• Journal of Welding and Joining
• /
• v.12 no.1
• /
• pp.94-101
• /
• 1994

In this study, plasma spraying has been used to produce $TiO_2$ polycrystalline coatings from $TiO_2$ powders. The physical and chemical properties of plasma sprayed $TiO_2$ coatings depend greatly on plasma spraying conditions. The electrical resistivity, oxygen concentration, photocurrent and crystal structure of plasma sprayed $TiO_2$ coating has been studied. The results are as follows: 1. The oxygen loss and electrical conductivity of $TiO_2$ plasma sprayed coatings increased by low pressure and high amount of auxiliary gas, hydrogen in plasma spraying. 2. Oxygen loss increase electrical conductivity, and decrease photocurrent of $TiO_2$ plasma sprayed coatings. 3. Photocurrent of $TiO_2$ plasma sprayed coatings manufactured in atmospheric pressure is higher than that of low pressure.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.150-150
• /
• 2013

Al-Mg films were prepared onto steel sheet according to deposition condition by eco-friendly electron beam vacuum evaporation method. The influence of Al-Mg films on corrosion resistance was evaluated by salt spray test and electrochemical method etc.. From the experimented results, it was found that the Al-Mg films which showed good corrosion resistance tend to have fine structure with homogenious composition distribution. In addition, it was shown that the property of coating films can be improve by controlling thickness ratio and uniform distribution of intermetallic compounds in Al-Mg films.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.242-248
• /
• 1989

The powder properties and sinterability of ZrO2-8m/o Y2O3 prepared by coprecipitation were investigated. The specific surface area and the total pore volume were increased with increasing pH of sediment and using of ethyl alcohol for washing. The powders of prepared by freeze drying method were showed the smallest particle size and lowest agglomerate rate, and the powders obtained from spray drying method were showed porous structure. At 130$0^{\circ}C$, their relative density were 94-96%, so these sintered bodies have revealed high sinterability in spite of low sintering temperature.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.107-111
• /
• 2019

We report the fabrication of a CdS/CuInGaSe (CdS/CIGS) structure with carbon nanotubes and its application as a photocathode for photoelectrochemical water splitting. CIGS thin films were fabricated using co-evaporation by RF magnetron sputtering, while CdS was fabricated by chemical bath deposition. Spray coated multi-wall carbon nanotube (CNT) film on CdS/CIGS thin film was investigated as a photocathode. The CNT-coated CdS/CIGS showed superior photocurrent density and exhibited improved photostability.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.15-15
• /
• 1998

The problem of the impingement of a sonic or a supersonic jet on a flat surface has not only wide applications but has also interesting and very complex flow phenomena. The main applications of this impinging jet include prediction of solid surface erosion, design of launcher systems, stage separation of multi-stage rocket system, V/STOL operations, thermal spray system, and manufacturing technologies of materials. Much have been learned about the supersonic impinging jet flow field but many fundamental questions have not been answered satisfactorily. The problem encompasses many facets of fluid dynamics which, in combination, present the compressibility effect and the viscous-inviscid interaction, coupled with flow separation and reattachment. What is more, there are many flow parameters that have on the impinging jet flow field, for example, Mach number, Reynolds number, pressure ratio, distance between the nozzle exit and flat plate, jet shock structure, nozzle diameter and etc. Thus the existing data on the supersonic impinging jet flow present considerable disagreement in which quantitative comparison between one result and another is often impossible.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.168-169
• /
• 2013

In this study, the chemical resistance of polyurea resin waterproofing and anti-corrosion materials that is applied to the social infrastructure was analyzed. The result in this study will be utilizing as a basic data for establishing the quality standards which are able to judge the chemically resistant characteristic of polyurea resin waterproofing and anti-corrosion materials.

• Carbon letters
• /
• v.9 no.1
• /
• pp.17-22
• /
• 2008

A carbon nanotube (CNT) of diameter ~20 nm has been synthesized by spray pyrolysis of turpentine oil using Ni/Fe catalyst. Pellet of CNTs has been used as a target to produce semiconducting carbon thin film of band gap 1.4 eV. Presence of oxygen pressure in the pulse laser deposition (PLD) chamber helped to control the $sp^3/sp^2$ ratio to achieve the desired band gap. Results are discussed with the help of Raman spectra, SEM TEM micrographs and optical measurements suggest that semiconducting carbon thin film deposited by PLD technique has retained its nanotubes structure except that its diameter has increased from 20 nm to 150 nm.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.396-403
• /
• 2011

In this study, we investigated the mechanical behaviors of layered thermal barrier coatings by indentations. Various single and double-layered thermal barrier coatings were deposited by air plasma spray process using different type of commercialized YSZ (Yttria stabilized zirconia) starting powders. Indentation stress-strain curve, load-displacement curve and hardness of the single and the double-layered thermal barrier coatings were obtained experimentally and analyzed. The indentation damages at the same loads were compared, and thus, the results depend on the structure of each coating. The result indicates improvement in damage resistances from tailoring of layered structures in the component of gas turbine system is expected.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.6
• /
• pp.432-438
• /
• 2017

AZ91D casting alloy requires an advanced plasma anodizing processing because large amount of defects are liable to generate during anodization. In this study, plasma electrolytic oxidation (PEO) of AZ91D Mg alloy was conducted by the application of either constant voltage or current using a pulse mode and its effects on pore formation, surface roughness and corrosion resistance were investigated. The PEO films showed a three-layer structure. The PEO film thickness was found to increase linearly with voltage. The surface roughness, Ra, ranged between $0.2{\mu}m$ and $0.3{\mu}m$. The corrosion resistance increased from RN 3.5 to 9.5 by the PEO treatment when evaluated according to the 72 hour salt spray test. The PEO-treated surface exhibited higher pitting potential than the raw material.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.254-255
• /
• 2006

Powder library of pseudo four components Li-Ni-Co-Ti compounds were prepared for exploring the composition region with the single phase of the layer-type structure by using combinatorial high-throuput preparation system "M-ist Combi" based on electrostatic spray deposition method. The new layer-type compounds were found wider composition region than the previous report. This process is promising way to find multi component functional materials.