시험설비는 로켓시스템의 개발을 위한 필수 인프라이다. PSTC는 발사체의 각 단별 추진기관 시스템의 수류시험 및 연소시험을 수행하고, 발사 프로세스에 대한 지상검증을 수행한다. PSTC 개발을 위해 국내외 기술을 조사하여, 관련분야의 사례를 적극 활용한다. 추진기관 시험설비는 유공압 시설 및 제어계측, Test Stand, 화염유도로 등을 구성한다.

• 한국추진공학회지
• /
• 제23권2호
• /
• pp.87-94
• /
• 2019

액체로켓 추진기관 시험설비는 시험대상체가 상위 시스템에 장착되었을 때의 인터페이스 조건을 모사하여야 하며, 시험 시 파손이 발생할 수 있는 개발품의 특성상, 안전하게 시험이 이루어질 수 있게 구축되어야 한다. 이를 위해 추진기관 시험설비 기반시설은 안정적인 연소가 이루어지고 사고 시에도 안전이 보장되도록 구축되어야 한다. 본 논문에서는 액체로켓 엔진 추진기관 시험설비 기반시설의 구축 및 운영 시 고려해야 할 사항에 대해, 토목/건축, 시험 스탠드, 설비의 배치, 타 설비와의 운영 조합 및 공동구, 소화설비, 전력설비 측면에서 고찰하였다.

• 한국추진공학회지
• /
• 제25권2호
• /
• pp.79-87
• /
• 2021

본 연구에서 축 방향으로 충전 된 이종 추진제를 적용 이중 추력 추진기관의 성능 예측/해석 방법을 개발하였다. 부스터로부터 서스테이너 단계로 천이될 때 계면에서 성능에 관한 과도현상이 발생하였는데, 그 과도현상의 원인과 특성을 연소시험 결과와 함께 비교하여 조사하였다. 성능과도 현상은 추진제 물성이 서로 다른 추진제 사이 형상설계뿐만 아니라, 추진제 경화 수축에 따른 제작상 오차에 의해 민감하게 발생되고 있음을 확인되었다.