• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.9-14
• /
• 2000

Dielectric characteristics of P(VDF/TrFE) film manufactured using spin coating technique have been investigated. To improve the crystallinity and quality of film, the film was three step annealed. Simple etching process and conditions for P(VDF/TrFE) film were established using top electrode as a mask. Poling is performed by several steps. $1.87\;{\mu}m$ thick P(VDF/TrFE) films were obtained with conditions such that the solution of 10 wt% concentration was spun at 3000rpm for 30 seconds. Before poling, dielectric constant and dielectric loss of P(VDF/TrFE) film were 13.5 and 0.042, respectively. After poling, dielectric constant and dielectric loss of P(VDF/TrFE) film were 11.5 and 0.037, respectively.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1022-1024
• /
• 1995

In this study, $Pb(Zr_xTi_{1-x})O_3$(x=0.65, 0.52, 0.35) thin films were fabricated by Sol-Gel method. A stock solution with excess Pb 10[mol.%] of $Pb(Zr_xTi_{1-x})O_3$ was made and spin-coated on the Pt/$SiO_2$/Si substrate at 4000[rpm] for 30[sec.]. Coated specimens were dried on the hot-plate at $400[^{\circ}C]$ for 10[min.]. Sintering temperature and time were $500{\sim}800[^{\circ}C]$ and $1{\sim}60$[min.]. To investigate crystallization condition, PZT thin films were analyzed with sintering temperature, time and composition by the XRD. The microstructure of thin films were investigated by SEM. The ferroelectric perovskite phases precipitated under the sintering of $700[^{\circ}C]$ for 1 hour. In the PZT(52/48) composition, dielectric constant and dielectric loss were 2133, 2.2[%] at room temperature, respectively.

• Electrical & Electronic Materials
• /
• v.9 no.2
• /
• pp.132-137
• /
• 1996

Pb(Zr$_{x}$Ti$_{1-x}$ )O$_{3}$ solutions prepared by sol-gel processing with different Zr/Ti ratio were coated on Pt/SiO$_{2}$/Si substrates using spin coating method. Coated films were annealed by rapid thermal annealing at 650.deg. C for 20sec to fabricate Pb(Zr, Ti)O$_{3}$ ferroelectric thin films. Electrical properties of the films such as dielectric constant and loss, ferroelectric hysteresis, fatigue, switching time, and leakage current were measured. Hysteresis of the films with different Zr/Ti ratio yield Pr ranging 10-21.mu.C/cm$^{2}$, E$_{c}$ ranging 37.5-137.5kV/cm. Hysteresis curve was changed from square-type to slim type according to increasing Zr contents. Switching time was faster than 180ns, and leakage current was about 20.mu.A/cm$^{2}$. The film underwent above 10$^{8}$ cycles of reversed polarization showed fatigue with increased coercive field and decreased remnant polarization.tion.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.6
• /
• pp.486-491
• /
• 2002

We have fabricated $Bi_{3.25}La_{0.75}Ti_3O_12$ (BLT) thin films on the Pt/Ti/$SiO_2$/Si substrates using a metalorganic decomposition (MOD) method with annealing temperature from $550^{\circ}C$ to $750^{\circ}C$. The structural properties of BLT films examined by x-ray diffraction (XRD). From XRD analysis. BLT thin films show polycrystalline structure. The layered-perovskite phase was obtained by spin-on films at above $600^{\circ}C$ for 1h. Scanning electron microscopy (SEM) showed uniform surface composed of rodlike grains. The grain size of BLT films increased with increasing annealing temperature. The BLT film annealed at $650^{\circ}C$ was measured to have a dielectric constant of 279, dielectric loss of 1.85(%), remanent polarization of $25.66\mu C/\textrm{cm}^2$, and coercive field of 84.75 kV/cm. The BLT thin films showed little polarization fatigue test up to $3.5{\times}10^9$ bipolar cycling at 5 V and 100 kHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.14-16
• /
• 1995

Pb($Zr_{0.52}Ti_{0.48}$)$O_3$ ceramic thin films were fabricated from an alkoxide-based solution by Sol-Gel method. Pb($Zr_{0.52}Ti_{0.48}$)$O_3$ co-ramic thin films were formed by spin coating method on Pt/$SiO_2$/Si substrate at 4000[rpm] for 30 [sec]. Coated specimens were dried on the hot-plate at 400[$^{\circ}C$] for 10[min]. The coating process was repeated 6 times and then sintered at temperature between 500 ~ 800[$^{\circ}C$] for 1 hour. The ferroelectric perovskite phases precipitated under the sintering of 700[$^{\circ}C$] for 1 hour. Pb($Zr_{0.52}Ti_{0.48}$)$O_3$ thin film sintered at 700[$^{\circ}C$] for 1hour showed good dielectric constant (2133) and dielectric loss (2.2[%]) Properties. The switching voltage, switching time and leakage currents density were 3.0[V], 1.7[${\mu}$sec] , 160[pA/$\textrm{cm}^2$] repectively.

• Journal of Sensor Science and Technology
• /
• v.12 no.1
• /
• pp.10-15
• /
• 2003

$PbTiO_3$/P(VDF/TrFE) thin film for pyroelectric infrared sensor's sensing materials have been fabricated by spin coating technique. 65 wt% VDF and 35 wt% TrFE were for P(VDF/TrFE) powder. $PbTiO_3$ powder was used for a ceramic - polymer composites materials. Surface of composite thin film by ceramic fraction factor was observed by SEM. The $PbTiO_3$/P(VDF/TrFE) thin film capacitancy, dielectric constant and dielectric loss measured by impedence analyzer(HP4192A) and pyroelectric coefficient was measured by semiconductor parameter analyzer(HP4145B).

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.57
• /
• pp.111-135
• /
• 2013

This study analyzes some important spin-off effects of the provision, UCP600 Article 14(6), through the methodology of the expected utility maximization theory based on the state-contingent commodities model. Some technical implications of this study are as follows. First, the risk-averse beneficiary will choose to present his documents more than 5 days before expiry date by paying a higher risk premium (so-called cure period) for full assurance to cure documentary discrepancies, if expressed economically, he pursues loss reducing activities to the point where the expected marginal product of his activities is less than its marginal cost. Secondly, where the effectiveness of securing cure period is uncertain, the risk-averse beneficiary will choose to present documents just on the expiry date without securing any cure period by paying no risk premium. This study finally suggests the safe harbor standard should be optimal solution only if it is supplemented by the hidden reasonableness standard for balancing the conflicts of interest between beneficiaries and banks.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.11
• /
• pp.895-899
• /
• 2011

Multiferroic BFO/PZT(5/95) multilayer films were fabricated by spin-coating method on the Pt/Ti/$SiO_2$/Si substrate alternately using BFO and PZT(9/95) alkoxide solutions. The structural and dielectric properties were investigated with variation of the solvent and the number of coatings. All films showed the typical XRD patterns of the perovskite polycrystalline structure without presence of the second phase such as $Bi_2Fe_4O_3$. BFO/PZT multilayer thin films showed the typical dielectric relaxation properties with increase an applied frequency. The average thickness of 6-coated BFO/PZT multilayer film was about 600 nm. The dielectric properties such as dielectric constant, dielectric loss and remnant polarization were superior to those of single composition BFO film, and those values for BFO/PZT multilayer film were 1199, 0.23% and 12 ${\mu}C/cm^2$.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1434-1436
• /
• 1996

In this study, ferroelectric $PbTiO_3$ thin films were deposited on the Pt/$SiO_2$/Si substrate by Sol-Gel method. $PbTiO_3$ stock solution was made and spin-cooled at 4000[rpm] for 30[sec.]. Coated specimens were dried at $400[^{\circ}C]$ for 10[min.] and then annealed at $500{\sim}800[^{\circ}C]$ for 1 hour. Annealing temperature were examined to optimize micro structural and dielectric properties of the films. The ferroelectric perovskite phase was observed in the file annealed at $700[^{\circ}C]$ for 1 hour. In the case of $PbTiO_3$ thin films annealed at $700[^{\circ}C]$ for hour, dielectric constant and dielectric loss showed the good value of 324, 2.0[%], respectively.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.335-337
• /
• 1995

In this study, $Pb(Zr_{0.52}Ti_{0.48})O_3$ ceramic thin films were fabricated from an alkoxide-based by Sol-Gel method. $Pb(Zr_{0.52}Ti_{0.48})O_3$ stock solution was made and spin-coated on the $Pt/SiO_2/Si$ substrate at 4000[rpm] for 30[sec]. Coated specimens were dried at 400[$^{\circ}C$] for 10 [min]. The coating process was repeated 4 times and then heat-treated at 500$\sim$800[$^{\circ}C$], 1 hour. The final thickness of the thin films were about 3000[A]. The crystallinity and microstructure of the thin films were investigated for varing the sintering condition. The ferroelectric perovskite' phases precipitated under the sintering of 700[$^{\circ}C$] for 1 hours. In the $Pb(Zr_{0.52}Ti_{0.48})O_3$ thin films sintered at 700[$^{\circ}C$] for 1 hour, dielectric constant and dielectric loss were 2133, 2.2[%] at room temperature, respectively. $Pb(Zr_{0.52}Ti_{0.48})O_3$ thin film capacitors having good dielectric and electrical properties are expected for the application to the dielectric material of DRAM.