• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.6
• /
• pp.1180-1187
• /
• 2010

In the last decade, hydrogen peroxide has received renewed interest as a green propellant which is non-toxic, environmentally clean and relatively easy to handle. This study was performed to acquire the design technique and combustion performance of a 200N bi-propellant engine using hydrogen peroxide and kerosene. The engine which used a catalytic ignition method was designed and cold flow tests were carried out to investigate atomization characteristics. Combustion tests including a pulse mode operation were performed to investigate the combustion performance on various O/F ratios. The results showed that the combustion efficiency and the repeatability of the engine performance were enough to use as an essential database for the development of a high performance engine.

• Journal of ILASS-Korea
• /
• v.16 no.3
• /
• pp.126-133
• /
• 2011

In HCCI Engine, combustion is affected by change of compression speed corresponding to engine speed. The purpose of this study is to investigate the mechanism of influence of engine speed on HCCI combustion characteristics by using numerical analysis. At first, the influence of engine speed was shown. And then, in order to clarify the mechanism of influence of engine speed, results of kinetics computations were analyzed to investigate the elementary reaction path for heat release at transient temperatures by using contribution matrix. In results, as engine speed increased, in-cylinder gas temperature and pressure at ignition start increased. And ignition start timing was retarded and combustion duration was lengthened on crank angle basis. On time basis, ignition start timing was advanced and combustion duration was shortened. High engine speed showed higher robustness to change of initial temperature than low engine speed. Because of its high robustness, selecting high engine speed was efficient for keeping stable operation in real engine which include variation of initial temperature by various factors. The variation of engine speed did not change the reaction path. But, as engine speed increased, the temperature that each elementary reaction would be active became high and reaction speed quicken. Rising the in-cylinder gas temperature of combustion start was caused by these gaps of temperature.

• Journal of ILASS-Korea
• /
• v.19 no.2
• /
• pp.69-74
• /
• 2014

The comparison of the flow characteristics between circular and swirl jets which were controlled by the spinner attachment inside the airtube were conducted in this study. Swirl jet means a flow in whirls by mixing the flow of axial and tangential direction. Swirl flow has been used for the improvement of the combustion efficiency in the combustor. This flow is controlled by the spinner which has several vanes inclined by certain angles to the axial direction. In this study, angle of vane $30^{\circ}$ and diameter ratio of outlet to inlet of the airtube 0.73 were made. These spec. should find on the general gun type burner built in the domestic small size boiler. As the flow characteristics, axial and tangential velocities were measured by using the 2-D hot-wire velocimeter system and analyzed statistically. And also this research conducted a practical experiment considering to the attached belongings likes as ignitor, nozzle etc. on the airtube of the gun type burner. As a result, swirl occurred at the occasion of beingness and flow region extended considerably toward the radial direction. But effect of swirl did not transmit to the downstream. And the complicated flow was appeared regardless of the existence of spinner because of the effect of belongings.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.177-180
• /
• 2010

It has been studied the effect of mixture ratio and chamber pressure on variations of discharge coefficients. Combustion experiments of bi-liquid swirl coaxial injectors were conducted at fuel-rich conditions with liquid oxygen and kerosene. Using two types of injectors for the experiments, characteristics of the discharge coefficient have been identified from variations in a diameter of the fuel nozzle and a momentum ratio along with the change of a LOx spray angle. It is concluded that discharge coefficients do not vary because of no change of flame structures from the fact that the fuel swirl chamber is completely filled up with fuel flow.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.300-303
• /
• 2010

This work shows the result of numerical simulation on a reacting flow by varying atomization properties which can be obtained from a injector for a small and low power aircraft gas turbine engine. Because the atomization properties mainly affect on the performance of the engine, a lot of efficiency tests are needed when a new injector is developed. Nowadays researches has been actively performed using computational analysis. Using commercial package CFD-ACE+, basic studies on the reacting flow field have been conducted. Those results show that the reaction rate is increased when higher pressure and wider angle spray condition are used. More smaller parcels can also enhance the fuel-air reaction.

• Journal of the Korea Safety Management & Science
• /
• v.19 no.4
• /
• pp.317-322
• /
• 2017

When the heat flux on the heating surface following changing heat condition in the boiling heat transfer system exceeds critical heat flux, the critical heat flux phenomenon is going over to immediately the film boiling area and then it is occurred the physical destruction phenomenon of various heat transfer systems. In order to maximize the safe operation and performance of the heat transfer system, it is essential to improve the CHF(Critical Heat Flux) of the system. Therefore, we have analysis the effect of improving CHF and characteristics of heat transfer following the nanoparticle coating thickness. As the results, copper nanocoating time are increased to CHF, and in case of nano-coatings are increased spray-deposited coating times more than in the fure water; copper nanopowder is increased up to 6.40%. The boiling heat transfer coefficients of the pure water are increased up to 5.79% respectively. Also, the contact angle is decreased and surface roughness is increased when nano-coating time is increasingly going up.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.5
• /
• pp.477-484
• /
• 2019

As the residence time in the vehicle increases, the passenger desires a pleasant and stable riding environment in addition to the high driving performance of the vehicle. The windshield defrosting performance is one of the performance requirements that is essential for driver's safe driving. In order to improve the defrosting performance of the windshield of a vehicle, relevant elements such as the shape of the defrost nozzle should be appropriately designed. In this paper, CFD based numerical analysis is conducted to improve defrost performance of small electric vehicles. The defrost performance analysis was performed by changing the angle of the defrost nozzle and the guide vane that spray hot air to the windshield of the vehicle. Numerical simulation results show that the defrosting performance is best when the defrost nozzle angle is $70^{\circ}$ and the guide vane installation angle is $60^{\circ}$. Based on the analytical results, the defrosting experiment was performed by fabricating the defrost nozzle and the guide vane. As a result of the experiment, it is confirmed that the frost of windshield is removed by 80% within 20 minutes, and it is judged that the defrost performance satisfying the FVMSS 103 specification is secured.

• FLOWER RESEARCH JOURNAL
• /
• v.19 no.2
• /
• pp.89-95
• /
• 2011

This study was conducted to improve commercial quality of cut spray chrysanthemums 'Charming Eye' and 'Pink Pride' bred in Korea by foliar application of daminozide, suppressing excessive elongation of peduncle caused by high temperature in greenhouse. Applications were made at two floral-bud-developmental stages and concentrations used were 0, 500, 1000, and $2000mg{\cdot}L^{-1}$. As for 'Charming Eye', cut flower length, peduncle diameter, stem diameter, flower bud diameter, and the number of flower buds did not show any significant difference among all treatments including control. However, the suppressing effect of peduncle elongation, widening angle of flower cluster arrangement on apical part, and increasing parallel flower buds in stage I showed better than those in stage II regardless of daminozide concentration. As for 'Pink Pride', cut flower length, peduncle diameter, and stem diameter did not show any significant difference among all treatments including control but angle of flower cluster on apical part increased compared to control as daminozide was sprayed at stage I and II except $2,000mg{\cdot}L^{-1}$ daminozide-sprayed at stage II. The number of flower buds and flower bud diameter showed the greatest increment through $1,000mg{\cdot}L^{-1}$ daminozide-sprayed at stage I and did the least values as sprayed with $2,000mg{\cdot}L^{-1}$ daminozide at stage II. Daminozide also gradually reduced peduncle length in a concentration-dependant manner but elongation of peduncle foliar-sprayed at stage I showed the more suppressing effect than that at stage II. Increasing the number of parallel flower buds showed the best results when sprayed with $2,000mg{\cdot}L^{-1}$ at stage I. In conclusion, we recommended that foliar spraying with $500-1,000mg{\cdot}L^{-1}$ daminozide at stage I and foliar spraying with $1,000-2,000mg{\cdot}L^{-1}$ daminozide at stage I improved cut flower quality of 'Channing Eye' and 'Pink Pride', respectively.

• Journal of Environmental Impact Assessment
• /
• v.22 no.6
• /
• pp.547-556
• /
• 2013

Recently, golf courses have increased over the years because golf became popular leisure sport. Various environmental problems have been then issued by a golf course during constructing and running them. A problem of pesticide, which is serious among various environmental problems, from golf course has harmful effect on surrounding area and makes human suffer from acute and chronic diseases. Pesticides are used for the cost-effective managing of golf course and the amount of pesticides also increases as the number of golf course increase. Since the assessment of pesticides on near-by surrounding has been focused on water and soil media, studies related to atmospheric dispersion have been hardly attempted. The method to assess an impact of pesticide nearby agricultural production by the atmospheric dispersion using AGDISP(AGricultural DISPersal) model was developed and applied to the actual planned golf course located in Hongcheon, Gangwon. For implementing AGDISP, parameters were investigated from the golf course's land use planning map, pesticide spray device, Hong-Cheon weather station and etc. First of all, a kind of pesticide, a form of spraying pesticide, geographical features, weather data, and distance(golf course to plantation) were investigated to understand how to work these parameters in AGDISP. Restricted data(slope angle, droplet size distribution and solar insolation) sensitivity analysis of these parameters to estimate effect of pesticide nearby a plantation and a high relative contribution data of analyzed data was selected for input data. Ethoprophos was chosen as the pesticide used in the golf course and the amounts of pesticide deposition per annual agricultural productions were predicted. The results show that maximum amount of pesticide deposition through atmospheric dispersion was predicted $2.32{\mu}/m^2$ at 96 m where the nearest organic plantation exists. The residues of pesticide were also estimated based on the annul production of the organic and the deposition amount of the pesticide. Consequently, buckwheat, wheat and millet were likely to exceed maximum residue limits for pesticides in foods(MRL) and sorghum, corn and peanut were likely to exceed MRL by organic farming as well.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.7
• /
• pp.773-778
• /
• 2015

Global warming has recently become an issue that has resulted in a growing trend to minimize environmental pollution. The International Maritime Organization (IMO) has shown that the majority of marine atmospheric pollution occurs as a result of emissions from marine vessels. Therefore, the environmental regulations and emission standards regarding marine vessels have gradually become stricter, and the research and development in this area is experiencing significant progress. In this study, a nozzle for a fuel oil scrubber was investigated using computational fluid dynamics (CFD) and particle imaging velocimetry (PIV). Experiments were conducted on scaled-down model of the scrubber to determine its performance, which was then compared with CFD results. Based on the experimental results, it was found that at a spray angle of $66^{\circ}$, the spray velocity at the nozzle was 20.1 m/s. From this comparison, a full-scale scrubber model was analyzed using CFD, and the effect of the positioning of the nozzle was studied.