• Journal of ILASS-Korea
• /
• v.8 no.3
• /
• pp.19-26
• /
• 2003

In this study, experimental study on atomization characteristics of the fuel spray impinging on the wall was at different wall distances and angles of wall inclination. The fuel injection system was composed based on the common rail system. and the injection signal was synchronized by the delay generator. The atomization characteristics of the injected spray were analyzed in terms of the SMD and velocities which were measured by using the phase Doppler particle analyzer system. It is revealed that the free spray is atomized actively above 50mm form the injector tip. In the cases of the impinged spray, the 5MD and velocity of the impinged spray are smaller than those of the free spray. The impinged spray has the maximum near the 35mm of the radial distance from the injector axis, and the atomization performance is enhanced with the decrease of the wall distance.

• Journal of ILASS-Korea
• /
• v.6 no.2
• /
• pp.16-21
• /
• 2001

This paper describes the macroscopic behavior and atomization characteristics of the high-pressure gasoline swirl injector in direct-injection gasoline engine. The global spray behavior of fuel injector was visualized by shadowgraph technique. The atomization characteristics of gasoline spray such as mean diameter and mean velocity of droplets were measured by the phase Doppler particle analyzer system. The macroscopic visualization and experiment of particle measurement on the fuel spray were investigated at 7 and 10 MPa of injection pressure under different spray cone angle. The results of this work show that the geometry of injector was more dominant over the macroscopic characteristics of spray than the fuel injection pressure and injection duration. As for the atomization characteristics, the increase of injection pressure resulted in the decrease of fuel droplet diameter and the atomization characteristics differed as to the spray cone angle. The most droplets had under $25{\mu}m$ diameter and for the large droplets(upper $40{\mu}m$) as the spray grew the atomization presses were very slow. Comparison results between the measured droplet distribution and the droplet distribution functions revealed that the measured droplet distribution is very closed to the Normal distribution function and Nukiyama-Tanasawa's function.

• Journal of ILASS-Korea
• /
• v.24 no.1
• /
• pp.1-7
• /
• 2019

This study was carried out to analyze the spray characteristics as a function of the operating parameters of urea injector used in Urea-SCR system of passenger diesel vehicle. Spray visualization and PDPA experiment were performed to analyze the macroscopic spray development and atomization performance of urea-water-solution. For the urea injector, the deformation of the spray head does not appear to be significant because it operates at a low pressure conditions, and the liquid core and primary droplet are observed throughout the operating conditions. No increase in atomization is seen when the operating pressure is increased, and the spray develops linearly due to poor atomization characteristics. The macroscopic spray behavior of the low-pressure urea injector is predictable through the modification of the Hiroyasu equation.

• Journal of ILASS-Korea
• /
• v.8 no.4
• /
• pp.1-8
• /
• 2003

The objective of this study is to investigate experimentally atomization characteristics for differently made an ultrasonic twin-fluid nozzle. A spray system, an ultrasonic system, and three different type(Nozzle type, Tube type, Conventional type)are made and tested by applied with ultrasonic energy. In this investigation, the measurement and calculation of spray droplet are to analyze the effects of ultrasonic energy on the agricultural atomization system. Through the measurement of suray angle, spray column using, high speed camera and PDA, it is found that nozzle type is highest efficiency than that of tube type and conventional type. It was found that the ultrasonic energy increased the atomization efficiency of spray droplets about 9% respectively and spray angle was wide spray.

• Journal of Mechanical Science and Technology
• /
• v.18 no.7
• /
• pp.1177-1186
• /
• 2004

In this paper, the spray atomization characteristics of a gasoline direct-injection injector were investigated experimentally and numerically. To visualize the developing spray process, a laser sheet method with a Nd :YAG laser was utilized. The microscopic atomization characteristics such as the droplet size and velocity distribution were also obtained by using a phase Doppler particle analyzer system at the 5 ㎫ of injection pressure. With the experiments, the calculations of spray atomization were conducted by using the KIVA code with the LISA-DDB breakup model. Based on the agreement with the experimental results, the prediction accuracy of LISA-DDB breakup model was investigated in terms of the spray shapes, spray tip penetration, SMD distribution, and axial mean velocity. The results of this study provides the macroscopic and microscopic characteristics of the spray atomization, and prediction accuracy of the LISA-DDB model.

• Journal of ILASS-Korea
• /
• v.10 no.1
• /
• pp.1-9
• /
• 2005

When the water jets heated up to the saturation temperature at a high line pressure are sprayed into a reduced (atmospheric) pressure through an air-assisted nozzle, the jets experience sudden exposure into a reduced pressure, get superheated and produce steam bubbles while atomization processes of jets are taking place. This process is called flash atomization. In this study the flash atomization of superheated water jets assisted by air has been studied. Sprays with flash atomization have been photographed at various water and air flow rates and water superheats. It has been found that the spray angle with flash atomization increases with water superheat and water flow rate but decreases with air flow rate. The degree of change of spray angle has been analyzed and correlated as a function of superheat, air and water flow rates.

• International Journal of Automotive Technology
• /
• v.4 no.4
• /
• pp.157-164
• /
• 2003

An experimental and numerical study was performed to investigate the macroscopic and microscopic atomization characteristics of high-speed diesel spray issued from the common-rail injection system. For the experiments, spray visualization system and a phase Doppler particle analyzer system were utilized to obtain the spray atomization characteristics such as the process of spray development, spray tip penetration, and SMD distribution. In order to analyze the process of spray atomization with KIVA-3 code, the TAB breakup model is changed to the KH-DDB competition model, which assumes the competition between the wave instability and droplet deformation causes the droplet breakup above the breakup length. The calculated results were also compared with the experiments in terms of spray tip penetration and SMD distribution. The results provide the process of spray development, axial and radial distribution of SMD, and calculated overall SMD as a function of time after start of injection.

• Journal of ILASS-Korea
• /
• v.26 no.4
• /
• pp.189-196
• /
• 2021

Spray drift of agricultural nozzles has become a big issue because it causes low precision targeting and environmental pollution. In order to reduce the spray drift, study spray characteristics of agricultural nozzles is virtually important. In this study, shadowgraph and Mie-scattering visualization techniques were used to study the macroscopic spray and atomization characteristics of an agricultural nozzle. PDPA was used to measure the atomization characteristics of spray. The injection pressure is set to 1 bar, 3 bar and 5 bar, which covers the working range of the nozzle. For the PDPA experiment, 75 points were measured in an area of 160 mm × 120 mm at 10 mm intervals directly below the nozzle to grasp the overall atomization characteristics of the spray. It was found that the spray width and sheet width showed a linear correlation. As the injection pressure increased, the sheet expansion in the 0-degree direction and the sheet swing in the 90-degree direction jointly promoted the breakup of the sheet. In addition, the area close to the central axis had a large droplet velocity, and since a large droplet velocity promoted atomization of spray, the area close to the central axis had a smaller spray droplet diameter than the left and right regions.

• International Journal of Automotive Technology
• /
• v.6 no.1
• /
• pp.9-14
• /
• 2005

An experimental investigation has been carried out to reveal the atomization process of the diesel fuel spray. The spray injected through a single hole nozzle was taken by a camera on the opposite side of a stroboscope for macroscopic observation or a nanolite for microscopic observation. The effect of nozzle aspect ratio was analyzed with disintegration phenomena of the diesel spray. Based on the enlarged spray photograph, atomization process was observed in detail and further the spray cone angle was measured under various ambient pressures. The result shows that atomization of diesel spray in early stage of injection is mainly progressed in the vicinity of spray periphery region except the region close to the nozzle exit and spray head region. The spray cone angle is nearly constant under the pressurized condition, while it decreases with elapsing time under the atmospheric condition.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.11
• /
• pp.1552-1560
• /
• 2001

This paper presents the experimental results of a study undertaken to develop an electrostatic spray system for a combustion application. The characteristics of the liquid atomization and the droplet dispersion in the electrostatic spray of twin fluids were investigated by the optical measurement techniques. The processes associated with the break-up of charged jets were also observed using the laser sheet visualization. The diameter and velocity of droplets were simultaneously measured using the phase Doppler measurement technique. The electrostatic atomization of the liquid fuel depended primarily on the charging voltage and the flow rate, but the dispersion of droplets depended significantly on the aerodynamic flow. Aerodynamic influences on the liquid atomization decreased with an increase of the charging voltage. Consequently, the liquid atomization and the droplet dispersion could be independently controlled using the electrostatic and aerodynamic mechanisms.