• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1471-1477
• /
• 2014

This paper addresses the development on supply-demand outlook model of Jeju winter radish and introduces a projection of supply-demand and market prices during 2014-2018 using the model. The supply-demand outlook model is specified as a partial equilibrium model of Jeju winter radish. Each equation in the model is estimated by using the econometric techniques. A review of the model stability is also carried out by the references based on RMSPE, MAPE, and Theil's inequality coefficients. According to the reference of RMAPE, the error rates of the forecasting values of the cultivation ares, production quantity, and consumption quantity show less than 4% and the error rate of market price is below 10%. The cultivation area and production quantity are projected respectively to be increased to 6,650ha and 433,310MT in 2018.

• Journal of Energy Engineering
• /
• v.13 no.2
• /
• pp.128-132
• /
• 2004

This paper presents a new methodology to get pareto-optimal solution for generation planning. First, we apply dynamic programming, and we can get an optimal economic dispatch considering total quantity of contamination for the specified term. Second, we developed a method which can get pareto-optimal solution. This solution is consisted of a set of optimal generation planning. As a result, decision maker can get pareto-optimal solutions, and can choose a solution. We applied this method to the test system, and showed the usefulness.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.280-283
• /
• 1995

In centrifugal barrel finishing, it is easy to establish the optimum working conditions for different workpieces. As they are adjusted in trial and error practically, production efficiency and quality are some- times low In the present paper, firstly, installation of the barrel finishing machine, finishing purpose and working conditions have been analyzed in order to eliminate the defects of the finished surface. Secondly, on the basis of this result, quantity of the water and selection of the media and the compound, etc. have been investigated. As a result, production efficiency and quality have been improved under the specified optimum working conditions. In addition, durability of the media and the compound has been tested experimentally. As a result, it was found that the expected life of the media is about 85 hrs and that of the compound is about 5 hrs. Besides high quality control has been achieved by newly proposed inspection at regular intervals.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.35-39
• /
• 2000

The piercing and blanking of thin sheet metal working is specified division in press die design and making. In order to prevent the detects, the optimum design of the production part, strip process layout, die design, die making and try out etc. are necessary the analysis of effective factors. For example, theory and practice of metal shearing process and its phenomena, die structure, machine tool working for die making, die materials and its heat treatment, metal working in industrial and its know how etc. In this study, we analyzed whole of data base, theoretical back ground of metal working process, and then performed the progressive die tryout with the screw press. This study regards to the aim of small quantity of production parts press working. Part 1 of this study reveals with production part and strip process layout design.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.224-228
• /
• 2000

The piercing and blanking of thin sheet metal working is specified division in press die design and making. In order to prevent the detects, the optimum design of the production part, strip process layout, die design, die making and try out etc. re necessary the analysis of effective factors. For example, theory and practice of metal shearing process and its phenomena, die structure, machine tool working for die making, die materials and its heat treatment, metal working in industrial and its know how etc. In this study, we analyzed whole of data base, theoretical back ground of metal working process, and then performed the progressive die tryout with the screw press. This study regards to the aim of small quantity of production part's press working. Part 1 of this study reveals with production part and strip process layout design.

• International Commerce and Information Review
• /
• v.7 no.1
• /
• pp.283-307
• /
• 2005

The research was carried out at the electronic Gw-mart located at Gangwon province. The secondary data and the various other reference materials were used for the research. This research brings forth the concrete activation plan for the activation of an electronic market in the Gangwon province. So, the activation plan for an e-market at Gang won can be done in six ways, first result of the undertaken research achieved in six ways- first, concentration has to be laid on the internet portal sites, second, the local sites should be well connected with the shopping mall facilities, third, a trustworthy shopping mall has to be established by maintains the product quality and quantity, fourth, a visible distinction should be made between the various products, fifth, the division of labor must be specified and a provisions should be made for a efficient after service.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.9
• /
• pp.934-943
• /
• 1990

There are no turn-on losses in the series Resonant Converter which operates above the resonance frequency, and the commutation stress on the switched component is low. For a given Series Resonant Converter with specified load resistance, the output voltage is a function of the operation frequency. This paper describes the static and dynamic characteristic analysis of the Series Resonant DC to DC Converter, which is operating above the resonant frequency, with frequency control. For the analysis method, state plane technique is adopted, and the circuit operation is defined from normalized switching frequency, Fsn. Under this condition, circuit performance is analyzed ideally. The validity of the proposed analysis is verified by comparing with experimental results, the stability of the converter is confirmed against small variations around the operating point by conventional frequency domain analysis, and the stress quantity added to switch component is shown.

• Journal of Digital Convergence
• /
• v.10 no.11
• /
• pp.383-387
• /
• 2012

Development of automated document management system specified for scanned invoice images suffers from rigorous accuracy requirements for extraction of monetary data, which necessiate automatic validation on the extracted values for a generative invoice table model. Use of certain internal constraints such as "amount = unit price times quantity" is typical implementation. In this paper, we propose a noble invoice information extraction model with improved auto-validation method by utilizing table header detection and column classification.

• Korean Journal of Computational Design and Engineering
• /
• v.19 no.4
• /
• pp.402-409
• /
• 2014

Presented in this paper is a scheduling method for semiconductor backend process considering the backward pegging. It is known that the pegging for frontend is a process of labeling WIP lots for target order which is specified by due date, quantity, and product specifications including customer information. As a result, it gives the release plan to meet the out target considering current WIP. However, the semiconductor backend process includes the multichip package and test operation for the product bin portion. Therefore, backward pegging method for frontend can't give the release plan for backend process in semiconductor. In this paper, we suggest backward pegging method considering the characteristics of multichip package and test operation in backend process. And we describe the backward pegging problem using the examples.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.793-808
• /
• 2009

This paper presents procedure and prediction method of internal and external stabilities when designing D.C.M, with main factors to be considered, such as chemical reaction of additive, physical properties of stabilized body and mixing strength. Results show that through case studies, a design unconfined compressive strength of stabilized body (hereafter referred to as 'compressive strength') directly depends on the quantity of cement, which is decided by laboratory test, and the compressive strength enormously affects internal and external stabilities. So laboratory mixing test to obtain the compressive strength for design allowable stress should be given careful considerations.