• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.389-391
• /
• 2011

This paper has been studied about design of linear 25Watt Power amplifier for VDR(VHF Data Radio). VDR's frequency band is 117.975~137MHz, and CSMA(Carrier Sense Multiple Access), D8PSK(Differential Eight Phase Shift Keyed), 25KHz's channel bandwidth use. It also stated in DO-281A MOPS output power, symbol constellation error, spurious emissions, adjacent channel power must be met. HPA is designed to meet DO-281A standard.

• Structural Engineering and Mechanics
• /
• v.10 no.2
• /
• pp.157-164
• /
• 2000

This paper discusses the error propagation characteristics of the Newmark explicit method, modified Newmark explicit method and ${\alpha}$-function dissipative explicit method in pseudodynamic tests. The Newmark explicit method is non-dissipative while the ${\alpha}$-function dissipative explicit method and the modified Newmark explicit method are dissipative and can eliminate the spurious participation of high frequency responses. In addition, error propagation analysis shows that the modified Newmark explicit method and the ${\alpha}$-function dissipative explicit method possess much better error propagation properties when compared to the Newmark explicit method. The major disadvantages of the modified Newmark explicit method are the positive lower stability limit and undesired numerical dissipation. Thus, the ${\alpha}$-function dissipative explicit method might be the most appropriate explicit pseudodynamic algorithm.

• Journal of electromagnetic engineering and science
• /
• v.4 no.4
• /
• pp.143-149
• /
• 2004

This paper describes characteristics of the single-balanced low IF resistive FET mixer for the digital beam forming(DBF) receiver. This DBF receiver based on the direct conversion method is designed with Low IF I and Q channel. A radio frequency(RF), a local oscillator(LO) and an intermediate frequency(IF) considered in this research are 1950 MHz, 1940 MHz and 10 MHz, respectively. Super low noise HJ FET of NE3210S01 is considered in design. The measured results of the proposed mixer are observed IF output power of -22.8 dBm without spurious signal at 10 MHz, conversion loss of -12.8 dB, isolation characteristics of -20 dB below, 1 dB gain compression point(PldB) of -3.9 dBm, input third order intercept point(IIP3) of 20 dBm, output third order intercept point(OIP3) of 4 dBm and dynamic range of 30 dBm. The proposed mixer has 1.0 dB higher IIP3 than previously published single-balanced resistive and GaAs FET mixers, and has 3.0 dB higher IIP3 and 4.3 dB higher PldB than CMOS mixers. This mixer was fabricated on 0.7874 mm thick microstrip $substrate(\varepsilon_r=2.5)$ and the total size is $123.1\;mm\times107.6\;mm$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.4
• /
• pp.805-817
• /
• 1999

In this paper, the needs for introduction and adoption of MㆍHF DSC/NBDP system and for developments of its circuits and call sequences for use in the maritime mobile services for small-ships, leisure-ships and fishing ships are analyzed, discussed. Also design and implement for MㆍHF(1.6-4MHz) DSC/NBDP system is discussed. Most of casualties have been arisen from small-ships and fishing ships during last 5 years. So, the SAR schematic plans should been prepared to prevent casualties and facilitate the activities of SAR for those ships. DSC/NBDP for MㆍHF system is able to fulfill the roles of efficient SAR communication functions, and to advance the SAR system to small ships and fishing ships. This study is focused on the techniques of processing the DSC call sequences and the ARQ sequences of NBDP system. Especially ARQ sequences are expanded into processing of Korean letters, designed the call sequences and code conversion algorithm for Korean-code. It will be evaluated the availability of Korean-NBDP system. In designing the Transmitting circuits and Receiving circuits, for the carrier generation, DDS(Direct Digital Synthesizer) is used in stead of the Phase Locked Loop and frequency conversion by the mixer, BPF. And PSK modulation signals are directly generated by the controls of DDS, which show the characteristics of Spurious Free Dynamic Range are below -62dBc. Also, the monolithic U subsystem IC which provides various functional components, AD608 is used for designing the receiving circuitsㆍAnd the algorithm of Phasing methode for FSK demodulation are devised to process IF frequency 455kHz in the IF circuits.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.1 no.1
• /
• pp.23-31
• /
• 1976

When Television signal of VHF and UHF channel is retransmitted at the relay system with 6MHz Bandwidth including video and aural signals, the image is often affected with the unnatural changes of output amplitude frequency response within ttle region of dual sideband near to the carrier frequency. These phenomena are caused by the unnecessary lower sideband due to the spurious emission at the local oscillator, the nonlinear distortion in the linear amplifier, the intermoudulation distortion with the components of neighboring signal, the AM-PM conversion, and the envelope delay distortion. From the output characteristics, considering above results, the chief cause is caused by nonlinear response and has an effect on the bias states. Finally, it is confirmed that the effects on neighboring signal appear high in case of Down conversion than Up conversion and obtained the method for reducing the effects on the system.

• Smart Structures and Systems
• /
• v.6 no.2
• /
• pp.115-133
• /
• 2010

A modal filter is a tool used to extract the modal coordinates of each individual mode from a system's output. This is achieved by mapping the response vector from the physical space to the modal space. It decomposes the system's responses into modal coordinates, and thus, on the output of the filter, the frequency response with only one peak corresponding to the natural frequency to which the filter was tuned can be obtained. As was shown in the paper (Deraemecker and Preumont 2006), structural modification (e.g. a drop in stiffness or mass due to damage) causes the appearance of spurious peaks on the output of the modal filter. A modal filter is, therefore, a great indicator of damage detection, with such advantages as low computational effort due to data reduction, ease of automation and lack of sensitivity to environmental changes. This paper presents the application of modal filters for the detection of stiffness changes. Two experiments were conducted: the first one using the simulation data obtained from the numerical 7DOF model, and the second one on the experimental data from a laboratory stand in 4 states of damage.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.254-262
• /
• 2009

This paper presents a novel simple filter design method based on a parallel short-ended coupled-line structure with capacitive loading for size reduction and ultra-broad rejection of spurious passbands. In addition, the introduction of a cross-coupling capacitor into the miniaturized coupled-line can create a transmission zero at the second harmonic frequency for better frequency selectivity and attenuation level. The aperture compensation technique is also applied to achieve a strong coupling in the coupled-line section. The influence of using the connecting transmission line to cascade two identical one-stage filters is studied for the first time. Specifically, such a two-stage bandpass filter operating at 2.3 GHz with a fractional bandwidth of 10% was designed and realized with low-temperature co-fired ceramic technology for application in base stations that need high power handling capability. It achieved attenuation in excess of -40 dB up to $4f_0$ and low insertion loss of -1.2 dB with the size of 10 mm ${\times}$ 7 mm ${\times}$ 2.2 mm. The measured and simulated results showed good agreement.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.1
• /
• pp.66-74
• /
• 2012

The virtual target signal generator was developed to verify the shipborne tracking radar performance. It was used to DRFM(Digital RF Memory) method to generate the virtual moving targets. The target signal includes Doppler shift and RCS according to the target motion. And the signal generator can make jamming signal and clutter to test shipborne radar performance at real environmental condition. This paper described the functional diagram and the hardware configuration items to meet the test requirements for the tracking radar. And it showed the critical design points for the sub-systems. The signal generator which was developed in this paper shared the operational information of the radar with the radar command and control part. To test the frequency agility of the radar, it had the local oscillator which could do high speed frequency switching according to radar information. By communicating between the signal generator and the radar command and control part, the local oscillator of signal generator could be controlled every pulse. It reduced the instantaneous bandwidth of signal generator and minimized the spurious. So it lowered the probability of generating wrong targets.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.226-229
• /
• 2005

In this study, a step-down piezoelectric transformer was fabricated to utilize as an adapter for charging batteries of mobile electronic appliances. The ceramic part of the transformer is $Pb[(Mn_{1/3}Sb_{2/3})_{0.05}Zr_{0.475}Ti_{0.475}]O_3$ with mechanical quality factor of 1600, electromechanical coupling coefficient 59 %, and piezoelectric constant d33 1300, which can be utilized as a piezoelectric transformer. A simply fabricated disk-typed test pattern of diameter 28 mm and thickness 2 mm was used to characterize resonant frequency, Qm, kp according to the different input/output electrode area. efficiency and power as a function of load resistance was also investigated. The sample APT showed some spurious mode and BPT showed better frequency property. Taking all properties which are admittance, effective electromechanical coupling coefficient and mechanical quality factor most suitable for piezoelectric transformer is BPT which has 12 mm diameter electrode and the condition of 15 Vrms, 30 $\Omega$ made the maximum efficiency of 93.7 % and maximum power is 6W with 50 Vrms.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.653-662
• /
• 1999

In this paper, subharmonically injection locked oscillator(SILO) was designed and measured. SILO with series feedback was designed using Two Signal Method(TSM). The free-running oscillator frequency was 9.4 GHz with 6 dBm output power. In case of injection, the multiplied injected signal locked the free-running frequency. The locked signal output power was higher than any other spurious response at least 40 dB. The locking range was 220MHz (second subharmonic locking), 100 MHz(4th subharmonic locking), and phase noise was -111 dBc/Hz, -104 dBc/Hz at 100kHz offset, respectively.