• 연구논문집
• /
• s.30
• /
• pp.43-56
• /
• 2000

N-IR spectroscopy technology is very useful. And, the technology has wide application range. In the range, we know that single beam type silica analyzer has some handicap. So we were studied Splitted beam type silica analyzer. This dissertation have been discuss about system structure, system fundamentals and performance test. At the test, we were study in the spectral interference of NH3. We know that existing system had some problem. It is structural frailties of single beam type. Therefore we were study for Splitted beam type structure. And we obtain a good result. We have $\pm$5% accuracy and 0.5 ppb level measuring range. But, we have a question. It is ppt level measuring technology by the laser beam spectroscopy.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.187-192
• /
• 2017

We investigated the effects of the CSRR-metamaterial on microstrip comb-line array antennas. Microstrip comb-line array antennas was designed with 12 radiators, gain of 16.09dBi and bandwidth of 0.24GHz in the 24GHz ISM band. The designed antenna had radiation beam perpendicular to the antenna plane, co-polarization gain of 16.09dBi and cross-polarization gain of -10.86dBi. the CSRR-metamaterial increased largely the impedance bandwidth of the antenna from 0.24GHz to 3.6GHz. however as co-polarization gain became 10.08dBi and cross-polarization gain became 14.1dBi, co-polarization was mixed with cross-polarization. And the antenna gain lowered by 1.99dB. On the investigation of the dependence on the split-direction of the CSRR rings, it showed nearly the same characteristics for up-splitted ring used case and down-splitted ring used case. However in the case of arranging up-splitted ring and down-splitted ring in alternation, co-polarization gain decreased to -1.29dBi and cross-polarization gain increased to 13.9dBi, which meant the wave was transited to cross-polarization majority wave.

• Journal of the Korea Institute of Building Construction
• /
• v.4 no.2
• /
• pp.89-95
• /
• 2004

1) As result of specimen with shear reinforcing bar of reinforced concrete beam, ductile coefficient of specimen was high in specimen containing Cockle shells based on non-mixed specimen. In increase rate of specimens, yield strength was similar in specimens containing Cockle shells and non-mixed specimens and maximum strength was higher in specimen containing Cockle shells. 2) To sum up the above experimental results, it is found that using splitted Cockle shells as aggregate for concrete by 10%～ 15% showed the same or higher compressive strength and shear strength as concretes using general aggregate and it can be used as substitute aggregate of concrete. It is considered that for future use of splitted Cockle shells as substitute concrete aggregate, continuous researches of its durability, applicability and economy are needed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.45-56
• /
• 2001

A constant volume combustion chamber is employed to investigate the initial flame kernel development and flame propagation of gasoline-air mixtures with various ignition systems, ignition energy and spark plug electrodes. To do this research, four ignition systems are designed and manufactured, and the ignition energy is controlled by varying the dwell time. Several kinds of spark plugs are also made to analyze the effects of electrodes on flame kernel development. The velocity of flame propagation is measured by the laser deflection method. The output laser beam from He-Ne laser is divided into three parallel beams by a beam splitter. The splitted beams pass through the combustion chamber. They are deflected when contacted with flame front, and the voltage signals from photodiodes change due to deflection. The results show that higher ignition energy raises the flame propagation speed especially under the fuel lean operation. The wider electrode gap, smaller electrode diameter and sharper electrode tip make the speed of the initial flame propagation faster. The speed of the initial flame propagation is affected by electrode material as well. Electrode material with lower melting temperature help the initial flame propagation.

• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.350-355
• /
• 2001

We have investigated characteristics of ZnSe epilayer grown by molecular beam epitaxy(MBE) on semi-insulating(SI) GaAs by using surface photovoltage(SPV). The measurements of SPV were performed with illumination intensity and modulation frequency. The bandgap energy of ZnSe epilayer was determined from derivative surface photovoltage (DSPV). The five states were observed at room temperature(RT), and those states relate to the impurity and defect formed hetero-interface of ZnSe and GaAs during the sample growth. The observed states represented as a tendency of typical extrinsic transition on the increasing illumination intensity. The 1s and 2s signals related to the excitonic absorption were not observed at RT, but those were presented with the splitted of two peaks in the SPV at 80 K. From the modulation frequency dependence, we obtained the junction conductance and capacitance of the sample.

• ETRI Journal
• /
• v.18 no.3
• /
• pp.171-179
• /
• 1996

Fully passivated low noise AlGaAs/InGaAs/GaAs pseudomorphic (PM) HEMT with wide head T-shaped gates were fabricated by dose split electron beam lithography (DSL). The dimensions of gate head and footprint were optimized by controlling the splitted pattern size, dose, and spaces of each pattern. We obtained stable T-shaped gate of $0.15{\mu}m$ gate length with $1.35{\mu}m-wide$ head. The maximum extrinsic transconductance was 560 mS/mm. The minimum noise figure measured at 18 GHz at $V_{ds}=2V andI_{ds}=17mA$ was 0.41 dB with associated gain of 8.19 dB. At 12 GHz, the minimum noise figure and an associated gain were 0.26 and 10.25 dB, respectively. These noise figures are the lowest values ever reported for GaAs-based HEMTs. These results are attributed to the extremely low gate resistance of wide head T-shaped gate having a ratio of the head to footprint dimensions larger than 9.

• Korean Journal of Optics and Photonics
• /
• v.2 no.4
• /
• pp.179-185
• /
• 1991

Twyman-Green interferometer is developed for assessment of IR optical system performance. Light source is $CO_2$ gas laser which has 10.6$\mu \textrm m$ wavelength. The light beam is expanded to 2.5 cm dia by Ge lens and splitted by ZnSe parallel plane plate. One of the beams is reflected by refernce mirror which is operated PZT. The fringe will be detected by a pyro-electric vidicon camera and displayed by a CRT monitor. Here, the IR firinge is recorded on the thermal paper. In visible region, the light source is He-Ne laser. The fringe is detected by a CCD camera and displayed by the CRT monitor. The intensity of the fringe is digitized by a image card and processed by a PC. The wavefront aberration function, PSF and OTF are calculated. The results are displayed in 3-D graphs on the monitor or printed out by a line printer.

• Korean Journal of Optics and Photonics
• /
• v.14 no.6
• /
• pp.613-622
• /
• 2003

The multi-configurative microscopic system for inspecting the wire-bonding of reed frame is designed. Rays refracted by objective lens group which is composed of common lens group of x2 and x6 are splitted by beam-splitter, and Rays through the central region and the boundary region of the object imaged at x2 and x6 through imaging lens groups, respectively. The depth of wire structure on the reed frame has about $\pm$3 mm, in order to observe by uniform magnification without the dependency on the variation of objective distance generated by the depth of wire structure on the reed frame, imaging lens groups should be moved on nonlinear locus like mechanically compensated zoom lenses. The nonlinear equations for zoom locus are derived by using the Gaussian bracket. Refraction powers and positions of each groups are numerically determined by solving the equations, and initial design data for each groups is obtained by using Seidel third order aberration theory. The optimization technique is finally utilized to obtain this microscopic system.