• Journal of Electrochemical Science and Technology
• /
• v.11 no.4
• /
• pp.406-410
• /
• 2020

Despite a simple preparation of manganese oxide (MnO₂) nanowires by electrodeposition, the improvement in specific capacitance (C_sp) and voltammetric response of the MnO₂ nanowire-based electrodes has been quite limited. This is attributed to the poor electrical conductivity of MnO₂ and its dense bulk morphology due to the aggregation of the nanowires. This study investigated the capacitive performance of MnO₂ nanowires electrodeposited on agarose thin films. The good ionic conductivity and porous network of the agarose film provided favorable growth conditions for the MnO₂ nanowires with suppressed aggregation. A maximum C_sp value of 686 F/g measured at a scan rate of 10 mV/s was obtained, which was significantly larger than that of 314 F/g for the agarose-free MnO₂ electrode at the same scan rate. The rate capability was also improved. The C_sp measured at a high scan rate of 100 mV/s retained 74.0% of the value measured at 10 mV/s, superior to the retention of 71.1% for the agarose-free MnO₂ electrode.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.3
• /
• pp.343-353
• /
• 1997

This paper presents a theoretical model for predicting transient behaviors during storage process of the cool storage system using the R141b clathrate. Introduction of the lumped capacitance method along with a brine reservoir having large thermal capacity yields a set of simplified energy equations. Based on the Arrhenius equation and the known experimental findings, the formation rate of clathrate for which the degree of subcooling is properly accounted is newly developed. An effective nondimensionalization of the model equations facilitates the closure of modeling as well as parametric study. Calculated results for a specific case not only simulate a typical pattern of temperautre variation in the tank successfully, but also agree reasonably well with available data. The effect of each characteristic parameter on the system performance is also investigated. It is revealed that the dominant among relevant parameters are the activation energy of reaction, the degree of subcoling and the initial mass fraction of refrigerant. Finally, the uncertainty associated with modeling of the shaft work variation appears to need further studies.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.61-67
• /
• 2004

The structural, electrical properties of the electrolytic capacitors were examined. By the addition of additives to hydrochloric acid solution increased the dielectric aluminum surface layer. For etch tunnels formed in hydrochloric acid, the away and density of the tunnels was not uniform, while for those formed in hydrochloric acid with additives the distribution presented relative uniformity. When the etched surface formed in hydrochloric acid with $5\%$ ethylene glycol, the enlargement of specific surface area was more effective.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.393-396
• /
• 2008

Propellant consumption control for space launch vehicle can be achieved by propellant utilization system (PUS) and tank depletion system (TDS). In the course of developing new space launch vehicles, the main target of design is on reducing of space launch vehicle weight, which results in increasing both specific impulse and payload weight. The weights of space launch vehicles are generally allocated to structure, propulsion system, and propellants loaded. The quantity of propellants filled in propellant tanks may be estimated with the propellants actually consumed by propulsion system to complete its mission and the propellants left on-board at the time of engine shut-off. To minimize the remaining quantity of propellants on-board the supplying propellants' O/F ratio should be controlled from the certain time before engine shutdown. To control an O/F ratio, a control system, which accurately measures and compares the remainder of propellants in tanks and pipes, should be needed. This paper solely dedicates its contents to explore the merits and demerits of various level sensor, which is one of the important elements for PUS and TDS, and the transmission and control of signals within space launch vehicle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1079-1084
• /
• 2004

This work describes the effect of electrode binder on the characteristics of electric double layer capacitor. Among carboxymethylcellulose (CMC), Polyvinylpyrrolidone (PVP), Polyvinyl Alcohol (PVA), and Polyvinylidene Fluoride (PVDF), the unit cell using CMC showed good rate capability at current densities between 2.5 mA/$\textrm{cm}^2$～100 mA/$\textrm{cm}^2$. However, CMC as a binder is incongruent, because the electrode bound with CMC is rigid and easy to crack during a press and winding process for fabrication of capacitor. The unit cell capacitor using the electrode bound with binary binder composed of CMC and Polytetrafluoroethylene (PTFE), especially in composition CMC : PTFE =60 : 40 wt.%, has exhibited the better mechanical properties than those of the unit cell with CMC. On the other hand, the mechanical properties of CMC+PTFE electrode, coated on underlayer composed of CMC and carbon black, were much improved.

• Applied Microscopy
• /
• v.47 no.2
• /
• pp.77-83
• /
• 2017

Drastic development of ubiquitous devices requires more advanced batteries with high specific capacitance and high rate capability. Large-area microstructure characterization across the stacks of cathode, electrolyte and anode might reveal the origin of the instability or degradation of batteries upon cycling charge. In this study, sample preparation methods to observe the cross-section view of the electrodes for battery in SEM and several imaging tips are reviewed. For an accurate evaluation of the microstructure, ion milling which flats the surface uniformly is recommended. Pros and cons of cross-section polishing (CP) with Ar ion and focused ion beam (FIB) with Ga ion were compared. Additionally, a modified but new cross-section milling technique utilizing precision ion polishing system (PIPS) which can be an alternative method of CP is developed. This simple approach will make the researchers have more chances to prepare decent large-area cross-section electrode for batteries.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.9
• /
• pp.849-854
• /
• 2006

In this study, the hybrid electrodes, composed of the activated carbon powders and $LiCoO_{2}$ powders, were prepared as a cathode for the high-capacitance type hybrid capacitor, and the electrochemical properties of the hybrid electrodes were examined in terms of the weight composition and the milling time of $LiCoO_{2}$ powders. The specific volumetric capacities were increased with increasing of the composition of $LiCoO_{2}$ powders in the hybrid electrodes. On the other hand the coin cell capacitors, using the hybrid electrodes with $LiCoO_{2}$ poweders milled for 200 h, have exhibited the lower internal resistivities and the better capacity retention after 100 charge-discharge cycle than those of the coin cell capacitors using the hybrid electrodes with raw $LiCoO_{2}$ powders.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1417-1419
• /
• 1997

In this paper, the dielectric properties is made researches by the dose of electron beam in order to investigate the electrical properties for transformer oils due to electron beam irradiation. To measure the dielectric loss of irradiated specimen, the liquid electrode of coaxial cylindrical shape is used, and its geometric capacitance is 16 [pF]. And the dielectric dissipation factor, $tan{\delta}$, is measured by using the Video Bridge 2150. The thermal static oven with an automatic temperature controller is used so as to apply specific temperature to specimen. This experiments for measuring the dielectric loss is performed at $20{\sim}120[^{\circ}C]$ in temperature range, $30{\sim}1.5{\times}10^5[Hz]$ in frequency and $300{\sim}500[mV]$ in voltage.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.296-296
• /
• 2013

Supercapacitor is a capacitor with extraordinarily high energy density, which basically consists of current collector, active material and electrolyte. Ruthenium oxide ($RuO_2$) is one of the most widely studied active materials due to its high specific capacitance and good electrical conductivity. In general, it is known that the coating of $RuO_2$ on nanoarchitectured current collector shows improved performance of energy storage device compared to the coating on the planar current collector. Especially, the surface structure with standing coaxial nanopillars are most desirable since it can provide direct paths for efficient charge transport along the axial paths of each nanopillars and the inter-nanopillar spacing allows easy access of electrolyte ions. However, well-known fabrication methods for metal or metal oxide nanopillars, such as the process using anodize aluminum oxide (AAO) templates, often require long and complicated nanoprocess.In this work, we developed relatively simple method fabricating indium tin oxide (ITO) nanopillars via sputtering. We also electrodeposited $RuO_2$ nanoparticles onto these ITO nanopillars and investigated its physical and electrochemical properties.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.295-295
• /
• 2013

Supercapacitors with higher energy and power density are attracting growing attention for their wide range of potential applications such as portable electronic equipments, hybrid vehicle and cellular devices. In various classes of materials for supercapacitors, the redox pseudocapacitive materials such as conducting polymers and metal oxides have been most widely studied recently. The nanostructuring of the electrode surface has also been focused on since it can provide large surface area and consequently easy diffusion of ions in the capacitors. Among the active materials, in this work, we have used polyaniline (PANi) and manganese oxide ($MnO_2$). PANi is one of the promising electrode and active materials due to its desirable properties such as high electrochemical activity, high doping level and stability. $MnO_2$ is also widely studied material for supercapacitors since it is relatively cheap and environmentally friendly. In this work, we fabricated PANi hollow nanospheres by polymerizing aniline monomers on the polystyrene (PS) nanospheres and then dissolving the inner PS spheres. This nanostructuring of the PANi surface can provide large surface area and hence easy diffusion of electrolyte ions. We also incorporated $MnO_2$ nanoparticles into the PANi hollow nanospheres and investigated its electrochemical properties. It is expected that the combination of these two active materials with slightly different working potential windows show synergetic effects such as broader working potential range and enhanced specific capacitance.