• 소성∙가공
• /
• 제5권2호
• /
• pp.156-164
• /
• 1996

To investigate the behavior of plastic deformation in axisymmetric extrusion through square dies, experimental works with the plasticine as a model material are carried out at the room temperature. Some mechanical properties of the model material are determined by compression and ring compression tests. Visioplasticity method using expermental grid distortion in extrusion is introduced to analyze the plastic flow strain rate and strain distribution. In spite of severe deformation during the extrusion through square die the visioplasticity method shows good results for the distribution of effective strain rate and effective strain.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.109-110
• /
• 2010

• 소성∙가공
• /
• 제17권7호
• /
• pp.511-516
• /
• 2008

A drawbead die for the experimental determination of drawbead forces was newly introduced in this paper. While the conventional Nine's drawbead die inevitably includes effects of a blank holding force on the measured drawbead forces, the new drawbead die excludes it by removing the blank holder contact in the dieface. Therefore, the new drawbead die can provide more realistic drawbead forces without considering somewhat arbitrary effect of blank holder with the computational procedure of forming process. The drawbead opening force and restraining force obtained by adopting the two experimental dies were compared for the validation of accuracy in the FEM simulation of automotive fender forming process. The compared section strains and draw-ins confirmed that the present drawbead die provides better drawbead forces for an accurate FEM simulation of sheet metal forming process.

• Design & Manufacturing
• /
• 제2권3호
• /
• pp.40-44
• /
• 2008

Shaving in sheet metal forming is defined as a finish process to make the sheared surface clean which was blanked or pierced in the previous shearing stage. In this study the new shaving technique is applied to the progressive operation. The specimen is automatically fed by continuous movement of the strip. Which improve the positioning accuracy higher. For this study a square part which consist of blanking and piercing is selected for investigation and the progressive die which includes pre-piercing, pierce-shaving, half-blanking and blank-shaving etc is prepared for specimens of steel sheet(SPCC) and aluminum alloy sheet(AL5052). Experiments are carried out for several working variables such as shaving allowance, pre-shearing clearance and relative half-blanking depth. Consequently it was confirmed that the shaving by progressive die can be successfully employed to produce the clean parts requiring shaving process and optimum working conditions for shaving SPCC and AL5052 sheet metal are shaving allowance of 0.2mm(1.3% of thickness) and pre-shearing clearance of 5%.

• 소성∙가공
• /
• 제3권2호
• /
• pp.156-166
• /
• 1994

An arbitrary Lagrangian-Eulerian (ALE) finite element method has been developed. The finite element formation is derived and implemented for rigid-viscoplastic materials. The developed computer program is applied to the analysis of axisymmetric square die extrusion, which has many difficulties with updated Lagrangian approach. The results are compared with those from updated Largrangian approach. The results are compared with those from updated Lagrangian finite element program. Updating scheme of time dependent variables and mesh control are also examined.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.119-128
• /
• 1998

In this paper, nonsteady state shaped drawing process has been investigated using the three-dimensional rigid-plastic finite element method. In order to analyze the shaped drawing process, a method to define straight converging die considering straight die part, die radius part and bearing part has been proposed. In addition, the modeling of initial billet and the generation procedure of mesh system have been suggested. The three-dimensional rigid-plastic finite element simulation has been performed for a square sectional drawing process and its result has been confirmed in comparison with the existing experimental one. Also, for the same process conditions, the effect of perimeter ratio in the shaped drawing process has been investigated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.797-801
• /
• 2003

The mechanical properties such as shear strength and the hardness of milli-size products that manufactured for various process parameters by forward extrusion using square dies are investigated. Shear strength test is implemented for the observation of relation between vickers hardness and shear strength in the interface of head and shaft part of a stepped pin. When the extrusion ratios of pure aluminum and pure copper billets increase, the hardness on both the surface and the center line of a pin also increase, especially the hardness on the surface is shown to be a little higher than on the center. The existence of knock-out pad in extrusion die caused hardness increase in the interface of a extruded pin. As compared shear strength with hardness of a pin, the approximated linear relations are suggested in this study.

• 대한기계학회논문집
• /
• 제19권8호
• /
• pp.1844-1853
• /
• 1995

Theoretical and experimental drawing characteristics for the single circular and square drawbeads are discussed. During the blank holding process, the strain distributions of upper and lower skins of specimens, and the die reactional forces are analysed by F. E. M., and they are compared with the experimental results. The drawbead restraining forces and strain distributions for the drawn specimens by the various drawing length are also analysed and compared with the experimental results. It is concluded that the theoretical simulations and results could be very useful for the prediction of real cases.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 추계학술대회논문집
• /
• pp.14-19
• /
• 1996

This study presents development of finite element simulation program and analysis of hot extrusion through square dies with mandrel. The design of extrusion dies is still an art rather than science. Die design for a new extrusion is developed from through in-plant trials. In the present paper, three-dimensional steady-state finite element simulation program is developed. The developed system is effectively used to simulate extrusion of clamp shaped hollow section. The objective of the present paper is to study the possibility of integrating this method into the design of dies for extrusion of complex section. To obtain sound product, the distributions and effects of temperature, effective strain rate, mean strain rate and mean stress are studied.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.86-89
• /
• 2002

Due to extremely large reduction of area or extrusion ratio in ordinary production of extruded profiles, anisotropy is naturally induced by large severe deformation during the extrusion process. Therefore, the anisotropic properties play a great role in the post processing of extruded profiles, such as in bending. Moreover, undesirable deformation will be involved when the deformation-induced anisotropy is ignored. In order to observe the deformation-induced anisotropy of the thin-walled product, the proposed algorithm is applied to some chosen industrial extrusion processes. In the resent work, the method for prediction of deformation-induced anisotropy employing the Barlats six-component yield potential to the rigid-plastic finite element method is proposed. The proposed algorithm is verified with the comparison to the crystallographic texture analysis, and then applied to the C-section exclusion process using a square die. The predicted anisotropy is then compared with the experimental and computational observations for validating the proposed algorithm.