• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.709-714
• /
• 2003

에틸렌글리콜을 용매로 하여 용매열 합성으로 20$0^{\circ}C$에서 3-5시간 반응시킨 후 1000-140$0^{\circ}C$에서 2-4시간동안 대기 중에서 열처리 과정으로 Eu가 도핑된 $Y_2$ $O_3$ 나노 입자는 제조되었다. 100$0^{\circ}C$에서 열처리한 결정의 X-선 회절패턴은 보고되어진 데이터(JCPDS 카드파일 41-1105, a=10.6041 $\AA$)와 거의 일치하는 격자상수 a=10.5856 $\AA$으로 순수한 큐빅 $Y_2$ $O_3$ 상을 나타내었다. 제조된 적색 형광체의 평균입자의 크기는 대략 100 nm로 구형의 형태를 가진다 열처리 온도가 증가함에 따라 형광체 입자의 크기가 감소하였고, 열처리 온도가 증가함에 따라 형광체의 발광 세기가 증가하였다. PL 스펙트럼 분석을 통해 Eu의 농도가 3 ㏖% 도핑된 $Y_2$ $O_3$은 250 nm 파장에서 여기 스펙트럼을 나타내었고 611 nm 파장에서 주발광 스펙트럼을 나타내었다.

• Journal of Mechanical Science and Technology
• /
• 제14권10호
• /
• pp.1131-1142
• /
• 2000

In an effort to illustrate the global variation of SMD (Sauter mean diameter, or $D_{32}$) and AMD (Arithmetic mean diameter, or $D_{10}$) at five axial downstream locations (i. e., at Z=30, 50, 80, 120, and 170 mm) under the different experimental conditions, the radial coordinate is normalized by the spray half-width. Experimental data to analyze the atomization characteristics concerning with an internal mixing type have been obtained using a PDPA(Phase Doppler Particle Analyzer). The air injection pressure was varied from 40 kPa to 120 kPa. In this study, counterflowing internal mixing nozzles manufactured at an angle of $15^{\circ}$with axi-symmetric tangential-drilled four holes have been considered. By comparing the results, it is clearly possible to discern the effects of increasing air pressure, suggesting that the disintegration process is enhanced and finer spray droplets can be obtained under higher air assist. The variations in $D_{32}$ are attributed to the characteristic feature of internal mixing nozzle in which the droplets are preferentially ejected downward with strong axial momentum, and dispersed with the larger droplets which are detected in the spray centerline at the near stations and smaller ones are generated due to further subsequent breakup by higher shear stresses at farther axial locations. The poor atomization around the centre close to the nozzle exit is attributed to the fact that the relatively lower rates of spherical particles are detected and these drops are not subject to instantaneous breakup in spite of the strong axial momentum. However, substantial increases in SMD from the central part toward the edge of the spray as they go farther downstream are mainly due to the fact that the relative velocity of droplet is too low to cause any subsequent disintegration.

• Journal of Microbiology and Biotechnology
• /
• 제28권10호
• /
• pp.1664-1670
• /
• 2018

Titanium dioxide ($TiO_2$) has wide applications in food, cosmetics, pharmaceuticals and manufacturing due to its many properties such as photocatalytic activity and stability. In this study, the biosynthesis of $TiO_2$ nanoparticles (NPs) was achieved by using Baker's yeast. $TiO_2$ NPs were characterized by X-ray Diffraction (XRD), UV-Visible spectroscopy, Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and Energy Dispersive X-ray analysis (EDX) studies. The XRD pattern confirmed the formation of pure anatase $TiO_2$ NPs. According to EDX data Ti, O, P and N were the key elements present in the sample. SEM and TEM revealed that the nanoparticles produced were spherical in shape with an average size of $6.7{\pm}2.2nm$. The photocatalytic activity of $TiO_2$ NPs was studied by monitoring the degradation of methylene blue dye when treated with $TiO_2$ NPs. $TiO_2$ NPs were found to be highly photocatalytic comparable to commercially available 21 nm $TiO_2$ NPs. This study is the first report on antimicrobial study of yeast-mediated $TiO_2$ NPs synthesized using $TiCl_3$. Antimicrobial activity of $TiO_2$ NPs was greater against selected Gram-positive bacteria and Candida albicans when compared to Gram-negative bacteria both in the presence or absence of sunlight exposure. $TiO_2$ NPs expressed a significant effect on microbial growth. The results indicate the significant physical properties and the impact of yeast-mediated $TiO_2$ N Ps as a novel antimicrobial.

• Journal of Microbiology and Biotechnology
• /
• 제14권1호
• /
• pp.182-187
• /
• 2004

Strain NR $15-1^T$ isolated from traditional Korean Nuruk is described as a new species and named as Aspergillus coreanus NR $15-1^T$ sp. novo Strain NR $15-1^T$ grew rapidly to form yellow-green colonies whose surfaces were velvety on Czapek solution agar. Conidial heads were yellow to light and elliptical, whereas the conidiophore was colorless and typically long. In addition, vesicles were from flask-shaped to globose, and sterigmata are uniseriate. Conidia were spherical and deep yellow-green, and their surfaces were lightly roughened. The G＋C content of strain NR $15-1^T$ was 51 mol% and strain NR $15-1^T$contained a dihydrogenated ubiquinone with Q9 (94.9%) as a major quinone. The nucleotide sequences of strain NR $15-1^T$ in the two Internal Transcribed Spacers (ITS 1 and 2) and 5.8S rDNA showed highest similarity when compared with that of A. tubingensis and A. phoenicis NRRL $365^T$. However, based on morphological and chemotaxonomic characteristics, this strain was different from A. tubingensis and A. phoenicis NRRL $365^T$. On the basis of the data presented, it is proposed that strain NR $15-1^T$ should be placed in the genus Aspergillus as a new species, Aspergillus coreanus sp. novo Therefore, the type strain of the new species is strain NR $15-1^T$ (=KCTC 18075P^T,=KCCM 80006^T$.

• Applied Microscopy
• /
• 제47권2호
• /
• pp.70-74
• /
• 2017

In the case of genus Nothobranchius, Nothobranchiidae, the morphology of fertilized eggs and ultrastructures of fertilized egg envelopes have been reported in only two fishes. Therefore it is hard for sure to these morphological characteristics show genus specificity because of lower research samples. So, we studied the morphology of fertilized egg, and compared the ultrastructures of outer surface, micropyle, and section of fertilized egg envelopes under the light and electron microscopes from the other two species, Nothobranchius foerschi and Nothobranchius rachovii, Nothobranchiidae to find out whether these structures have the species specificity or not. Both fertilized eggs were spherical, demersal and adhesive, and have a large oil droplet. The adhesive whip-like structures were distributed on the outer surface of egg envelope, and a micropyle located on the animal pole. The fertilized egg envelope consisted of two distinct layers: an outer electron-dense layer with adhesive structures and an inner lamellae layer in both species. The external shapes of fertilized egg and ultrastuctures of outer surface, micropyle, and section of fertilized egg envelope have same structure including results before. Our data indicate that these morphological characteristics of fertilized egg and fertilized egg envelope show genus Nothobranchius specificity.

• 한국분말재료학회지
• /
• 제14권5호
• /
• pp.281-286
• /
• 2007

Ordered $L1_0$ to FePt nanoparticles are strong candidates for high density magnetic data storage media because the $L1_0$ phase FePt has a very high magnetocrystalline anisotropy $(K_u{\sim}6.6-10{\times}10^7erg/cm^3)$, high coercivity and chemical stability. In this study, the ordered $L1_0$ FePt nanoparticles were successfully fabricated by chemical vapor condensation process without a post-annealing process which causes severe particle growth and agglomeration. The $Fe_{50}Pt_{50}$ nanopowder was obtained when the mixing ratio of Fe(acac) and Pt(arac) was 2.5 : 1. And the synthesized FePt nanoparticles were very fine and spherical shape with a narrow size distribution. The average particle size of the powder tended to increase from 5 nm to 10 nm with increasing reaction temperature from $800^{\circ}C$ to $1000^{\circ}C$. Characterisitcs of FePt nanopowder were investigated in terms of process parameters and microstructures.

• 한국음향학회지
• /
• 제24권3호
• /
• pp.166-170
• /
• 2005

본 논문은 근접장 음향 홀로그래피를 이용한 수중 음원의 위치를 추정하는 기술에 대한 것이다. 수중 소음원의 식별에 적용 가능함을 실험으로 검증하고 그 결과를 기술하였다. 실험에 사용된 음원은 2개의 구형 센서로 구성되고 음원의 근거리 음압은 음원과 근접된 위치에 설정된 홀로그램 평면에서 측정된다. 측정된 음압에 대한 상호전력 스펙트럼으로부터 홀로그램 평면에서의 복소음압을 구하고 이를 공간 변환하여 음원 영역에서의 음장분포를 구하였다. 음원 영역에서의 음장분포 결과는 음원의 위치와 발생된 음원준위의 크기를 가시적으로 보여주며, 실험 결과는 음원의 위치와 음원준위의 상대적인 크기를 정확하게 추정하고 있어 근접장 음향 홀로그래피를 이용하여 수중 소음원의 위치 추정과 개별 소음원의 기여도 분석이 가능함을 확인하였다.

• 태양에너지
• /
• 제12권3호
• /
• pp.47-59
• /
• 1992

산업용 노의 폐열 회수를 위하여 노의 배기부에 설치되는 복사형 레큐페레이터 중에서 가장 대표적인 형태인 이중 원관식 레큐페레이터의 열전달 특성에 관하여 연구하였다. 내관에는 고온의 배기가스가 흐르고, 내관과 외관 사이의 환상공간에서는 공기가 흐르며 외관의 외벽면은 단열되어 있는 원관 식 레큐퍼레이터의 열전달특성을 규명하였다. 고온의 배기가스 폐열은 내관의 내벽으로 전달되고 이는 다시 환산 공간내의 공기로 전달된다. 배기가스의 복사 열전달은 구 조화 근사법을 사용하여 모델링한 후 이를 유동장과 연계하여 수치적으로 해석하였으며, 기존의 실험적연구와 일치하는 조건에서의 계산결과와 비교하였다. 또한, 내관의 동심축 상에 원동통형의 재복사기를 설치할 경우 내관에서 재복사 효과가 일어나는데 이에 따른 열전달 특성을 연구하여 레큐퍼레이터를 이론적으로 해석할 수 있는 방법을 제시하였다.

• International Journal of Oral Biology
• /
• 제34권1호
• /
• pp.37-42
• /
• 2009

The attachment and adhesion of RAW 264.7 and MC3T3-E1 cells to titanium (Ti) discs with various degrees of roughness was investigated. The attachment, adhesion, and proliferation of these cells were evaluated after 4 hr, 24 hr and 7 day incubations. Both RAW 264.7 and MC3T3-E1 cells showed a time-dependant correlation between attachment and adhesion on the surface of the titanium discs. Both types of cells tended to have higher survival rate on these discs as the surface roughness increased. The percentage of adherent inflammatory RAW 264.7 cells was greater than MC3T3-E1 cells at 24 hr, but this was reversed at 7 days in culture. The morphology of osteoblastic MC3T3-E1 cells at 24 hr, determined using a surface emission microscope (SEM), appeared flattened and spread out while inflammatory RAW 264.7 cells were predominantly spherical in shape. The adhesion of both cell types on the titanium discs was dependant on the levels of fibronectin adsorbed on the disc surface, indicating that serum constituents modulate the efficient adhesion of these cells. Our data indicate that the cellular response to the titanium surface is dependent on the types of cells, surface roughness and serum constituents.

• Journal of Radiation Protection and Research
• /
• 제41권3호
• /
• pp.237-244
• /
• 2016

Background: Korea Atomic Energy Research Institute is developing a fission product transport module for predicting the behavior of radioactive materials in the primary cooling system of a nuclear power plant as a separate module, which will be connected to a severe accident analysis code, Core Meltdown Progression Accident Simulation Software (COMPASS). Materials and Methods: This fission product transport (COMPASS-FP) module consists of a fission product release model, an aerosol generation model, and an aerosol transport model. In the fission product release model there are three submodels based on empirical correlations, and they are used to simulate the fission product gases release from the reactor core. In the aerosol generation model, the mass conservation law and Raoult's law are applied to the mixture of vapors and droplets of the fission products in a specified control volume to find the generation of the aerosol droplet. In the aerosol transport model, empirical correlations available from the open literature are used to simulate the aerosol removal processes owing to the gravitational settling, inertia impaction, diffusiophoresis, and thermophoresis. Results and Discussion: The COMPASS-FP module was validated against Aerosol Behavior Code Validation and Evaluation (ABCOVE-5) test performed by Hanford Engineering Development Laboratory for comparing the prediction and test data. The comparison results assuming a non-spherical aerosol shape for the suspended aerosol mass concentration showed a good agreement with an error range of about ${\pm}6%$. Conclusion: It was found that the COMPASS-FP module produced the reasonable results of the fission product gases release, the aerosol generation, and the gravitational settling in the aerosol removal processes for ABCOVE-5. However, more validation for other aerosol removal models needs to be performed.