• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.6 no.1
• /
• pp.65-72
• /
• 2008

The purpose of the HLW deep geological disposal is to isolate and to delay the radioactive material release to human beings and the environment for a long time so that the toxicity does not affect to the environment. The main requirements for the HLW repository design is to keep the buffer temperature below $100\;^{\circ}C$ in order to maintain its integrity. So the cooling time of spent fuels discharged from the nuclear power plant is the key consideration factors for efficiency and economic feasibility of the repository. The disposal tunnel/disposal hole spacing, the disposal area and thermal capacity required for the deep geological repository layout which satisfies the temperature requirement of the disposal system is analyzed to set the optimized spent fuels cooling time. To do this, based on the reference disposal concept, thermal stability analyses of the disposal system have been performed and the derived results have been compared by setting the spent fuels cooling time and the disposal tunnel/disposal hole spacing in various ways. From these results, desirable spent fuels cooling time in view of disposal area is derived. The results shows that the time reaching the maximum temperature within the design limit of the temperature in the disposal site is likely shortened as the cooling time of spent fuels becomes short. Also it seems that the temperature-rising and-dropping patterns in the disposal site are of smoothly varying form as the cooling time of spent fuels becomes long. In addition, it is revealed that a desirable cooling time of spent fuels is approximately 40-50 years when spent fuels are supposedly disposed in the deep geological disposal site with its structural scale under consideration in this study.

• The Journal of Korean Society for Radiation Therapy
• /
• v.25 no.1
• /
• pp.33-40
• /
• 2013

Purpose: The purpose of this study was to evaluate the possibility to optimize the gated treatment delivery time and maintenance of stable respiratory by the introduction of breath with the assistance of auditory-visual-tactile sense. Materials and Methods: The experimenter's respiration were measured by ANZAI 4D system. We obtained natural breathing signal, monitor-induced breathing signal, monitor & ventilator-induced breathing signal, and breath-hold signal using real time monitor during 10 minutes beam-on-time. In order to check the stability of respiratory signals distributed in each group were compared with means, standard deviation, variation value, beam_time of the respiratory signal. Results: The stability of each respiratory was measured in consideration of deviation change studied in each respiratory time lapse. As a result of an analysis of respiratory signal, all experimenters has showed that breathing signal used both Real time monitor and Ventilator was the most stable and shortest time. Conclusion: In this study, it was evaluated that respiratory gated radiation therapy with auditory-visual-tactual sense and without auditory-visual-tactual sense feedback. The study showed that respiratory gated radiation therapy delivery time could significantly be improved by the application of video feedback when this is combined with audio-tactual sense assistance. This delivery technique did prove its feasibility to limit the tumor motion during treatment delivery for all patients to a defined value while maintaining the accuracy and proved the applicability of the technique in a conventional clinical schedule.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.43 no.1
• /
• pp.61-68
• /
• 2017

The key quality attributes of the pressed powder, one of base makeup products, are skin-affinity and spreadability. In general, there was a limit to meet skin-affinity and spreadability simultaneously, which are opposite attributes each other. In this study, air jet mill process was tried to satisfy two main properties. Skin-affinity was improved by a wet coating of sericite with a mixture of lauroyl lysine (LL) and sodium cocoyl glutamate (SCG). The application of mono-dispersed polymethyl methacrylate (PMMA) and diphenyl dimethicone/vinyl diphenyl dimethicone/silsesquioxane crosspolymer (DDVDDSC) improved both qualities. Air jet mill process has been mainly applied in the pharmaceutical and food industries, and is a method used for processing powder materials in cosmetic field. In this study, we were able to complete makeup cosmetics with an optimum particle size $6.8{\mu}m$ by combining the air jet mill process at the manufacturing stage. It was confirmed that the Ti element was uniformly distributed throughout the cosmetics by EDS mapping, and that the corners of the tabular grains were rounded by SEM analysis. It is considered that this can provide an effect of improving the spreadability when the cosmetic is applied to the skin by using a makeup tool. LL with excellent skin compatibility and SCG derived from coconut with little skin irritation were wet coated to further enhance the adhesion of sericite. SEM images were analyzed to evaluate effect of the dispersion and uniformity of PMMA on spreadability. With the spherical shapes of similar size, it was found that the spreading effect was further increased when the distribution was homogeneously mono-dispersed. The dispersion and spreadability of PMMA were confirmed by measuring the kinetic friction and optimal content was determined. The silicone rubber powder, DDVDDSC, was confirmed by evaluating the hardness, spreading value, and drop test. Finally, it was found that the dispersion of PMMA and silicone rubber powder affected spreadability. Such makeup cosmetics have excellent stability in drop test while having appropriate hardness, and good stability over time. Taken together, it is concluded that air jet mill process can be utilized as a method to improve skin-affinity and spreadability of the pressed powder.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.13 no.2
• /
• pp.215-221
• /
• 1984

To investigate stability for the quality of selected ginseng products, their sorption properties were clarified in red ginseng extract(RGEP), and red ginseng extract powder(RGEP), and red ginseng extract tea(RGET). Simultaneously, the BET monolayer value of each product was determined in order to inquire out the possibility of establishment as a criterion for the optimum moisture content of the ginseng products. Based on the BET monolayer moisture level of spray dried RGEP which ranged from 4.08 to 4.65%, it would be desirable to establish the optimum moisture content of the products at 4.4${\pm}$0.3%. This is 1.3 to 1.9% lower than the criter on, "less than 6.0%". The optimum moisture level for RGET of which monolayer value ranged 0.93 to 1.37% would be 1.2${\pm}$0.17%. In this case, the maximum permissible limit of moisture content could presumably be raised up to 1.37% in place of current criterion, "less than l.2%". From the results of a study on the growth of molds, the optimum moisture content for RGE assumed to be extended up to 40.0${\pm}$1.07 despite 36.0${\pm}$1.0% of the present criterion. On the other hand, a storage study under the maltreated condition, $48{\pm}2^{\circ}C$ 75%RH, was also carried out in order to make it clear whether the BET monolayer values were able to be used as indices for optimum moisture level of the products. In all samples tested adsorption occurred at even higher levels of moisture than the monolayer values. However, since there are many other possible factors affecting the quality of products the optimum moisture content is preferable to be reduced to the monolayer value. As a result, it was proved that the optimum level of moisture for both RGEP and RGET could be established by the monolayer values.

• Journal of Korea Water Resources Association
• /
• v.51 no.9
• /
• pp.827-837
• /
• 2018

The stabilities of sliding and overturning of caisson and bearing capacity of mound against eccentric and inclined loads, which possibly happen to a composite caisson breakwaters, have been analyzed by using the technique of multiple failure modes. In deterministic approach, mathematical functions have been first derived from the ultimate limit state equations. Using those functions, the minimum cross section of caisson can straightforwardly be evaluated. By taking a look into some various deterministic analyses, it has been found that the conflict between failure modes can be occurred, such that the stability of bearing capacity of mound decreased as the stability of sliding increased. Therefore, the multiple failure modes for the composite caisson breakwaters should be taken into account simultaneously even in the process of deterministically evaluating the design cross section of caisson. Meanwhile, the reliability analyses on multiple failure modes have been implemented to the cross section determined by the sliding failure mode. It has been shown that the system failure probabilities of the composite breakwater are very behaved differently according to the variation of incident waves. The failure probabilities of system tend also to increase as the crest freeboards of caisson are heightening. The similar behaviors are taken place in cases that the water depths above mound are deepening. Finally, the results of the first-order modal are quite coincided with those of the second-order modal in all conditions of numerical tests performed in this paper. However, the second-order modal have had higher accuracy than the first-order modal. This is mainly due to that some correlations between failure modes can be properly incorporated in the second-order modal. Nevertheless, the first-order modal can also be easily used only when one of failure probabilities among multiple failure modes is extremely larger than others.

• Journal of Chitin and Chitosan
• /
• v.23 no.4
• /
• pp.244-255
• /
• 2018

Natural extract in liquid phase was adjusted to 0, 0.25, 0.5, 1, 2, and 4% concentration to check microbial changes and to measure 4, 8, $12^{\circ}C$ for refrigeration temperature. In the case of grapefruit extract, the microbial safety was maintained at all the concentrations at $4^{\circ}C$ storage, but the antimicrobial activity was maintained at $12^{\circ}C$ storage and at $8^{\circ}C$ and 21 days storage. In the case of grape seed extract, only the 4% of the culture at $8^{\circ}C$ satisfied the requirement of safety of food distribution for the last 21 days, and the safety criterion was satisfied only at 4% concentration at $12^{\circ}C$ for 18 days. Complex Scutellaria baicalensis extract showed the total number of microbial cells treated by concentration. It was confirmed that microbial flow safety was maintained at low temperature ($4^{\circ}C$). However, at $8^{\circ}C$ and $12^{\circ}C$, Exceeded the distribution limit. When polylysine was applied to brown rice cake, it showed activity in all groups except $4^{\circ}C$, but these properties were not observed at $8^{\circ}C$ and $12^{\circ}C$. At a concentration of 0.5% or more of chitosan, the growth of the microorganism is suppressed by the 21st day very stably, and a similar tendency is observed at 8 and $12^{\circ}C$, so that it may be an antimicrobial material that inhibits microorganisms. At the first day, the distribution standards for general bacterial counts were exceeded.Ethyl-pyruvate showed that microorganism safety was maintained at $4^{\circ}C$ and 1% concentration, and food safety was stable even at 2 or 4%. Glycine showed very good and stable distribution stability at $4^{\circ}C$. However, at $8^{\circ}C$ and $12^{\circ}C$, the shelf life of 14 days could not be maintained as with the addition of other antimicrobial active substances.

• The Journal of Engineering Geology
• /
• v.29 no.2
• /
• pp.85-97
• /
• 2019

It can be observed that steep slopes ($65^{\circ}$ to $80^{\circ}$) consist of rock masses were kept stable for a long time. In rock-mass slopes with similar ground condition, steeper slopes than 1 : 0.5 ($63^{\circ}$) may be applied if the discontinuities of rock-mass slope are distributed in a direction favorable to the stability of the slope. In making a decision the angle of the slope, if the preliminary rock mass conditions applicable to steep slope are quantitatively setup, they may be used as guidance in design practice. In this study, the above rock mass was defined as a good continuum rock mass and the quantitative setup criterion range was proposed using RMR, SMR and GSI classifications for the purpose of providing engineering standard for good continuum rock mass conditions. The methods of study are as follows. The stable slope at steep slopes ($65^{\circ}$ to $80^{\circ}$) for each rock type was selected as the study area, and RMR, SMR and GSI were classified to reflect the face mapping results. The results were reviewed by applying the calculated shear strength to the stable analysis of the current state of rock mass slope using the Hoek-Brown failure criterion. It is intended to verify the validity of the preliminary criterion as a rock mass condition that remains stable on a steep slope. Based on the analysis and review by the above research method, it was analyzed that a good continuum rock mass slope can be set to Basic RMR ${\geq}50$ (45 in sedimentary rock), GSI and SMR ${\geq}45$. The safety factor of the LEM is between Fs = 14.08 and 67.50 (average 32.9), and the displacement of the FEM is 0.13 to 0.64 mm (average 0.27 mm). This can be seen as a result of quantitative representation and verification of the stability of a good continuum rock mass slope that has been maintained stable for a long period of time with steep slopes ($65^{\circ}$ to $80^{\circ}$). The setup guideline for a good continuum rock mass slope will be able to establish a more detailed setup standard when the data are accumulated, and it is also a further study project. If stable even on steep slopes of 1 : 0.1 to 0.3, the upper limit of steep slopes is 1 : 0.3 with reference to the overseas design standards and report, thus giving the benefit of ensuring economic and eco-friendlyness. Also, the development of excavation technology and plantation technology and various eco-friendly slope design techniques will help overcome psychological anxiety and rapid weathering and relaxation due to steep slope construction.

• Food Engineering Progress
• /
• v.21 no.3
• /
• pp.225-232
• /
• 2017

Most of the red ginseng (RG) products contain active substances derived from hot water or alcohol extraction. Since active substances of RG are divided into two types - water-soluble and liposoluble - water or alcohol is needed as an extraction solvent and this leads the different extraction yields and components of the active substances. To overcome the limit, whole red ginseng powder can be used and consumed by consumers. In this study, the physicochemical properties and extractable active substance contents of variable-sized RG powder ($158.00{\mu}m$, $8.45{\mu}m$, and $6.33{\mu}m$) were analyzed, and dispersion stability was measured to investigate the suitable size of RG powder for industrial processing. In the results, no significant difference was found from the changes in color intensity and thiobarbutric acid tests at $4^{\circ}C$, $25^{\circ}C$, and $40^{\circ}C$ for 4 weeks. There was no significant difference on the production of antioxidants and ginsenoside among the samples (p>0.05). In dispersion stability, $RG-158.00{\mu}m$ was precipitated immediately, and the dispersion stabilities between $RG-8.45{\mu}m$ and $RG-6.33{\mu}m$ showed no significant difference. It implies that fine RG is suitable for the production process. With further study, it seemed that the physicochemical effects of RG particle sizes can be clearly revealed.

• Journal of Food Hygiene and Safety
• /
• v.37 no.2
• /
• pp.97-106
• /
• 2022

Listeria monocytogenes (L. monocytogenes) is one of gram-positive foodborne pathogens with a very high fatality rate. Unlike most foodborne pathogens, L. monocytogenes is capable of growing at low temperatures, such as in refrigerated foods. Thus, various physical and chemical prevention methods are used in the manufacturing, processing and distribution of food. However, there are limitations to the methods such as possible changes to the food quality and the consumer awareness of synthetic preservatives. Thus, the aim of this study was to evaluate the anti-listeria activity of lactic acid bacteria (LAB) isolated from kimchi and characterize the bacteriocin produced by Lactococcuslactis which is one of isolated strains from kimchi. The analysis on the anti-listeria activity of a total of 36 species (Lactobacillus, Weissella, Lactobacillus, and Lactococcus) isolated from kimchi by the agar overlay method revealed that L. lactis NJ 1-10 and NJ 1-16 had the highest anti-listeria activity. For quantitatively analysis on the anti-listeria activity, NJ 1-10 and NJ 1-16 were co-cultured with L. monocytogenes in Brain Heat Infusion (BHI) broth, respectively. As a result, L. monocytogenes was reduced by 3.0 log CFU/mL in 20 h, lowering the number of bacteria to below the detection limit. Both LAB strains showed anti-listeria activity against 24 serotypes of L. monocytogenes, although the sizes of clear zone was slightly different. No clear zone was observed when the supernatants of both LAB cultures were treated with proteinase-K, indicating that their anti-listerial activities might be due to the production of bacteriocins. Heat stability of the partially purified bacteriocins of NJ 1-10 and NJ 1-16 was relatively stable at 60℃ and 80℃. Yet, their anti-listeria activities were completely lost by 60 min of treatment at 100℃ and 15 min of treatment at 121℃. The analysis on the pH stability showed that their anti-listeria activities were the most stable at pH 4.01, and decreased with the increasing pH value, yet, was not completely lost. Partially purified bacteriocins showed relatively stable anti-listeria activities in acetone, ethanol, and methanol, but their activities were reduced after chloroform treatment, yet was not completely lost. Conclusively, this study revealed that the bacteriocins produced by NJ 1-10 and NJ 1-16 effectively reduced L. monocytogenes, and that they were relatively stable against heat, pH, and organic solvents, therefore implying their potential as a natural antibacterial substance for controlling L. monocytogenes in food.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.1 no.1
• /
• pp.53-68
• /
• 1981

Most clays under sustained load exhibit time-dependent deformation because of creep movement of soil particles and many investigators have attempted to relate their findings to the creep behavior of natural ground and to the long-term stability of slopes. Since the creep behavior of clays may assume a variety of forms depending on such factors as soil plasticity, activity and water content, it is difficult and complicated to analyse the creep behavior of clays. Rheological models composed of linear springs in combination with linear or nonlinear dashpots and sliders, are generally used for the mathematical description of the time-dependent behavior of soils. Most rheological models, however, have been proposed to simulate the behavior of secondary compression for saturated clays and few definitive data exist that can evaluate the behavior of non-saturated clays under the action of sustained stress. The clays change gradually from a solid state through plastic state to a liquid state with increasing water content, therefore, the rheological models also change. On the other hand, creep is time-dependent, and also the effect of thixotropy is time-function. Consequently, there may be certain correlations between creep behavior and the effects of thixotropy in compacted clays. In addition, the states of clay depend on water content and hence the height of the specimen under drained conditions. Futhermore, based on present and past studies, because immediate elastic deformation occurs instantly after the pressure increment without time-delayed behavior, the factor representing immediate elastic deformations in the rheological model is necessary. The investigation described in this paper, based on rheological model, is designed to identify the immediate elastic deformations and the effects of thixotropy and height of clay specimens with varing water content and stress level on creep deformations. For these purposes, the uniaxial drain-type creep tests were performed. Test results and data for three compacted clays have shown that a linear top spring is needed to account for immediate elastic deformations in the rheological model, and at lower water content below the visco-plastic limit, the effects of thixotropy and height of clay specimens can be represented by the proposed rheological model not considering the effects. Therefore, the rheological model does not necessitate the other factors representing these effects. On the other hand, at water content higher than the visco-plastic limit, although the state behavior of clays is visco-plastic or viscous flow at the beginning of the test, the state behavior, in the case of the lower height sample, does not represent the same behavior during the process of the test, because of rapid drainage. In these cases, the rheological model does not coincide with the model in the case of the higher specimens.