• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.9
• /
• pp.513-520
• /
• 2016

It is well known that volatile compounds including disinfection by-products as well as emissive dissolved gas in water can be removed effectively by air stripping. The micro-bubbles of flotation unit are so tiny as microns while the diameter of fine bubbles applied to air stripping is ranged from hundreds to thousands of micrometer. Therefore, the micro-bubbles in flotation can supply very wide specific surface area to transfer volatile matters through gas-liquid boundary. In addition, long emission time also can be gained to emit the volatile compound owing to the slow rise velocity of micro-bubbles in the flotation tank. There was a significant difference of the THMs species removal efficiency between air stripping and flotation experiments in this study. Moreover, the results of comparative experiments on the removal characteristics of THMs between air stripping and flotation revealed that the mass transfer coefficient, $K_La$ showed obvious differences. To overcome the limit of low removal efficiency of dissolved volatile compounds such as THMs in flotation process, the operation range of bubble volume concentration is required to higher than the operation condition of conventional particle separation.

• The KIPS Transactions:PartA
• /
• v.16A no.6
• /
• pp.419-426
• /
• 2009

To realistically simulate fluid, the Navier-Stokes equations are generally used. Solving these Navier-Stokes equations on the Eulerian framework, the non-linear advection terms invoke heavy computation and thus Semi-Lagrangian methods are used as an approximated way of solving them. In the Semi-Lagrangian methods, the locations of advection sources are traced and the physical values at the traced locations are interpolated. In the case of Stam's method, there are relatively many chances of numerical losses, and thus there have been efforts to correct these numerical errors. In most cases, they have focused on the numerical interpolation processes, even simultaneously using particle-based methods. In this paper, we propose a new approach to reduce the numerical losses, through improving the tracing method during the advection calculations, without any modifications on the Eulerian framework itself. In our method, we trace the grids with the velocities which will let themselves to be moved to the current target position, differently from the previous approaches, where velocities of the current target positions are used. From the intuitive point of view, we adopted the simple physical observation: the physical quantities at a specific position will be moved to the new location due to the current velocity. Our method shows reasonable reduction on the numerical losses during the smoke simulations, finally to achieve real-time processing even with enhanced realities.

• Korean Journal of Ecology and Environment
• /
• v.47 no.4
• /
• pp.328-336
• /
• 2014

Nakdan weir, which is located in the second weir among the 8 weirs of Nakdong River, had been constructed from Nov. 2009 to Nov. 2011. To analyze the effect of Nakdan weir construction on benthic macroinvertebrates, we studied 2 sites around Nakdan weir (upstream and downstream) from 2007 to 2014. The average numbers of species and individuals were decreased after the construction (in 2012~2014, 51 species $895inds.\;m^{-2}$) than before construction (in 2007~2009, 25 species $84inds.\;m^{-2}$), especially in upstream site of Nakdan weir. After the construction, especially in 2012, dominance indices (DI) were increased by the decline of some specific taxon population, such as Ephemeroptera and Trichoptera, etc. After construction, individual ratios of GC (Gathering Collectors) and P (Predator) of FFGs (Functional feeding groups) and BU (Burrowers) of HOGs (Habitat orientation groups) were higher than before construction. So the results of this study indicate that the changes by a weir construction, such as the decline of shallow depth area, reduced velocity of water flow and increased ratio of sand bed, etc., can affect the benthic macroinvertebrate communities variously.

• Economic and Environmental Geology
• /
• v.53 no.1
• /
• pp.87-98
• /
• 2020

The bird track fossil site in Haman Formation is divided into seven sedimental layers by the sedimentary structures, lithofacies and sequences. The bird tracks top on the highest layer, which includes ripple marks and suncracks. The layer has lithofacies with reddish grey siltstone and dark grey mudstone, alternately. As an analysis for the same rocks of the fossil site, physical properties show on mean values for 0.62% of absorption rate, 1.64% of porosity and 2.63 of specific gravity. Rock-forming minerals composed mainly of plagioclase, quartz, calcite, chlorite and mica. Meanwhile, we executed an experiments based on the petrography and weatherings to find a proper consolidants. In the experiments, the OH 100 reagent proved stable aspect and the lowest transition rate in terms of weight and chromaticity. Also, it showed the highest increase in ultrasonic velocity, improving the physical properties of the rocks. In the case of applying the OH 100 with antihygro, an swelling inhibitors on the sedimentary rocks, the chromaticity indicated an stable transition aspect. When it comes to the physical properties, the antihygro also decreases the porosity effectively. Thus, the most proper method for the fossil site of Haman Formation is to apply antihygro and OH 100 reagents since the rocks includes clay minerals that show swelling characteristics. However, this result is deduced from an indoor application experiments, leaving the necessity of verification how these reagents would affect the bird tracks site under the field condition.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.1
• /
• pp.40-49
• /
• 1986

Crack, craze and void are common defects which may be found in the bulk of polymeric materials such as either themoplastics or thermosets. The healing phenomena, autohesion, of these defects are known to be a intrinsic material property of various polymeric materials. However, only a few experimental and theoretical investigations on crack, void and craze healing phenomena for various polymeric materials have been reported up to date [1, 2, 3]. This may be partly due to the complications of healing processes and lacking of appropriate theoretical developments. Recently, some investigators have been urged to study the healing phenomena of various polymenic materials since the significance of the use of polymer based alloys or composites has been raised in terms of specific strength and energy saving. In the earlier published reports [1, 2, 3, 4], the crack and void healing velocity, healing toughness and some other healing mechanical and physical properties were measured experimentally and compared with predicted values by utilizing a simple model such as the reptation model under some resonable assumptions. It seems, however, that the general acceptance of the proposed modeling analyses is yet open question. The crack healing processes seem to be complicate and highly dependent on the state of virgin material in terms of mechanical and physical properties. Furthermore, it is also strongly dependent on the histories of crack, craze and void development including fracture suface morphology, the shape of void and the degree of disentanglement of fibril in the craze. The rate of crack healing may be a function of environmental factors such as healing temperature, time and pressure which gives different contact configurations between two separated surfaces. It seems to be reasonable to assume that the crack healing processes may be divided in several distinguished steps like stress relaxation with molecular chain arrangement, surface contact (wetting), inter- diffusion process and com;oete healing (to obtain the original strength). In this context, it is likely that we no longer have to accept the limitation of cumulative damage theories and fatigue life if it is probable to remove the defects such as crack, craze and void and to restore the original strength of polymers or polymer based compowites by suitable choice of healing histories and methods. In this paper, we wish to present a very simple and intuitive theoretical model for the prediction of healed fracture toughness of cracked or defective polymeric components. The central idea of this investigation, thus, may be the modeling of behavior of chain molecules under healing conditions including the effects of chain scission on the healing processes. The validity of this proposed model will be studied by making comparisons between theoretically predicted values and experimentally determined results in near future and will be reported elsewhere.

• Tunnel and Underground Space
• /
• v.19 no.2
• /
• pp.146-157
• /
• 2009

An experimental study of accelerated weathering on mudstone sample specimens from Haman, Gyeongnam was performed to investigate the variations of physico-mechanical properties of deteriorated rocks due to freeze-thaw weathering. Each complete cycle of freeze and thaw lasted 24 hours, comprising 2 hours of saturating in vacuum chamber, 8 hours of freezing at $-16{\pm}1^{\circ}C$ and 14 hours of thawing at room temperature. Total of 55 cycles of freeze-thaw were completed with measuring the index properties as well as geometries of microfractures. The measured specific gravity and P-wave velocity found to decrease with increasing freeze-thaw cycles. On the other hand, absorption ratio and effective porosity were continuously increased with increasing freeze-thaw cycles. It was found that the index properties of deteriorated sample specimen depend on its initial properties and flaws in rock. The size and density of the traces of the microfracture on slab specimen exhibited abrupt changes after 30 cycles of freeze-thaw weathering. The results obtained in this study show that the box fractal dimension($D_B$) given in this paper has the strong capability of quantifying the size and density of the microfracture.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.200-214
• /
• 1993

This paper presents the results of fluidelastic instability analysis performed for the U-tube bundle of a Westinghouse model 51 steam generator, one of the recirculating types designed at an early stage, in which the principal region of external cross-flow is associated with the U-bend portion of tube. The prerequisites for this analysis are detailed informations of the secondary side flow conditions in the steam generator and the free vibration behaviours of the U-tubes. In this study, the three-dimensional two-phase flow field in the steam generator has been calculated employing the ATHOS3 steam generator two-phase flow code and the ANSYS engineering analysis code has been used to calculate the free vibration responses of specific U tubes under consideration. The assessment of the potential instability for the suspect U-tubes, which is the final analysis process of the present work, has been accomplished by combining the secondary side velocity and density distributions obtained from the ATHOS3 prediction with the relative modal displacement and natural frequency data calculated using the ANSYS code. The damping of tubes in two-phase flow has been deduced from the existing experimental data by taking into account the secondary side void fraction effect. In operation of the steam generator, the tube support conditions at the tube-to-tube support plate intersections due to either tube denting degradation or deposition of tube support plate corrosion products or ingression of dregs. Thus, various hypothetical cases regarding the tube support conditions at the tube-to-tube support plate intersections have been considered to investigate the clamped support effects on the forced vibration response of the tube. Also, the effect of anti-vibration bars support in the curved portion of tube has been examined.

• Journal of Animal Environmental Science
• /
• v.17 no.2
• /
• pp.93-100
• /
• 2011

This study was conducted to verify the applicability of robot milking system through acquisition and analysis of model teat's position information using scanning range finder (SRF). Model teats, same size and shape as real teats, were designed to analyze the properties according to the material, distance error and angle error of the sensor. In addition, 2-dimensional distance information of each teats was obtained at same time with 4 teat models and the result were as follows. 1. In the case of the fingers on the experiment for selection of materials for teat model, the distance error was from 4.3 mm to 1.3 mm, average was 2.8 mm as a minimum record. In the case of rubber material, average distance error was 4.3 mm. So, this material was considered to be a most suitable model. 2. The distance error was maximum at 100 mm distance. The more distance increased, the less error increased up to 300 mm. Then the error increased after 300 mm and decreased again. 3. The maximum angle error of 10.1 mm was measured at $170^{\circ}$, in case of $70^{\circ}$ the error was 0.2 mm as a minimum value. There was no specific tendency to error of angle. 4. In the 2-dimensional location error for 4 teat models, distance error was 3.8 mm as minimum and 7.2 mm as maximum. The angle error was $1.2^{\circ}$ as maximum. All of errors were included within the accuracy of sensor, the robot milking system was considered to be applicable to measure the distance of teats due to the measuring velocity of SRF and the hole size of teat-cup.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.9
• /
• pp.53-68
• /
• 2015

Longitudinal strain is an important component of seismic design for buried pipelines. A design procedure which determines the wavelength from site natural period and shear wave velocity of the soil layer and closed-form solutions of pipelines under a harmonic motion is typically used in design. However, the applicability of the procedure has not yet been thoroughly investigated. In this paper, displacement-time histories extracted from 1D site response analyses are used in 3D shell-spring model to accurately predict the response of pipelines. The results are closely compared to those from the design procedure. The area of interest is East Siberia. Performing a site response analysis to determine site specific displacement time history is highlighted. The site natural period may be used to predict the predominant period of the acceleration time history, but cannot be used to estimate the predominant period of the displacement time history. If an accurate estimate of the predominant period of the displacement time history is provided, it is demonstrated that the design equation can be successfully used to predict the response of pipelines.

• The Journal of Engineering Geology
• /
• v.30 no.2
• /
• pp.161-173
• /
• 2020

This study is to examine the engineering characteristics of colunmar joints in Mudeugsan National Park, a global geopark. For these purposes, physical and mechanical properties of Mudeungsan Tuff, evaluation for the weathering degree of columnar joints, and crack behavior monitoring in columnar joints were conducted. The physical properties of Mudeungsan tuff were 1.02% for the average porosity, 0.38% for the average absorption, 2.69 g/㎤ for the average specific gravity, and 4,948 m/s for the average elastic wave velocity. Its mechanical properties were 337 MPa for the average uniaxial compressive strength, 68 GPa for the average elastic modulus, 0.29 for the average Poisson's ratio, 41.3 MPa for the average cohesion strength, and 62.8° for the average friction angle. the average rebound Q-value of the silver Schmidt hammer for the three columnar joint blocks at the Ipseok-dae was shown as 49.3. when this value is converted into uniaxial compressive strength, it becomes 70.5 MPa, which is about 21% of the uniaxial compression strength of Mudeungsan tuff. In addition, according to the results of crack monitoring measurements for the three columnar joint blocks at the Ipseok-dae, the crack behavior is less than 1 mm, so it is believed that its behavior in Ipseak-dae columnar joints has hardly occured to date.