• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Journal of Periodontal and Implant Science
• /
• 제29권3호
• /
• pp.483-509
• /
• 1999

Biodegradable barrier membrane has been demonstrated to have guided bone regeneration capacity on the animal study. The purpose of this study is to evaluate the effects of cultured calvarial cell inoculated on the biodegradable barrier membrane for the regeneration of the artificial bone defect. In this experiment 35 Sprague-Dawley male rats(mean BW 150gm) were used. 30 rats were divided into 3 groups. In group I, defects were covered periosteum without membrane. In group II, defects were repaired using biodegradable barrier membrane. In group III, the defects were repaired using biodegradable barrier membrane seeded with cultured calvarial cell. Every surgical procedure were performed under the general anesthesia by using with intravenous injection of Pentobarbital sodium(30mg/Kg). After anesthesia, 5 rats were sacrificed by decapitation to obtain the calvaria for bone cell culture. Calvarial cells were cultured with Dulbecco's Modified Essential Medium contained with 10% Fetal Bovine Serum under the conventional conditions. The number of cell inoculated on the membrane were $1{\times}10^6$ Cells/ml. The membrane were inserted on the artificial bone defect after 3 days of culture. A single 3-mm diameter full-thickness artificial calvarial defect was made in each animal by using with bone trephine drill. After the every surgical intervention of animal, all of the animals were sacrificed at 1, 2, 3 weeks after surgery by using of perfusion technique. For obtaining histological section, tissues were fixed in 2.5% Glutaraldehyde (0.1M cacodylate buffer, pH 7.2) and Karnovsky's fixative solution, and decalcified with 0.1M disodium ethylene diaminetetraacetate for 3 weeks. Tissue embeding was performed in paraffin and cut parallel to the surface of calvaria. Section in 7${\mu}m$ thickness of tissue was done and stained with Hematoxylin-Eosin. All the specimens were observed under the light microscopy. The following results were obtained. 1 . During the whole period of experiment, fibrous connective tissue was revealed at 1week after surgery which meant rapid soft tissue recovery. The healing rate of defected area into new bone formation of the test group was observed more rapid tendency than other two groups. 2 . The sequence of healing rate of bone defected area was as follows ； test group, positive control, negative control group. 3 . During the experiment, an osteoclastic cell around preexisted bone was not found. New bone formation was originated from the periphery of the remaing bone wall, and gradually extended into central portion of the bone defect. 4 . The biodegradable barrier membrane was observed favorable biocompatibility during this experimental period without any other noticeable foreign body reaction. And mineralization in the newly formed osteoid tissue revealed relatively more rapid than other group since early stage of the healing process. Conclusively, the cultured bone cell inoculated onto the biodegradable barrier membrane may have an important role of regeneration of artificial bone defects of alveolar bone. This study thus demonstrates a tissue-engineering the approach to the repair of bone defects, which may have clinical applications in clinical fields of the dentistry including periodontics.

• Tuberculosis and Respiratory Diseases
• /
• 제44권1호
• /
• pp.69-84
• /
• 1997

배경 : 폐암은 13%만이 완치할 수 있는 예후가 불량한 질환으로 조기진단이 중요한 것으로 알려져 있다. 상피내암이나 미세침윤성 기관지암 등의 조기폐암은 조기에 효과적으로 치료할 수 있어 그 진단이 중요하며, 최근에는 전구암 병변도 조기에 진단 가능하므로써 그 예방적인 치료가 시도되고 있다. 조기진단을 위한 객담 세포진 검사나 기존의 기관지 내시경검사는 조기폐암과 전구암 병변에 대한 진단율이 떨어져 진단에 어려운 실정이다. 최근에는 정상과 암세포의 자기형광 (autofluorescence)을 이용한 형광 기관지 내시경(lung imaging fluorescence endoscope device : LIFE)을 통하여 조기 폐암과 전구암 병변의 진단에 효과적인 것으로 알려져 있다. 목적 : 본 연구는 기존의 내시경을 시행하는 환자를 대상으로 형광기관지 내시경 검사를 시행하여 기관지 점막에 이상이 있는 경우 조직검사를 통하여 두 검사 사이에 민감도와 특이도의 차이를 비교하였다. 방법 : 대상환자는 총 35명으로 평균연령 59.3(27-77)세였으며, 남자 26명, 여자 9명이었다. 흉부 방사선상에 폐암 환자 9명, 폐구엽성 무기폐환자 4명, 폐렴환자 3명, 객담에서 악성세포 양성을 보인 2명, 원인 모르는 흉수 환자 2명, 혈담환자 9명, 만성 기침환자 6명이였다. 대상환자 중 악성종양으로 진단된 환자는 15명이였으며, 기존의 백색빛 광원의 기관지 내시경검사와 형광 기관지 내시경 검사를 시행하였으며, 두 검사에 중에 한 검사에서도 이상병변이 있는 경우 조직검사를 시행하여 총 79조직을 얻어 두 검사간에 민강도와 특이도를 비교하여 다음과 같은 결과를 얻었다. 결과 : 1) 총 79조직은 정상조직이 8, 상피세포 증식이 21, 상피세포의 이형성이 23, 침윤성 폐암이 27조직이었다. 2) 상피세포의 이형성인 23조직에서 백색빚 기관지내시경은 14조직에서 양성으로 60.9 % 였으나, LIFE는 19조직에서 양성으로 82.6 %로 높은 경향을 보였다. 3) 27조직의 침윤성 폐암에 대한 백색빛 기관지내시경는 27조직 모두 양성(100%)인 반면에, LIFE는 19조직이 양성으로 70.3 %의 양성율을 나타냈다. LIFE에서 음성으로 보인 8조직의 침융성 폐암은 선암 7조직 중 3조직, 소세포암 8조직 중 5조직이었으며, 이들은 모두 상피조직은 정상이나 암조직이 점막이하에 침윤되어 있었던 조직이었다. 반면에 상피조직에 이상이 있던 7조직의 편평상피 세포암 조직, 1조직의 대세포암, 2조직의 유암과 2조직의 전이성 앙은 모두 양성이었다. 결론 : 이상의 결과로 LIFE는 전구암 병변과 기관지 기관지 폐암증에 상피세포에 이상이 있는 기관지 폐암의 진단에는 백색빛 기관지내시경보다 민감도가 높아 기관지 상피세포에 이상이 있는 전구암 병변과 조기폐암에는 유용할 것으로 사료되나, 기관지 폐암중에 정상의 기관지 점막하에 칩윤하는 기관지 폐암의 진단에는 한계가 있을 것으로 사료된다.

• 한국가금학회지
• /
• 제33권3호
• /
• pp.171-179
• /
• 2006

이 연구는 한국 재래 닭에서 부화 후 고환 발달 과정을 명확하게 이해가기 위하여 부화 후 1, 2, 4, 6, 8, 10, 12, 14, 16, 18, 21, 28, 32, 44, 52 및 64주령(n=13마리/일령)의 한국 재래닭을 이용하여 수행하였다. 한국 재래 닭의 고환은 2.5 % glutaraldehyde를 이용하여 전신 관류 고정하고 조직 처리 과정을 거쳐 Epon-araldite에 포매하였다. 초박절편기를 사용하여 $1{\mu}m$로 절편한 다음 methylene blue로 염색하여 일반적인 조직의 변화상과 형태 계측을 일반적인 방법에 따라서 정자 생성을 측정하여 다음과 같은 결과를 얻었다. 부화 후 1주령의 고환의 평균 무게는 0.015 g이었고 점진적으로 증가하여 21주령에는 3.93 g이고 21주령부터 64주령까지는 변화가 없었다. 곱슬정세관의 용적 치밀도는 1주령에 32.6%이었으나 점차적으로 증가하여 64주령에서는 92.89이었다. 1주령의 한국 재래 닭 고환 간질 조직은 고환 실질의 67.4%를 나타내었고 이러한 비율은 성장하는 동안에 점차적으로 감소하여 64주령에 7.11%를 나타내었다. 고환내 총 정자 생성은 18주령부터 28주령까지는 유의성있게 증가하였고 고환 1g당 정자 생성은 $18\sim28$주령까지는 유의성있게 증가하였고 $28\sim52$주령까지는 변화가 없었으나 64주령에 유의성 있게 감소하였다. 곱슬정세관의 평균 직경은 $1\sim21$주령까지 주령에 따라 점진적으로 증가하였고 곱슬정세관의 길이는 1주령에 0.34 m이었고 성장하면서 유의성 있게 증가하여 64주령에서는 72.2 m이었다. 곱슬정세관내 생식세포의 발달 단계는 다음과 같이 분류할 수 있다. 1) 정조세포($1\sim8$주령), 2) 정조세포, 정모세포($10\sim12$주령), 3) 정조세포, 정모세포, 원형의 정자세포($14\sim16$주령), 4) 정조세포, 정모세포, 정자세포 및 정자($18\sim64$주령). 이러한 결과를 종합하여 보면 한국 재래 닭에서 부화 후부터 성숙시기까지 고환 발달의 양상은 신생시기-성 성숙 이전기($1\sim12$주령), 성 성숙시기($14\sim18$주령) 및 성숙시기$(21\sim64)$로 나뉜다.

• Tuberculosis and Respiratory Diseases
• /
• 제56권5호
• /
• pp.465-484
• /
• 2004

배 경 : 인슐린 양 성장 인자(IGF) 결합 단백질-3(IGFBP-3)은 IGF와 결합하여 IGF의 세포 분열 촉진 및 항세포 고사 기전을 억제할 뿐 아니라 IGF와는 독립적으로 세포고사를 유도함으로써 비소세포성 폐암 세포주의 성장을 억제한다. 방 법 : 본 연구에서 저자들은 IGFBP-3 promoter의 hyper-methylation이 IGFBP-3 단백 발현에 어떠한 역할을 하는가를 연구하였다. 또한 비소세포성 폐암 세포주에서 methylation된 IGFBP-3 promoter에서 유전자 발현을 억제하는 기전을 연구하였다. 결 과 : 본 연구에 사용된 15 종의 비소세포성 폐암 세포주 중 7종 (46.7%)에서 IGFBP-3 promoter의 methylation 이 관찰되었으며, 23명의 I기 환자 검체 중 16 (69.7%), 9명의 II기 환자 검체중 7 (77.8%), 5명의 IIIA 환자 검체중 4 (80%), 6명의 IIIB 환자 검체중 4 (66.7 %), 그리고 6 명의 IV기 환자검체중 6명 모두에서 (100%) promoter 의 methylation 이 관찰되었다. 이 비소세포성 폐암 세포주에서 promoter methylation 상태는 IGFBP-3 단백 및 mRNA 발현양상과 잘 일치하였으며, IGFBP-3의 발현이 억제되었던 비소세포성 폐암 세포주들 중 일부의 세포에서 demethylating 약제인 5'-aza-2'-deoxycytidine (5'-aza-dC) 처리 후 그 발현이 회복되었다. IGFBP-3 promoter 활성도에 중요한 역할을 하는 Sp-1/Sp-3 결합 요소는 IGFBP-3 단백 발현이 억제된 비소세포성 폐암 세포주에서 methylation되어 있었으며, 이 요소의 methylation 은 Sp-1 전사 인자의 결합을 억제하였다. ChIP assay 결과에서 IGFBP-3 promoter의 methylation 상태는 Sp-1/Sp-3 결합 요소에 Sp-1, methyl-CpG binding protein-2 (MeCP2), 그리고 histone deacetylase (HDAC)의 결합에 영향을 주며, 이는 5'-aza-dC 처리에 의하여 역전 되었다. Sp-1/Sp-3 결합 요소를 포함하고 있는 IGFBP-3 promoter의 in vitro methylation은 promoter activity를 현저히 감소시켰으며 이는 MeCP2 단백을 동시에 발현 시켰을 때 더욱 억제되며 5'-aza-dC 처리시 회복되었다. 결 론 : 이러한 결과들은 IGFBP-3 promoter의 methylation이 IGFBP-3 발현을 억제하는 하나의 기전이며, HDAC의 모집을 유도함으로서 MeCP2가 IGFBP-3 발현 억제에 중요한 역할을 함을 보이는 것이다. 이런 현상은 비소세포성 폐암에서 진단 당시의 진행된 병기와도 관계가 있어 IGFBP-3 promoter의 methylation 상태가 비소세포성 폐암의 발암 기전 및 진행에 중요한 역할을 하고 있음을 보이고 있으며, 나아가 조기 진단 및 암 예방영역에서 하나의 생물학적 지표로도 사용될 수 있을 것으로 생각된다.

• 한국작물학회지
• /
• 제5권1호
• /
• pp.1-35
• /
• 1969

I. 강원도 춘천지방에서 주로 재배되는 수도 품종 20개를 공시재배하여 출수기에 신장절위(간선단으로부터 4 개절위)경엽에 대한 형태조사를 한 바 그 결과는 다음과 같다. 1. 공시한 20 개품종의 평균엽면적은 제 1 엽 18.61 $cm^2$, 제 2 엽 21.84 $cm^2$, 제 3 엽 21.52 $cm^2$, 제 4 엽 18.56 $cm^2$로서 제 2 엽과 제 3 엽이 크고 제 1 엽과 제 4 엽이 작았으며 엽신중은 제 1 엽 97.0 mg, 제 2 엽 118.1 mg, 제 3 엽 115.4mg, 제 4 엽 95.3 mg로서 엽위별의 비중은 전기 엽면적의 경우와 같았고 엽초중(절당)은 제 1 엽초 176.3 mg, 제 2 엽초 163.7 mg, 제 3 엽초 163.4 mg, 제 4 엽초 123.9 mg 로서 절위가 상승함에 따라 현저히 컸다. 또한 엽중(엽신+엽초)은 절위당 제 1 엽 273.3 mg, 제 2 엽 281.8 mg, 제 3 엽 278.8 mg, 제 3 엽 219.1 mg로서 엽위별의 제2 및 제3엽이 컸고 제1엽과 제4엽이 적었으며 고간중(엽신+엽초+간)은 제1절위 374.4 mg, 제2절위 418.2 mg, 제3절위 446.1mg 및 제4절위 362.1 mg로서 역시 중간절위가 크고 상위와 하위에서 적었다. 2. 신장 절위 경엽의 품종간 변이계수를 산출하여 본즉 엽면적에 있어서 12.75%, 엽신중 15.29%, 엽초중 15.90%, 절간중 11.42%, 엽중(엽신중+엽초중) 15.45% 그리고 엽중 13.24%였으며 각절위에 있어서 엽면적, 엽신, 엽초, 간중등의 품종간 변이계수는 간중을 제외하고는 모두 제2 및 제3절위에 있어서 작았고 제3 및 제4절위에서 컸으며 절간중에 있어서는 제3 및 제4절위의 변이계수가 작았다. 그리고 각 절위간 경엽의 변이계수는 엽면적 8.90%로서 가장 적고 엽신중 11.24%로서 적은 편이었으며 간중은 20.02%로서 가장 컸다. 3. 수도의 엽간중에 대하여 엽신 엽초 및 절간이 각각의 고유하는 중량의 비율은 29.2%로서 가장 높고 간중 34.2%, 엽신중 26.6%로서 낮으며 각 절위에 있어서도 각 부분이 점유하는 비율은 대체로 같은 경향이지만 엽신중의 비중은 제2엽에서 크고 엽초중은 상위절에 갈수록 간중은 반대로 하위절일수록 비중이 높았다. 4. 4개절위를 합한 엽신/간비는 77.7%, 엽초/간비 114.5%, 엽신/엽초비 67.9% 및 엽신/간+엽초비 36.2%이며 상위벌에서 엽신/간비 및 엽초/간비는 높고 엽신/엽초비는 하위절에서 높았다. 5. 수도의 신장 절위 경엽과 수량과의 관계는 전체엽면적의 4개엽과 정조수량과의 상관관계(r)는 0.666이었고 제1엽 및 제2엽은 0.659 및 0.609로서 각각 고도의 정(+)의 상관을 보였으며 제3엽과 제4엽은 0.464, 0.523으로서 유의상관을 인정하였으며 전체엽신중과 정조수량간에는 0.678, 제1엽 0.691, 제2엽 0.654, 제3엽 0.570으로서 각각 고도의 정(+)의 상관을 보였고 제4엽에 있어서는 0.544로서 유의상관을 보였으며 엽중(엽신중+엽초중)과 수량과의 상관은 엽면적의 경우와 동일한 경향을 보였고 엽간중과 수량과의 상관은 총고간중 및 제1절위고간중에서만 고도의 정(+)상관을 보였고 그 밑에 절위에서는 유의상관을 보였다. 한편 전체엽초중과 정조수량간에 있어서는 0.572, 제1엽초 0.623으로서 각각 고도의 정(+)상관을 보였고 제2, 제3 및 제4엽초에 있어서는 각각 0.486, 0.513 및 0.450 으로서 유의상관을 보였고 간중과 정조수량과의 상관은 모두 0.377 이하로서 낮은 상관을 보였다. 6. 수량계급에 따르는 품종들의 신장 절위 경엽의 평균치로 본 엽신중, 엽면적 1 $cm^2$당 엽신중, 엽초중, 간중, 엽중은 모두 다수품종에서 컸으며 중수>소수품종의 순위로 낮았고 각 절위별에 있어서도 대체로 같은 경향을 보였으며 그들에 있어서의 절위간변이는 엽면적, 엽신중, 엽초중, 간중 모두 다수품종에서는 현저히 적고 중수 및 소수품종에서 컸다. 7. 수량계급에 따르는 품종들의 식물체지상부 구성비율 즉, 엽신, 엽초, 엽간이 각각 점유하는 비율은 다수품종에 있어서 엽신 27.6% 엽초 39.5%, 간 32.9%인데 비하여 소수품종은 엽신 25.5%, 엽초 38.1%, 간 36.4%이고 중수품종은 그들 중간적 값을 보였다. 8. 수량계급에 따르는 품종들의 엽신/간비, 엽초/간비는 다수품종은 높고 소수품종은 낮았으며 중수품종은 그들 중간을 보였다. II. 수도품종 신 2 호, 시로가네 및 진흥의 3개를 공시하여 10a당 실소를 8kg, 12kg 및 16kg의 3개수준으로 시용하여 신장 절위 경엽의 형태변이를 조사하는 한편 잎의 실소함량을 분석하여 그들과 수량과의 관계를 살펴 본 결과는 다음과 같다. 1. 신장 절위 경엽의 시용량에 따르는 3개 품종의 평균형태변이치는 총엽면적(선단으로부터 4개엽 총합)은 실소 8kg구에 비하여 2배비에서 16.5%의 증대를 보였으며, 총엽신중에 있어서도 거의 같은 비율의 증대를 각각 보였고, 총엽초중에 있어서는 2개비구 7.8%, 1.5 개비구 4.9%의 증대를 보였고, 각엽위별에 있어서도 전자와 비슷한 경향을 보였다. 한편 간중은 반대로 2개비구 11.2%, 1.5개비구 1.5%씩 각각 감소되었으며, 그 정도는 특히 하위절위에서 현저하였다. 2. 각 품종의 신장 절위 경엽이 시비량에 따르는 변이계수는 총엽면적에 있어서는 제002 15.40%, 시로가네 12.87% 및 진흥 10.99%였고, 각 절위별로 엽신의 변이가 큰 것은 신 002는 제4엽, 시로가네는 제2엽, 진흥은 제1엽으로서 품종간에 차이가 있었다. 총엽신중의 변이계수는 총엽면적의 경우와 같은 경향을 보였고, 총간중의 변이계수는 제002 7.72%, 시로가네 12.11% 및 진흥 0,94% 이였으며 각 절위별 변이의 정도도 품종에 따라 다르다. 3. 신장 절위 경엽의 시비량에 따르는 절위간 변이는 엽면적, 엽신중, 간중 모두 N8kg인 소비조건에서 변이가 크고 N16kg인 다비조건에서 적어졌으며 N12kg구는 이들 중간이고, 엽초중에 있어서는 다비조건에서 변이가 컸다. 4. 엽초중을 구성하는 엽신 엽초 및 절간이 각각 점유하는 비율은 시비량에 따라 다르며, 시비량의 증가에 따라 엽신중의 비율은 현저히 높아지고, 엽초중의 비율은 반대로 낮아진다. 5. 시비량에 따르는 공시품종의 신장 절위 경엽의 상호관계를 보면 엽신/간비는 소비구에서 낮고, 엽신/엽초비는 시비량의 증가에 따라 낮아지며, 엽초/간비는 높아지고 엽신/간십엽초중비율은 낮아졌다. 6. 시비량의 증가에 따라 공시품종 모두 신장절위의 엽면적, 엽신중, 엽초중은 증대되었다. 그에 따라 수량도 증가하는 경향을 보이고, 간중은 시비량 증가에 따라 감소되고 수량은 반대로 증대되는 경향을 보이는데 그 정도는 품종에 따라 차이가 있다. 7. 출수기 및 성숙기에 있어서의 잎의 실소함량은 시비량에 따라 다르며, 공시품종 평균실소함량은 출수기에 있어서 N8kg 시비구 2.74%, N12kg 시비구 2.49는 각구 0.80%, 0.92% 및 1.03%로서 증비에 의하여 실소함량이 현저히 증가되고 있으며, 엽위별에 있어서는 상위엽일수록 높았다. 8. 잎의 실소 함량은 품종간에 차이가 있는데, 동일품종내에서는 출수기와 성숙기에 있어서 그 함량이 높을수록 수량이 증대되였다.

• 한국유통학회지:유통연구
• /
• 제15권1호
• /
• pp.1-24
• /
• 2010

국내 대형마트 점포 수는 2008년 기준 403개로 포화시점에 근접하고 있다. 이러한 경쟁상황에서 '점포충성도(store loyalty)'가 지속적 경쟁우위를 위한 전략적 도구로써 그 활용성이 점점 더 중요시 되고 있다. 다양한 관점에서 점포충성도를 대형마트 연구의 핵심적 과제 다루어왔으나, 통합적인 연구 접근 방법이 미흡한 실정이다. 따라서 본 연구에서는 통합적 관점에서 점포충성도가 형성되는 두 가지 경로를 제안하였다. 이중경로모형은 첫째, 내재적 경로 '서비스품질$\rightarrow$고객만족$\rightarrow$점포충성도', 둘째, 외재적 경로 '점포개성$\rightarrow$점포동일시$\rightarrow$점포 충성도'로 구성된다. 조사대상은 대형마트를 이용하는 소비자들을 대상으로 진행하였으며, 구조방정식모형 분석을 통하여 제안된 이중경로모형의 적합성 및 가설검증을 실시하였다. 연구결과, 모형의 적합지수들은 상당히 좋은 값들을 보여주고 있다. 또한 본 연구에서 새롭게 제시된 내재적 경로인 서비스품질은 고객만족에 정의 영향을 미치고, 고객만족은 결과변수인 대형마트의 점포충성도에 매우 유의하게 영향을 준 것으로 나타났다. 그리고 외재적 경로에서 대형마트의 점포개성은 점포동일시에 긍정적인 영향을 주고 매개변수인 점포개성은 점포충성도에 영향을 미치는 것으로 나타났다. 이를 통해 본 연구는 대형마트의 점포충성도 형성에 관한 두 가지 경로를 제시함으로써, 이론적, 관리적 시사점을 도출하였고 연구의 한계점과 미래연구방향을 제시하였다.