• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.200-204
• /
• 2002

When the vector control, which does not need a speed? signal from a mechanical speed sensor, it is possible to reduce the cost of the control equipment and to improve the control performance in many industrial application. This paper describes a rotor speed identification method of induction motor based on the theory of flux model reference adaptive system. The estimator execute the rotor speed identification so that the vector control of the induction motor may be achieved. The improved auxiliary variable of the two model are introduced to perform accurate rotor speed estimation. Simulation result show the validity of the proposed control method.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2008-2011
• /
• 1998

When the vector control, which does not need a speed signal from a mechanical speed sensor, it is possible to reduce the cost of the control equipment and to improve the control performance in many industrial application. This paper describes a rotor speed identification method of induction motor based on the theory of Model Reference Adaptive System(MRAS). The identifier execute the rotor speed identification so that the vector control of the induc-tion motor may be achieved. The improved auxiliary variable are introduce to perform accurate rotor speed identification. Simulation and experimental result show the validity of the proposed control method.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.3133-3141
• /
• 2011

The next generation domestic high speed railway system is a power distributed type and uses vector control method for motor speed control. Nowadays, inverter driven induction motor system is widely used. However, recently PMSM drives are deeply considered as a alternative candidate instead of an induction motor drive system due to their advantages in efficiency, noise reduction and maintenance. The next-generation high speed train is composed of 2 converter units, 4 inverter units, and 4 Traction Motor units. Each motor is connected to the inverter directly. In this paper, the effect of IPMSM parameter variations to the system operation characteristics of the multi inverter drive high speed train system are investigated. The parallel connected inverter input-output characteristics are analyzed to the parameter mismatches of IPMSM using the 1C1M control simulator based on Matlab/Simulink.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.393-397
• /
• 2005

Since the braking system of rolling stock is directly linked to it's safety, ensuring reliability of braking system and evaluation of performance of it are very important. To develope the performance of braking system, it is required advanced technology and gradually various factors in the field test result. This study is designed to analyze the air pressure control about braking force in rolling stock, also, by comparing braking force of high speed railway with that of high speed train. This paper suggests to establish a method of computation of braking force form the air pressure control. And The high speed train researches into patterns of braking system such as the train of speed up and introduction of electric and pneumatic braking system.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1685-1690
• /
• 2010

This paper describes the calculation and application of the speed profile for the train speed control when the train is operated by ATO(Automatic Train Operation). We propose a speed profile calculation method considering the speed limitation and the jerk limitation, in order to maintain the quality of the train automatic operation. In previous works, ATO calculates a desired speed profile along the time, and controls the train to follow the profile. In this case, it may be hard to follow the restrictive speed along the location or to stop the train with a low location error, because of the difference between the desired location at each time and the real location of the train due to the control error. In the proposed method in this paper, we calculate a desired speed profile along the time considering the speed and jerk limitation first, and derive a speed profile along the location using it. If the restrictive speed profile is changed or the train speed strayed from the speed profile, ATO system calculates new speed profile and applies it immediately. Because ATO system controls the train speed based on the train location, the accuracy of the train location control can be improved. A simulation system for the test of the automatic train operation using this method is designed.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.6
• /
• pp.635-644
• /
• 2016

Train speed control is a vital part of train protection to build safe movement at an operation track. There is a special condition of track that needs more attention to protect the train, for example in slope area. Moreover, in developing country with vandalism problem, it requires to install minimalized equipment on the trackside. In addition, in tropical country, on tracksides it will be potentially pooling water that influences to the performance of trackside equipment. To address these problems, we propose the train speed control for slope area using infrared system. By installing on the pole configuration, the system offers a less challenging, economically sensible, minimalized installation of equipment on the trackside and reliability for heavy rain environment. This paper concentrates on the controlling train speed and measurement performance evaluation in slope area. The proposed train speed control system can monitor and control the speed in sloping area with maximum 3.6% and controlled speed about 20 km per h.

• Journal of the Korean Society for Railway
• /
• v.5 no.4
• /
• pp.267-275
• /
• 2002

The traction drive system for the urban transit maglev system is described in this paper. To control the magnitude and frequency of the output voltage of induction motor transiently, the vector control strategy is generally used. But in case of the traction drive system for the railway vehicle, it is difficult to use the vector control caused by the one-pulse mode in the high speed region. Therefore, this paper proposes the control strategy combined the vector control in the low speed region and the slip frequency control in the high speed region. And also, the overmodulation PWM method is discussed to make the change to the one-pulse mode softly. The performance of the proposed traction drive system is verified by the MATLAB simulation results.

• Wind and Structures
• /
• v.21 no.4
• /
• pp.443-460
• /
• 2015

In this paper, an integrator based method to estimate the effective wind speed in wind turbine systems is proposed. First, the aerodynamic torque was accurately estimated through a proportional gain based observer where the generator speed is the measured output of the system. The torque signal contains not only useful frequencies of the wind, but also high frequencies and the ones due to structural vibration. The useful information of the wind signal is low frequency. A spectral analysis permitted the determination of the useful frequencies. The high frequencies were then filtered before introducing the torque signal in the wind speed observer. The desired effective wind speed was extracted through an integrator based observer using the previously estimated aerodynamic torque. The strength of the method is to avoid numerical solutions used in literature of the wind speed estimation. The effectiveness of the proposed wind speed estimator and its use to control the generator speed has been tested under turbulent situations using the FAST software (Fatigue, Aerodynamics, Structures, and Turbulence), for large scale Megawatt turbine.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.4
• /
• pp.57-64
• /
• 2007

In the recent years, development of machine tool with high speed feeding system have brought a rapid increase in productivity. Practically, thermal deformation problem due to high speed is, however, become a large obstacle to realize high precision machining. In this study, therefore, the construction of automatic error compensation system to control thermal deformation in high speed feeding system with real time is proposed. To attain this purpose, high speed feeding system with feeding speed 60mm/min is developed and experimental equation for relationship between thermal deformation and temperature of ball screw shaft using multiple regression analysis is established. Furthermore, in order to analyze thermal deformation error, compensation coefficient is determined and thermal deformation experiments is carried out. From obtained results, it is confirmed that automatic error compensation system constructed in this study is able to control thermal deformation error within $15{\sim}20{\mu}m$.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.199-203
• /
• 2011

With the improvement of standard of manufacturing process, oil cooling unit for manufacturing machine has been developed. A control system must be designed in order to keep oil temperature of the machine within a very restricted range and also to reduce energy consumption. In order to get the low deviation of the controlled temperature and the low efficiency, the on/off control scheme is gradually being replaced by a variable speed refrigeration system (VSRS) with an inverter driven compressor over recent decades. This paper gives the flowchart to control the compressor speed and also the electronic expansion valve (EEV) aperture in oil cooling unit refrigeration system using R22 as the refrigerant. This control scheme has already tested in experiment apparatus with room temperature condition constant at $25^{\circ}C$ and variable load condition at 4kW, 6kW, 7kW, 8kW and 10kW.