• 대한기계학회논문집B
• /
• 제25권9호
• /
• pp.1193-1200
• /
• 2001

There are many regulation test methods to be related with engine emissions such as CVS-75, D-13, ECE-15 modes and so on. Most of these modes are consisted of lots of transient conditions that have rapid acceleration, deceleration and cranking modes. In this experimental research, the engine characteristics of cranking, accelerating and power output in a S.I. engine were studied to compare with neat gasoline and alternative fuels of M30 (methanol 30%, aromatic series 32%, non-aromatic 38%) and M50 (methanol 50%, aromatic 30%, non-aromatic 20%) for performance and exhaust emissions. The results show that reformulated methanol fuels are better emissions reduction of 15.7% over than that of neat gasoline fuel especially in HC and CO emissions at cranking mode. And the accelerating performances coincide with the results of distillation curve. CO concentration for M50 fuel is varied in a just little for the condition of slow acceleration. At wide-open throttle condition, brake specific energy consumption of reformulated fuels is increased and thermal efficiency is some what lower than that of gasoline fuel.

• 한국통신학회논문지
• /
• 제42권5호
• /
• pp.1058-1068
• /
• 2017

V2X 통신에서, 사이드링크 수신 능력들이 없는 디바이스들 지원하기 위한 경우 및 단말의 파워 소비 감소가 요구되는 경우를 고려하여 랜덤 기반의 자원 선택 방식이 요구된다. 본 논문에서는 PSCCH 주기 내에서의 데이터를 위한 서브프레임 풀에 대하여 하나의 TRP를 반복 적용하는 D2D에서의 자원 선택 방식을 개선하여, 보다 향상된 랜덤 자원 선택 방식을 위해 단말-특정한 시드 값을 가지는 의사-랜덤 시퀀스를 바탕으로 TRP가 매 적용마다 달리 적용되는 방식을 제안하였다. 수치 분석을 통해 제안된 기술의 성능을 분석한 결과, 데이터 TB을 위해 각 단말에게 할당된 자원들 간의 충돌 확률이 줄어들며 이를 통해 자원 출동을 최대한 피하면서 동시에 자원할당이 가능한 단말의 개수를 늘릴 수 있는 것을 확인할 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제17권5호
• /
• pp.552-559
• /
• 2004

In recent, there have been several developments in lamp technology that promise savings in electrical power consumption and improved quality of the lighting space. Above all, the advantage of ring-shaped electrodeless fluorescent lamp is the removal of internal electrodes and heating filaments that are a light-limiting factor of conventional fluorescent lamps. The ring-shaped electrodeless lamp is intended as a high efficiency replacement for the incandescent reflector lamp in many applications. Therefore, the life time of ring-shaped electrodeless fluorescent lamps is substantially higher than that of conventional fluorescent lamps and last up to 60,000 hours. In this paper, maxwell 3D finite element analysis program(Ansoft) was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 250 KHz and some specific conditions. The optical characteristics were measured luminance and a temperature and an optical spectrum distribution for 10 min in a one minute interval at the same time. With a goal of finding alternative materials, we show measurement results of electrical characteristics of a ring-shaped electrodeless fluorescent lamp as a function of frequency and the number of coil turns using a highly permeable($\mu$$_{r}$(equation omitted) 2,000) Mn-Zn ferrite. These results are compared with those of conventional ring-shaped electrodeless fluorescent lamp. It is found that the resistance, inductance and impedance are increased while the quality factor decreases as frequency increases.s.

• 한국유체기계학회 논문집
• /
• 제17권2호
• /
• pp.24-29
• /
• 2014

In general, a large-capacity axial flow fan is used for industrial processes or ventilation in a social overhead capital infrastructure. The main characteristics of the large axial-flow fan need a lot of electrical power consumption and operate 24 hours a day, 365 days a year. Since the large axial flow fan consumes several hundreds to thousands kW per hour, both manufacturer and consumer are struggling to select high efficiency products for saving energy and reducing operation cost. Therefore, the performance testing should be accurately conducted in experimental equipments. The performance estimation and uncertainty of measurement of the axial-flow fan gathered from the result from nozzle shaped testing equipments certified with ANSI/AMCA standard and duct shaped testing equipment under the same experimental condition. The experimental results from both facilities have maximum 17% differences in performance evaluation and uncertainty of measurement. As considering that the differences, it is doubt about the reliability of testing result. The test was repeated with the specific term during 12 months because it is important to fully reflect the real conditions and to decide the repeatability of data. The evaluation of duct type testing facilities was failed to get an uncertainty measure. Testing results were previously published. As a series of previous paper, axial fan (∅1690 mm) and duct type testing facilities were fabricated. The purpose of fabricating testing equipment was testing an uncertainty measurement under the controlled environments.

• 상하수도학회지
• /
• 제29권1호
• /
• pp.89-96
• /
• 2015

Smart water grid is a water network with communication to save water and energy using various water resources. In smart water grid, water product from the various sources can be blended to be supplied to end-users. The product water blending was reported by literatures while feed water blending has been rarely reported so far. In this work, a commercial reverse osmosis (RO) system design software provided by a membrane manufacturer was used to elucidate the effect of feed water blending on the performance of seawater reverse osmosis (SWRO) plant. Fresh water from exisiting water resource was assumed to be blended to seawater to decrease salt concentration of the RO feed water. The feed water blending can simplify the RO system from double to single pass and decrease seawater intake amount, the unit prices of the RO system components including high pressure pump, and operation risk. Due to the increase in RO plant capacity with the feed water blending, however, the RO membrane area and total power consumption increase at higher water blending rates. Therefore, a specific benefit-cost analysis should be carried out to apply the feed water blending to SWRO plants.

• 센서학회지
• /
• 제8권4호
• /
• pp.327-332
• /
• 1999

비표면적이 약 $200\;m^2/g$인 ${\gamma}-Al_2O_3$를 합성하여 얻은 ${\gamma}-Al_2O_3$ 담체에 Pd, Pt와 같은 귀금속 촉매를 첨가하여 접촉연소식 가스감지소자를 제작하였다. 제작된 센서는 최적동작을 위한 인가전압 1.75 V에서 소모전력은 약 500 mV였고, 부탄, 메탄 및 프로판 각각 100 %LEL에 대해서 약 120 mV의 높은 감도 특성을 보였다. 제작된 센서는 탄화수소 가스 농도에 대한 선형성, 재현성, 그리고 상대 습도변화에 대해서 안정된 감도 특성을 보여 주었다. 그리고 약 100일 동안 부탄 가스에 대해서 안정된 센서 감도 특성을 보여 주었다.

• 한국지열·수열에너지학회논문집
• /
• 제11권4호
• /
• pp.1-6
• /
• 2015

In this study, energy performance of two types of food dryers which are electric heater and heat pump is studied experimentally. With drying chamber temperatures controlled at 45, 50 and $55^{\circ}C$, sliced radish is dried from an initial mass of 90 to final 7 kg. Moisture content, drying time, total power consumption, MER (moisture extraction rate, kg/h) and SMER (specific moisture extraction rate, kg/kWh) are measured and analyzed. As the drying chamber temperature is increased, drying time is shortened but energy efficiency is reduced for both types. For an electric heater dryer, the effect of chamber temperature on drying time is significant but less significant on energy efficiency. For a heat pump dryer, the dependence of chamber temperature on drying time is weak but strong on energy efficiency. Temperature levels have little effect on electric heater dryer performance but strong effect on heat pump dryer which operates on a vapor compression refrigeration cycle. The energy performance of the heat pump dryer is superior with an average SMER of 2.175 kg/kWh which is 2.22 times greater than that of the electric heater dryer with SMER of 1.224 kg/kWh.

• 한국유체기계학회 논문집
• /
• 제20권1호
• /
• pp.53-58
• /
• 2017

This paper describes liquidity evaluation on the horizontal branch pipe connected to a food waste disposer and performance of five disposers marketed. Experimental apparatus for analyzing the five disposers has been introduced to measure vibration, sound level and power consumption of the disposers. Simulator for analyzing the required water velocity to avoid waste jam inside the pipe connected to a food waste disposer has been designed and constructed. The simulator can control some experimental parameters: pipe slope, disposer supply water quantity, food waste materials and operation time of a disposer. Throughout the experimental measurements of the disposers marketed, it is found that the time need to crash food waste is about 20 seconds on the average. At the same flow condition, increase rate of internal water velocity is accelerated as the pipe slope increases. The water velocity inside the pipe having 50 A and slope of 1/50 is 0.26 m/s when the water flowrate to supply the disposer is 16 l pm. Considering the specific gravity and adhesion property of food waste, water velocity of the horizontal branch pipe connected to a food waste disposer need to excess 0.26 m/s at least to avoid the waste blockage inside the pipe.

• Asia Pacific Journal of Business Review
• /
• 제4권2호
• /
• pp.1-21
• /
• 2020

The purpose of this research is to investigate young consumer motivation in regards to shopping mall. Young adults are an emerging age group that has economic autonomy and power of making independent decisions. In addition, this young segment providing an interesting challenges and opportunities for marketing professionals. Therefore, it is pertinent to analyse their shopping motivations, so that the marketers can understand and influence the consumption behaviour of this specific group. A survey using self-administered questionnaire was conducted to assess the mall-directed shopping habits and shopping orientations. A total of 164 usable surveys were obtained. In addition of exploratory factor analysis, confirmatory factor analysis and structural equation modeling was applied to prove the hypotheses. We have found that young Australian shoppers were motivated to visit malls primarily by the role enactment and exploration dimensions. They were the strongest motivators which explaining why young Australian consumers patronize malls. Young consumers of Australia enjoyed the mall environment, exploring new things, socializing with friends, comparing prices and the variety of products and services offered. The results of our study have several implications that should be of benefit to the retailing industry and mall management. Developers of malls must develop their mall more than simply a place for buying products. As such, mall management should make sure that their mall atmospherics offer a mall environment that is pleasing to multiple senses, to ensure it is conducive for shoppers to stay and spend more of their time and money. Mall management must execute strategies to maintain their attraction to younger consumers, perhaps by including stores that are futuristic and offer the most advanced styles or technologies, and appeal to somewhat older adults by offering the tenant, entertainment, and experience mix they will prefer. It is recommended that future research utilize random sampling methods to ensure the generalizability of results.

• 터널과지하공간
• /
• 제26권3호
• /
• pp.143-153
• /
• 2016

본 연구에서는 블루투스 비콘 기술의 광업 및 건설 분야 활용을 위해 기술의 특징과 다양한 활용사례를 조사하고, 분석하였다. 문헌 조사를 통해 블루투스 기술의 개념과 버전별 특징을 정리하였고, 블루투스 비콘 기반 서비스의 대표적인 유형과 타 분야에서의 실제 활용사례를 분석하였다. 광업 분야에서는 구버전인 블루투스 클래식 기술을 활용한 기존의 연구사례는 있으나 블루투스 비콘 기술을 활용한 사례는 발견할 수 없었다. 건설 분야에서는 최근에 블루투스 비콘 기술을 활용하여 현장의 원자재 운반 작업을 개선한 사례를 발견할 수 있었다. 블루투스 비콘 기술은 전력 소비량이 작고 스마트폰과 연동이 용이한 장점이 있으므로 기술 개발을 통해 광업 및 건설 분야에 도입할 경우 현장의 생산성과 안전성 개선을 위해 유용하게 활용할 수 있을 것이라 판단된다.