• Journal of ILASS-Korea
• /
• v.12 no.1
• /
• pp.58-64
• /
• 2007

The spray characteristics of the oxidizer-rich preburner are investigated. This system is generally operated at an oxidizerfuel mixture ratio of 50. The spray quality and mixing performance are very important for safe combustion. To know the spray characteristics of the oxidizer-rich preburner, we have designed various swirl injectors and measured droplet velocity and size by the PDPA system. The flow discharge coefficient of the fuel orifice is $0.12{\sim}0.21$, oxidizer orifice discharge coefficient is $0.16{\sim}0.28$. From the spray visualization, fuel nozzle spray angle is $15^{\circ}{\sim}25^{\circ}$, oxidizer nozzle spray angle is $65^{\circ}{\sim}85^{\circ}$ and combined spray angle is reduced $2^{\circ}{\sim}5^{\circ}$ compared to the oxidizer nozzle only case. From the PDPA measurement, droplet SMD is $175\;{\mu}m$ at 50 mm and $190\;{\mu}m$ at 100 mm of variant 1 combined case. The number concentration measurement revealed the reason of the droplet diameter increasement with distance. That is due to drop coalescence results from collision of drops which is occurred in dense sprays at a long distance from nozzle orifice exit.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.3 s.258
• /
• pp.283-291
• /
• 2007

The static pressure distribution, atomization characteristics and velocity distribution of tapered nozzle swirl spray is analyzed and then compared with original swirl spray. The static pressure distribution inside the swirl spray is measured using a piezoresistive pressure transducer. Phase Doppler anemometry (PDA) is applied to measure and analyze the droplet size and velocity distribution of tapered nozzle and original swirl spray. The static pressure inside the spray shows the lower value compared to the atmospheric pressure and this pressure drop is getting attenuated as the taper angle is increased. The droplet size of tapered nozzle spray shows similar value compared to the original swirl spray at the horizontal mainstream while it shows increased value at vertical mainstream. The deteriorated atomization characteristics of tapered nozzle spray is improved by applying high fuel temperature injection without causing the spray collapse. The velocity results show that the larger portion of fuel is positioned with higher injection velocity, and the smaller portion of fuel is positioned with lower injection velocity with causing spatially non-uniform mixture distribution.

• Journal of ILASS-Korea
• /
• v.26 no.3
• /
• pp.111-119
• /
• 2021

Deteriorated agricultural diesel engines using mechanical fuel injection systems have low fuel injection pressures. And they are not equipped with an exhaust gas abatement device, so it produces a lot of exhaust gas. Remanufactured used injectors can reduce emissions because spray characteristics are improved. In addition, remanufacturing is environmentally friendly and economical compared to producing new parts. For efficient injector remanufacturing, it is necessary to conduct a comparison experiment on the spray characteristics of an used mechanical injector and a new injector of the same model. In this study, the spray characteristics of the two injectors were compared by performing an injection quantity measurement and a spray visualization experiment. As a result, the used injector had a larger injection quantity, a shorter spray tip penetration, a wider spray angle and a smaller spray area than the new injector.

• Journal of the Korean Society of Industry Convergence
• /
• v.1 no.2
• /
• pp.41-48
• /
• 1998

This experimental study describes atomization characteristics of spray-spray impingement. Effect of the impingement location and angle on the penetration and the sauter mean diameter of the impinged spray were investigated. Experiment were performed under ranging from 50kPa to 250kPa spray pressure, ranging $30^{\circ}C$ to $135^{\circ}C$ angle on the penetration and free spray. In the case of this experimental, sauter mean diameter $D_{32}$ tends to decrease and duration of film disintegration $t_f$ to decrease, when spray pressure and angle on the penetration is increased. Sauter mean diameter $D_{32}$ were about 20% to be smaller compared with a free spray to jet-jet impingement and 30% to be smaller compared with a free spray to spray-spray impingement.

• Journal of ILASS-Korea
• /
• v.6 no.4
• /
• pp.39-48
• /
• 2001

The Gasoline Direct Injection(GDI) system has been highlighted due to the improvement of fuel consumption and the control of exhaust emission from gasoline engines. Main purpose of the present study is to measure spray characteristics of GDSI for real engine application. We have investigated experimentally spray tip penetration, spray angle, tip velocity and spatial spray distribution. Counter-rotating vortex grown on the spray surface plays an important role in the spray characteristics. Accordingly the spray tip penetration and tip velocity do not excess 50mm, 20m/s respectively, under 0.6MPa ambient pressure. the spray cone angle of GDSI have a same tendency to a simplex swirl atomizer.

• 한국연소학회:학술대회논문집
• /
• 2003.05a
• /
• pp.173-178
• /
• 2003

An experimental study is conducted to investigate the effects of fuel temperature on the spray characteristics of a dual-orifice type swirl injector which is used in gas turbines. The major parameters affecting spray characteristics are fuel temperature and injection pressure entering into the injector. Fuel temperature is shown to have strong influence on the spray characteristics especially at a lower temperature. In this study, fuel temperature is varied from $30^{\circ}C$ to $120^{\circ}C$ and injection pressure is altered from 3 to $7 kg_{f}$ /$cm^{2}$. Two kinds of fuel, which have different surface tension and viscosity, are chosen as an atomizing fluid. As a result, injection instability occurs in the low temperature range due to icing phenomenon and the change of fuel properties. As the injection pressure increases, the kinematic viscosity range for stable atomization becomes wider. The factor controlling the SMD of spray is substantially different depending on the fuel temperature range.

• Journal of ILASS-Korea
• /
• v.17 no.4
• /
• pp.210-215
• /
• 2012

This paper This paper presents effect of nozzle hole number on spray characteristics and engine performance. Experiments were conducted to measure spray penetration and SMD distributions using a spray visualization system and PDPA (phase Doppler particle analyzer) system. In addition, engine performance and emission characteristics were measured using a single cylinder engine and emssion measurement systems. Results showed that 8-hole-injector exhibits improved spray performances. Furthermore, soot emission was decreased with 8-hole-injector, compared to that of 6-hole-injector.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.10-17
• /
• 2000

This work presents an investigation of aerodynamic characteristics of fuel spray injected from a high pressure hollow cone swirl injector into a constant volume chamber. Laser tomography visualization was used to interrogate the fuel and air mixing characteristics and the effect of chamber pressure and temperature increase was analyzed, Preliminary results on spray development showed that mixing effect tends to increase with the increase of injection pressure and chamber gas pressure yielding a decrease of spray penetration and an attenuation of well-defined vortex structure. Topological analysis of the spray structure has been performed to initiate the understanding of mixing and vaporization process. For the present experimental conditions fuel injection pressure and chamber gas pressure appear as the dominant factors which govern the transient mixing characteristics. Moreover spray atmixation characteristics are improved by increasing chamber gas temperature.

• Journal of ILASS-Korea
• /
• v.11 no.1
• /
• pp.24-29
• /
• 2006

Spray characteristics produced by conventional and electrostatic pressure-swirl nozzles for an oil burner have been studied, using kerosine as a test liquid. The charge injection mechanism is used to design the electrostatic nozzle, where specific charge density, breakup length, spray angle and mean diameter are measured and analyzed. Three nozzles with orifice diameters of 0.256, 0.308 and 0.333mm at injection pressures of 0.7, 0.9, 1.1 and 1.3 MPa are used in the study. In case of the electrostatic nozzle, voltages ranging from -5 to -12kV are applied. Comparison of the spray characteristics is made between the conventional and electrostatic nozzles. The results showed that, the electrostatic nozzle is superior to the conventional nozzle. This is due the effect of voltage on the liquid surface tension.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.6
• /
• pp.880-887
• /
• 1998

In order to study heat transfer characteristics of spray cooling for the purpose of uniform and soft cooling of high temperature surface a series of experiments for a hot horizontal copper flat plate was performed by downflow spray water using flat spray nozzle. Cooling curves were mea-sured under the various experimental conditions of flow rates and temperatures of cooling water Surface temperature surface heat fluxes and heat transfer coefficients of horizontal upward-facing flat surface were calculated with cooling curves measured at each radial positions near the cooling surface by TDMA method. Generally heat transfer characteristics for spray cooling is simi-lar to boiling phenomenon of pool boiling. The minimum heat flux(MHF) appear at the surface temperature of about ${\Delta}Tsat=250^{\circ}C$ and the critical heat flux(CHF) appear at about ${\Delta}Tsat=250^{\circ}C$.