• Applied Chemistry for Engineering
• /
• v.20 no.4
• /
• pp.396-401
• /
• 2009

A micro-spherical activated carbon with meso-pore structure of 52~64% and particle diameter of $2{\sim}10{\mu}m$ was prepared for the improvement electrochemical performance of activated carbon as electrode material for electric double layer capacitor. Resorcinol-formaldehyde resin was used as a carbon source in this preparation. According to electrochemical analysis of EDLC using this activated a carbon with showing effects to reduce charge transfer resistance and to increase rate capability, it was found out that micro-spherical activated carbon could be a good method as well as a material for enhancing the performance of electric double layer capacitor.

• Solar Energy
• /
• v.17 no.2
• /
• pp.67-74
• /
• 1997

Spherical shape of phase change material(PCM) has been prepared by using sodium acetate trihydrate as a latent heat storage medium. Gelatin was used as an effective thickener to prevent undesirable phase separation. Sodium pyrophosphate decahydrate was used as nucleator to decrease the degree of supercooling in the thickened phase change material. Spherical PCM particles of 3-3.5 mm in diameter continuously manufactured with molten PCM with those conditions. The particle size of PCM was not affected by the effluent velocity of molten PCM in range of 1.3-1.8 ml/min. DSC, SEM and XRD were also used to characterize the properties of PCM particles.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.8
• /
• pp.657-663
• /
• 2012

The spherical mesoporous silica is synthesized and incorporated with CdSe/ZnS quantum dots(QDs) for preparing micro beads to detect toxic and bio-materials with high sensitivity. The spherical silica beads with the brunauer-emmett-telle(BET) average pore size of 15 nm were prepared with a ratio 1, 3, 5-trimethylbenzen, as a swelling agent, to the block-copolymer template surfactant of over 1 and under vigorous mixing condition. The surface of spherical mesoporous silica is modified using octadecylsilane for incorporating QDs. Based on photoluminescence(PL) spectra, the relative brightness of mesoporous silica beads incorporated with 10 nM of QDs is 79,000 times brighter than that of Rodamine 6 G.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.44-47
• /
• 2003

In this paper, the electric field distribution in dielectric tube with one layer and spherical dielectric($ZrO_2$) in water was simulated. The reactor was made up of the spherical dielectric that is diameter : 3.0[mm], $ZrO_2(\varepsilon_r:10)$ and one glass plate of thickness(2[mm]), $\varepsilon_r$(10) as electrode. The discharge gap was 8[mm]. To get more strong electric field, the dielectric constant should be higher comparatively. Using the spherical dielectric for water discharge in dielectric tube, the location of equipotential line was shifting from the interior to the exterior. At real water discharge experimental, ozone was measured higher dissolved ozone in water at condition of water rate(l[l/min]) and injector than condition of non-injector or 2~3[l/min].

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.40-43
• /
• 2003

In this paper, the electric field distribution in dielectric tube with one layer and spherical dielectric(glass) in water was simulated. The reactor was made up of the spherical dielectric that is diameter : 3.0[mm], glass(${\varepsilon}_r$:5) and one glass plate of thickness(2[mm]), ${\varepsilon}_r$(5) as electrode. The discharge gap was 8[mm). Toget more strong electric field, the dielectric constant should be higher comparatively. Using the spherical dielectric for water discharge in dielectric tube, the location of equipotential line was shifting from the interior to the exterior. At real water discharge experimental, $H_2O_2$ was measured higher generated $H_2O_2$ in water at condition of water rate(1[l/min]) and injector than condition of non-injector or 2-3[l/min])

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.217-220
• /
• 2003

The effective thermoelastic properties of porous metals are discussed herein after each material forming process such as hot pressing or extrusion. The voids in metal matrix are assumed to be initially spherical in shape and to be distributed randomly. Once the porous material deforms plastically due to each material forming process, the voids change their shape from a sphere to an ellipsoid and align in one direction. Since the voids are compressible in nature, the void volume fraction is assumed to be decreasing during each material forming process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.380-386
• /
• 2002

Damage behaviors induced in silicon carbide by an impact of particle having different material and size were investigated. Especially, the influence of the impact velocity of particle on the cone crack shape developed was mainly discussed. The damage induced by spherical impact was different depending on the material and size of particles. Ring cracks on the surface of specimen were multiplied by increasing the impact velocity of particle. The steel particle impact produced larger ring cracks than that of SiC particle. In the case of high velocity impact of SiC particle, radial cracks were produced due to the inelastic deformation at the impact site. In the case of the larger particle impact, the damage morphology developed was similar to the case of smaller particle one, but a percussion cone was farmed from the back surface of specimen when the impact velocity exceeded a critical value. The zenithal angle of cone cracks developed into SiC material decreased monotonically with increasing of the particle impact velocity. The size and material of particle influenced more or less on the extent of cone crack shape. An empirical equation, $\theta$= $\theta$$\sub$st/, v$\sub$p/(90-$\theta$$\sub$st/)/500 R$\^$0.3/($\rho$$_1$/$\rho$$_2$)$\^$$\frac{1}{2}$/, was obtained as a function of impact velocity of the particle, based on the quasi-static zenithal angle of cone crack. It is expected that the empirical equation will be helpful to the computational simulation of residual strength in ceramic components damaged by the particle impact.

• Bulletin of the Korean Chemical Society
• /
• v.12 no.3
• /
• pp.322-328
• /
• 1991

We have studied a characterization method of accurate size of spherical particles by fitting experimental light scattering profile to the rigorous theoretical scattering function. An efficient software has been developed for computation of the theoretical scattering function and regression analysis. A light scattering instrument has been built and the necessary data acquisition and analysis are carried out by use of a personal computer with an emphasis on the reduction of analysis and time aiming that this study will be extended toward a development of a practical particle sizing apparatus. The performance of the instrument and the software has been evaluated with latex spheres and found to be satisfactory.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.19-19
• /
• 2009

Recently, Light Emitting Diode(LED) has many advantages in comparison with conventional light sources; low power consumption, long lifetime, and less environmental pollution. Therefore, the use of LED is multiplying and increasing rapidly. In general, however, spherical lens is used in LED-lighting which cause many problems induces by optical aberration of spherical lens; low illumination, a yellow belt, unpleasant feeling in human eye. As a potential solution of this problem, aspherical lens can be employed. This study reports the improvement of LED-lighting performance by adopting aspherical lens. From the commercial program, $LightTools^{TM}$, the optical problem were ensured. And then, to improve this problem, optimum aspheric form was designed using Code $V^{TM}$.

• Structural Engineering and Mechanics
• /
• v.53 no.4
• /
• pp.661-679
• /
• 2015

In this article, nonlinear finite element solutions of bending responses of functionally graded spherical panels are presented. The material properties of functionally graded material are graded in thickness direction according to a power-law distribution of volume fractions. A general nonlinear mathematical shallow shell model has been developed based on higher order shear deformation theory by taking the geometric nonlinearity in Green-Lagrange sense. The model is discretised using finite element steps and the governing equations are obtained through variational principle. The nonlinear responses are evaluated through a direct iterative method. The model is validated by comparing the responses with the available published literatures. The efficacy of present model has also been established by demonstrating a simulation based nonlinear model developed in ANSYS environment. The effects of power-law indices, support conditions and different geometrical parameters on bending behaviour of functionally graded shells are obtained and discussed in detail.