• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.71-77
• /
• 1999

In this study, Cu ferrite was machined with cermet tool to clarify the machinability. The main conclusions obtained were as follows. The tool wear becomes the smallest at the cutting speed of 90m/min with the depth of cut of 0.2mm. The surface roughness becomes larger with increasing the cutting speed and the chamfer angle. The tool with the chamfer angle of $15{\circ}$ shows the best performance. The surface roughness increases almost proportionally with the increase of the chip size. The tool wear decreases with increasing feed in the depth of cut not more than 0.2mm.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.3
• /
• pp.56-61
• /
• 2002

CuFe$_2$O$_4$ ferrite was machined with cermet tools to clarify the machinability. The tool wear became the smallest at the cutting speed of 90m/min with the depth of cut of 0.2mm. The surface roughness became larger with increasing the cutting speed and the chamfer angle of tool. The tool with the chamfer angle of 15° showed the smallest wear. The surface roughness increased almost proportionally with the increase of chip size. The tool wear reduced with increasing feed in the depth of cut not more than 0.2mm.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.11a
• /
• pp.123-134
• /
• 2000

In this study, adapted Turbo Coding Algorithm for reducing communication error of fire detection system for marine vessels, especially image transmission. and proposed decoding speed increasing method of Turbo Coding Algorithm. The results are as follows : 1) Confirmed that a Turbo Code is so useful methods for reducing communication error in lots of noise environments. 2) Proposed technology in this study of speed increasing method of Turbo Coding Algorithm proved 2 times speed up effect than normal Turbo Code and communication error reducing as well in the board made by VHDL software & chips of ALTER Company.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.238-243
• /
• 2000

The effect of the temperature, the fatigue and the test speed on DEN(double edged notch) specimen which was made by the pp-rubber composites during fracture was stuied. DEN specimen was made on PP-rubber composites through the injection molding. With increasing temperature the fracture strength is linearly decrease and the fracture energy is first increase by $0^{\circ}C$ and after that decrease. In the same temperature the fracture strength during increasing the notch radius is hardly increase. The fracture behaviour at low and high test speed is different entirely. At high test speed plastic region is small and fracture behaviour was seen to brittle fracture tendency. The deformation mechanism of polypropylene-rubber composites during fracture was studied by SEM fractography. A strong plastic deformation of the matrix material ahead of the notch/crack occured. The deformation seem to be enhanced by a thermal blunting of the notch/crack.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.84-87
• /
• 2002

The plunger speed of solenoid actuator is affected by mass of plunger magnetic motive force. inductance, and return spring. These factors are not independent but related with each other according to design characteristics of solenoid actuator So, it is impossible to change the designed value for the purpose of increasing plunger speed. In this paper, we performed the FEM analysis for non-magnetic ring which is used for increasing attraction force and plunger speed by concentration of effective magnetic flux, and also performed simulation for dynamic characteristics of plunger. And, we proved the propriety of these by experiments.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.3
• /
• pp.62-67
• /
• 2003

The grinding force generated during the grinding process causes an elastic deformation of the workpiece, grinding wheel, and machine system. Thus, the true depth of cut is always smaller than the apparent depth of cut. This is known as machining elasticity phenomenon. The machining elasticity parameter is defined as a ratio between the true depth of cut and the apparent depth of cut. It is an important factor to understand the material removal mechanism of the grinding process. To increase productivity, the value of this machining elasticity parameter must be large. Therefore, it is essential to know the characteristics of this parameter. The objective of this research is to study the effect of the major grinding conditions, such as table speed, depth of cut, on this parameter experimentally, Through this research, it is found that this parameter value is increasing when the table speed is decreasing or the depth of cut is increasing. Also, this parameter value depends on the grinding mode (up grinding, down grinding).

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.3
• /
• pp.512-518
• /
• 1996

Microcapsules containing 2, 4, 4'-trichloro-2-hydroxydiphenyl ether and perfumes were prepared by the coacervation using poly (vinyl alcohol) and crosslinking agents. Effects of dispersing agents, core materials, agitating speed and crosslinking agents on microcapsule size were investigated. The mean and deviation of microcapsule diameters decreased with increasing agitation speed. The diameters of m;crocapsules decreased with increasing dispering agent concentration at 6, 000 rpm of agitation speed, but it was not changed at 10, 000 rpm. The dispering effect of PVA is better than that of gum arabic. The slight increase in the diameter of microcapsule was observed when the amount of core material was increased. As the amount of crosslinking agent was increased, the diameter of microcapsule was decreased.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.10
• /
• pp.433-437
• /
• 2005

This paper studied Rotary type ultrasonic motor which has cross type stator. The stator consists of hollowed cross type metal which has four piezoelectric ceramics on the ends of cross bars. When two harmonic voltages which have 90$^{\circ}$ phase difference given to ceramics, the elliptical motion was generated in the inside tips. Inside tips are contact with rotor and these elliptical motions are rotate the rotor The finite element analysis was used to optimize the dimension and displacement of the stator. And the analyzed results were compared with the experimental results of the motor. As results, the speed and the torque of motor was increased by increasing width of the cross bar. And the speed and torque o( motor was not influenced to length of cross bar. The speed and torque was linearly increased by increasing voltage. The maximum torque was generated when the motor fabricated length of cross bar and width of ceramics in the ratio of 1:2.

• Journal of Powder Materials
• /
• v.7 no.3
• /
• pp.131-136
• /
• 2000

The effect of tempering temperature on the three point bending fatigue behavior of a P/M high speed steel JYPS-23 (1.28% C, 4.20% Cr, 6.40% W, 5.00% Mo, 3.10% V, bal. Fe) was investigated. The number of cycles to failure of the specimen austenitized at $1175^{\circ}C$ drastically increased with increasing tempering temperature. As tempering temperature increased from 500 to $620^{\circ}C$, the volume fraction and average size of carbides (MC or M6C) did not significantly changed, while hardness decreased drastically. The reduced hardness is due to the softening of matrix, which increased the resistance of the fatigue crack propagation. For a practical application, powder compacting test were also conducted with the P/M high speed steel punches tempered at 500, 580, and $620^{\circ}C$. The number of compacting cycles to failure of the punches also increased with increasing tempering temperature.

• Geomechanics and Engineering
• /
• v.21 no.3
• /
• pp.237-245
• /
• 2020

The process of evaporation from free water surface was simulated in a large scale environmental chamber under various controlled atmospheric conditions and also was modelled by a new mass transfer model. Six evaporation tests were conducted with increasing wind speed and air temperature in the environmental chamber, and hence the effect of atmosphere parameters on the evaporation process and the corresponding response of water were investigated. Furthermore, based on the experiment results, seven general types of mass transfer models were evaluated firstly, and then a new model consisted of wind speed function and air relative humidity function was proposed and validated. The results show that the free water evaporation is mainly affected by the atmospheric parameters and the evaporation rate increases with the increasing air temperature and wind speed. Both the air and soil temperatures are affected by the energy transformation during water evaporation. The new model can satisfactorily describe the evaporation process from free water surface under different atmospheric conditions.