• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.361-364
• /
• 2002

This paper discusses the influencing factors such as coring position, height to diameter ratio of core specimen(h/d) and coring torque on the strength estimation of concrete by small site coring method in order to verify the validities of small size core method. According to results, as for the influence of drilling position, when core specimens are obtained from the place parallel to placing direction, compressive strength of core specimens are higher than those perpendicular to placing direction. This is due to the loss of the area of core specimen perpendicular to plating direction by bleeding. And in case of $\phi$ 24mm core specimen, when vertical drilling against placing direction is taken. compressive strength of core specimen obtained at the bottom of the structure is higher than that at the top of the structure. As for the influence of height to depth ratio, as h/d ratio increases compressive strength shows to be decreased. As for the influences of rotation speed of drilling machine, as its speed goes up, compressive strength decreases, regardless of core diameter.

• 연구논문집
• /
• s.26
• /
• pp.43-50
• /
• 1996

Present paper describes on/off design performance analysis of an 74KW industrial turboshaft gasturbine engine. Procedures to match between the compressor, combustor and turbine have been incorporated into the developed program satisfying compatibility requirement of flow and work and ratational speed. The validity of the performance results from the developed program are yet to be proved through performance experiments of the resultant engine, but comparison of the present results with those from "GASCAN(Thermoflow:America) under similar mass inlet flow, pressure ratio, and speed condition show good agreement despite present results underpredict 6-10% for power and up to 3% in efficiency, respectively.

• Korean Journal of Food Science and Technology
• /
• v.15 no.4
• /
• pp.392-398
• /
• 1983

A pilot single-screw food extruder was constructed, and its mechanical properties and product characteristics were investigated by using corn grits. The screw rotational speed was varied and the changes in temperature profile of the barrel for the start-up period of operation were measured. The rate of heat generation for the start-up period was affected by the screw speed and feed rate. The screw speed resulted in a great influence on the estimated dough viscosity. The changes in the dough viscosity could indicate the on-set of termoplastic reaction in the barrel. The expansion ratio during the start-up period mainly depended on the barrel temperature and the degree of thermoplastic reaction in the barrel. The barrel temperatures for the gelatinization and burning of corn grits depended on the screw speed as well as the feed rate.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.05a
• /
• pp.45-51
• /
• 2000

Investigators who study on combustion in the cylinders of reciprocating piston type internal combustion engines have been encountered embarrassments due to the difficulties of adjusting specific parameter without interfacing other parameters such as cylinder wall temperature composition of gas in the cylinder existence of cylinder lubricant etc. Rapid compression-expansion machine the position and speed of piston of which are able to be controlled by means of a system controlled electrically and speed of piston of which are able to be controlled by means of a system controlled electrically and actuated hydraulically could be utilized as one of the most preferable countermeasures against those difficulties. Several units of rapid compression-expansion machines were developed but the speed up of frequency of piston movement still is the problem to be improved to cope with actual speed of internal combustion engines. Authors designed and manufactured a new rapid compression-expansion machine electrically controlled hydraulically actuated and computer programed and then examined the performance of one. Results of a set of experiments revealed acquirements of certain improvement of frequency of piston movement preserving the stability of system response and reproducing accurate compression ratio of cylinder those are the key function for the in-cylinder combustion experiments of internal combustion engines.

• Journal of Biosystems Engineering
• /
• v.39 no.1
• /
• pp.1-10
• /
• 2014

Purpose: This research was conducted to evaluate feasibility of a crank-type walking cultivators for weeding in furrowed upland. Methods: A walking cultivator developed by RDA was selected and evaluated with its working speed (S), cultivation depth (CD) and weeding performance (WP). The evaluation was performed in upland field on July and August, 2012. Also kinematic analysis of the machine was performed to draw out design improvements. Results: S in flat, uphill and downhill were about 0.11 m $s^{-1}$, 0.11 m $s^{-1}$, and 0.13 m $s^{-1}$ respectively. It was found that S had a low relevance with user conditions. The CD was 35 ~ 40 mm which was satisfied with the RDA guide for weeding machine. A wide variation was observed in values of WP depending on the growth stages of weeds and field conditions. The cultivator showed low performance in eliminating the well-grown weeds. Kinematic simulation revealed that high forward speed caused a high ratio of un-weeded area. Conclusions: The weeding performance of the cultivator was satisfactory for weeds in early growth stage but it showed difficulties in handling on up-slope and in entering up-land. Specifically, the weight of the cultivator was judged as overweight for female workers. The crank-hoe type cultivator was judged as unsuitable for small walking type machine due to weight of the four-bar linkage system. Kinematic analysis revealed that the ratio of crank speed to the ground speed must be 850 rpm s $m^{-1}$ (255 rpm based on 0.3 m $s^{-1}$) or greater to avoid uncultivated area. Selection of forward speed is a decisive factor in designing the weeding cultivator.

• Journal of the Semiconductor & Display Technology
• /
• v.23 no.2
• /
• pp.65-70
• /
• 2024

Using a computational fluid dynamics(CFD) simulation tool, we have provided a coating guideline for slot-die coating with a double layer slot die head. We have analyzed the fluid dynamics in terms of the coating speed, flow rate ratio, and viscosity ratio, which are critical for the stability of coating meniscus. We have identified the common coating defects such as break-up, air entrainment, and leakage by varying the coating speeds. The flow rate ratio is the critical parameter determining the wet film thickness of the top and bottom layers. It is shown that when the flow rate ratio exceeds or equals 1.8, air entrainment occurs due to insufficient hydraulic pressure in the bottom layer, even though the total flow rate remains constant. Furthermore, we have found that the flow of the bottom layer is significantly affected by the viscosity of top layer. The viscosity ratio of 4 or higher obstructs the flow of the bottom layer due to the increased hydraulic resistance, resulting in leakage. Finally, we have demonstrated that as the viscosity ratio increases from 0.1 to 10, the maximum coating speed rises from 0.4 mm/s to 1.6 mm/s, and the minimum wet film thickness decreases from 800 ㎛ to 200 ㎛.

• Journal of Biosystems Engineering
• /
• v.34 no.2
• /
• pp.71-76
• /
• 2009

This study was conducted to investigate the load acting on a tractor engine when it delivers the maximum power at drawbar. The results of the drawbar tests on the 5 locally-made and 14 imported tractors conducted at NIAE in 2004, and the 15 tractors tested at OECD test stations in foreign countries were analyzed and presented by the torque load ratio, defined as a ratio of the engine torque load caused by drawbar pull to its full-load capacity, as a function of pull speed. The NIAE test results showed that the torque load ratio increased from 20 to 80% with pull speed less than 5 km/h. At speeds faster than 5 km/h, it was 80${\sim}$110% regardless of the pull speed. However, the OECD test results showed that the torque load ratio was evaluated mostly to be 70${\sim}$90% in the entire pull speed range. The same trend was also shown for the maximum drawbar load. The difference in the torque load ratio may be attributable to bias-ply tires for locally-made and some imported tractors. It is also suggested that the input torque load may be increased safely up to 120% of the full load capacity of the tractor engine for an accelerated life test of tractor transmissions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.244-254
• /
• 2002

To enhance the acceleration performance and fuel consumption rate of a vehicle, the torque converter is modified or newly-developed with reliable analysis model. Up to recently, the one dimensional performance model has been used for the analysis and design of torque converter. The model is described with constant parameters based on the concept of mean flow path. When it is used in practice, some experiential correction factors are needed to minimize tole estimated error. These factors have poor physical meaning and cannot be applied confidently to the other specification of torque converter. In this study, the detail dynamic model of torque converter is presented to establish the physical meaning of correction factors. To verify the validity of model, performance test was carried out with various input speed and oil temperature. The effect of oil temperature on the performance is analysed, and it is applied to the dynamic model. And, to obtain the internal flow pattern of torque converter, CFD(Computational Fluid Dyanmics) analysis is carried out on three-dimensional turbulent flow. Correction factors are determined from the internal flow pattern, and their variation is presented with the speed ratio of torque converter. Finally, the sensitivity of correction factors to the speed ratio is studied for the case of changing capacity factor with maintaining torque ratio.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1998.06b
• /
• pp.206-216
• /
• 1998

The structural characteristics of small scale rice polisher was analyzed to improve its performance. Spraying characteristic of nozzles used for rice polishing was also analyzed by a machine vision system. The internal pressure of the polishing chamber was measured according to outlet resistance, water spraying , and roller shaft speed. In addition , the performance of the rice polisher was evaluated to improve it in the basis of internal pressure in polishing chamber, whiteness , and broken rice ratio of clean rice according to the operating conditions. Actual nozzle discharge rate and drop size were 125cc/min and 86.97㎛, respectively. In the case of water spraying on rices, the internal pressure showed 4.9-9.8N/㎠ increase, broken rice ration decreased , and there was no difference in whiteness . The internal pressure increased up to two time with the increase of the outlet resistance. Also, the pressure at the upper part of screen was one and half times as high as the pressure at the lower part. In the case of water spraying rate of 150 cc/min, the roller shaft speed of 850 rpm resulted in no difference in whiteness and decrease of 0.3%in broken rice ratio, comparing to the roller shaft speed of 950 rpm.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.6
• /
• pp.851-860
• /
• 2012

In this study, to evaluate the abatement of runoff pollution loads by the road sweeping(cleaning), various investigations are implemented at the sample area of the highway. As the results of evaluating the removal efficiency of pollutants along road cleaning, TSS showed about 78 % of the removal efficiency and COD showed 49 % of removal efficiency through the operation of cleaning vehicle of vacuum suction method. In case of TN and TP, they showed the relatively-lower removal efficiency by 30~35 %. TSS removal efficiency along the number of cleaning appeared about 60 % in case of one time of cleaning and the additional removal effect did not appear though the number of cleaning increased to two times. With running speed of cleaning vehicle, TSS removal ratio is lessened from 60 % to 20 % when cleaning vehicle speed up to 20 km/hr from 6 km/hr. It seems that the reasons why the removal efficiencies are inversely proportional to its speed are related to the lower vacuum efficiencies and the disturbed particles on the road. In the pollutant build-up analysis, it is showed that it takes more time to the critical pollutant build-up in the shoulder than the center of the road. It is also showed that the proper cleaning cycle is recommended as 4~6 dry weather days without rainfall events.