• 소성∙가공
• /
• 제14권3호
• /
• pp.200-206
• /
• 2005

In general, a lot of small electrode is needed for making precision injection molds, such as cell phone mold and precision connector mold, because of the limitations of NC milling process. Those small electrodes usually have very simple shapes and the actual cutting time is so short, but many NC programs and set-up process, a very complicated and time consuming Job, are needed for each electrode. This paper deals the method for increasing the productivity of machining electrodes. In this work, the process standardization of machining electrode was done and special jig fer machining small electrodes was developed. Automatic tool path optimization software was also developed to minimize tool changing time. In addition, in-line cutting tool measuring system was adopted. The productivity of machining for small electrode has been increased up to $100\%$.

• 한국레이저가공학회지
• /
• 제2권3호
• /
• pp.32-41
• /
• 1999

This study is about Jig used in wiring when we make Probecard and Large Scale Intergrated Electronic Circuit. The most universal wiring method is molding with Bond. Polymer film is punched down and adhesives is applied after wiring. Due to shrinkage and modification many problems still have happened in the process of molding. To solve these problems, ceramic plate was introduced in the study. Using Laser, an experiment of microhole treatment on ceramic plate was proceeded. Laser energy, assistance gas, and special features by purity degree were analyzed with the 35W low capacity YAG-Laser. In the condition of energy 0.08J, frequency 20Hz and interval time 200$mutextrm{s}$, about 70${\mu}{\textrm}{m}$ microhole was adequate for the Probecard Jig. In the purity experiment of ceramic materials, high purity ceramic met with good result for microhole. But the price is too high. The shape and size of holes machined combustion gas $O_2$ were better than those in $N_2$ and Ar, the inert gas.

• Journal of Interdisciplinary Genomics
• /
• 제5권2호
• /
• pp.24-28
• /
• 2023

Chromosomal microarray (CMA) is primarily recommended for detecting clinically significant copy number variants (CNVs) in the genetic diagnosis of developmental delay, intellectual disability, autism, and congenital malformations. Prenatal CMA is recommended when a fetus has major congenital malformations. The main principles of CMA can be divided into array comparative genomic hybridization and single-nucleotide polymorphism arrays. In the current CMA platforms, these two principles are combined, and detection of genetic abnormalities including CNVs and absence of heterozygosity is facilitated. In this review, I described practical assessment of CMA testing regarding to laboratory management of CMA, interpretation of CNVs, and special considerations for comprehensive genetic counseling.

• 수산해양기술연구
• /
• 제50권3호
• /
• pp.252-261
• /
• 2014

Marine casualties originated from fishing vessel occupied about 70% of the whole marine casualties in Korea from 2001 to 2010, this ratio was not much changed as it was before. Therefore a pragmatic counterplan to decrease of casualties in fishing vessel is indispensable for reduction of the nationwide marine casualties. But since the casualties occurred by fishing vessel may have a different causes and counterplan according to the operating type of it, in this paper, fishing vessels classified into 12 types by operating method and inspected the causes and counterplan for that. The operating type of fishing vessel occurred the specific casualties more were jig boat in collisions and fire explosion, trap fishing boat, mixed fishing boats and inshore gill netter in collisions, stow netter in machinery damages and capsizing, offshore gill netter in machinery damages, fish carrier in collisions. It must be emphasized that the higher ranked types of vessels, especially jig boat have to take special care to the approaching vessels under way, trap fishing boat to rear look out and mixed fishing boat must keep on safety speed and be taken an education for advance the skill of operating radar as well. For all 12 types of fishing vessel, it is necessary for an operator to make strict precaution on the other vessel under way systematically and keep the regulation for preventing collisions, and for an engineer on watch to make a check the electricity and the engines periodically for reduction the fire explosion and machinery damages.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권6호
• /
• pp.981-988
• /
• 2008

This paper describes a development of automatic measuring device for cylinder liner wear amount. An operator should regularly measure the wear amount of the cylinder liner to prevent the wear amount of the cylinder liner from exceeding the maximum limit specific to the engine type. In previous methods. an operator entered the inside of the cylinder liner on a ladder and measured the amount of wear using a inside micrometer. Such method is unpleasant in severe environments and full of hazards. In addition, in order to enter the cylinder, the piston head had to be detached. requiring much time and money. In order to solve these problems, a new measuring device that consists of two measuring units and a special install jig is developed. The measuring units are installed through the scavenging air port by the install jig and measures the wear amount during 1 revolution of crankshaft. so detaching of the cylinder head and entering inside the cylinder liner are not required.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권4호
• /
• pp.415-421
• /
• 2014

In this paper, reactorless high efficiency boost DC/DC converter for EV is proposed. In proposed converter, improves efficiency because decrease power loss when the switches are turned on/off using zero current switching (ZCS) at all switch of primary full bridge. By replacing reactance ingredients of L-C resonance circuit for ZCS with leakage inductance ingredients of high frequency transformer, it reduces system size and expense because of not add special reactor. For validity verification of proposed converter, in the paper implements simulation using PSIM and perform experiment by making 5KW DC/DC converter. In experimental results, efficiency of proposed converter conformed superiority.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 학술대회 논문집
• /
• pp.339-342
• /
• 2004

It is research about special quality of ozone gas concentration and dissolved ozone concentration that show according to change of flow rate when liquefied ozone gas in water. If increase flow rate of ozone gas, ozone concentration increases being proportional and amount to fixed flow rate, dissolved ozone concentration was measured low. When ozone concentration How rate 1000 [ppm], dissolved ozone concentration smelted to flow rate 1.5[Q] for 28 [min] is $0.1740{\sim}0.8020[mg/l]$. Could know that half-life is most short by 3 minutes 8 seconds in flow rate 1.5 [Q]. And ozone smelted 20 minutes later after half-life measurement became disjointing all.

• 한국생산제조학회지
• /
• 제19권6호
• /
• pp.768-775
• /
• 2010

Automotive industry is a major business area in this country and it becomes more and more important. In order to maintain high quality of vehicles, every parts should be inspected. Among them the inspection job of the knuckle bracket holes of the outer tube of shock-absorber has been done manually until now. So, it takes long time and every product can not be inspected. An automatized inspection system was proposed utilizing machine vision technology, which was composed of a slit beam laser, CCD camera, image processing computer, special jig and illuminating back lights. An algorithm which could process images of the laser and bracket holes, then gave the position, radius, roundness of the holes, was developed. This system was applied for the good and no good products and the performance was confirmed.

• 산업공학
• /
• 제25권1호
• /
• pp.87-95
• /
• 2012

Very special and tentative considerations including emotional aspects are required to apply any new mechanism and methodologies for manufacturing fields due to several reasons. This study reviews the characteristics of manufacturing collaborations through specific cases applied digital engineering to enhance the collaboration performance in manufacturing domains. Two cases of collaboration related with automotive manufacturing process are analyzed to extract meaningful insights for better collaboration model suggestions. The first case deals the robot simulation to find out advance errors in jig and fixture design during the various welding process of body-in-whites. The effective communication protocol to share their idea and agreed schedules are essential for this collaboration. More severe requirement of collaboration between R&D and manufacturing departments are studied in the second case for e-coating process. The invisible barriers among different departments are lowered by the process application of Computer Aided Engineering which can make sure their own interesting effectively. Those technical and managerial suggestions can be used when the information system and standard process are sought to implement and update not only when innovation projects are executed.

• 한국주조공학회지
• /
• 제25권6호
• /
• pp.254-258
• /
• 2005

Semisolid process is possible in any material system possessing a freezing range where the microstructure should consist of the nondendritic globular solid phase separated and enclosed by the liquid phase, referred to as semisolid slurry. There are two primary semisolid processing routes, thixocasting and rheocasting. Especially, rheocasting process has become a new focus in the field of semisolid process because of its many advantages such as no special billet required and possibility of in-house scrap recycling, compared with the thixocasting process. In-Ladle direct thermal control (DTC) rheocasting has been developed, based on the fact that there is slurry and mush transition in every molten metal and the transition, which normally occurs in the range of liquid traction of 0.1 to 0.6, could be controlled by controlling solid shape and relative solid-liquid interfacial energy. In this study, A356 Al alloy was investigated to verify In-Ladle DTC rheocasting for obtaining semisolid slurry. Modeling of heat transfer was carried out to investigate the effect of pouring temperature and ladle material, geometry and temperature and the simulation results were compared with the actual experiments.