• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.1
• /
• pp.67-77
• /
• 1998

Homogeneous liquids of Ni-21.5Nb-2.5Al and Ni-23.3Nb eutectic superalloys were solidified into Ni/$Ni_3$Al-$Ni_3$Nb(${\gamma}$/${\gamma}$'-${\delta}$)and Ni-Ni/$Ni_3$Nb(${\gamma}$-${\delta}$) phase by directional solidification and the effect of interlamellar spacing on microsturctural stability at high temperatures, hardness variation with growth rate was studied. The interlamellar spacing(${\lambda}$) in the eutectics was varied with the growth rate(R), corresponding to "${\lambda}^2$R ＝Constant" relationship. Isothermal heat treatments of the eutectics used in this study, provided the microstructural stability improvement at hight temperature as the interlamellar spacing increases. It was also seen that the hardness improvement is made with the growth raterowth rate

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09b
• /
• pp.141-146
• /
• 2010

To investigate the effect of drainage spacing and smear on the rate of consolidation, a large consolidation chamber and mandrel insertion device were developed. After the occurrence of smear by installation of sand drain, model ground was consolidated in either overconsolidated or normally consolidated state. As smear effect increases and thus drain spacing decreases, total settlement increase in overconsolidated state but has no effect in normally consolidated state. Efficiency of vertical drain decreases and consequently consolidation time increases in all tests as smear effect becomes significant.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.2
• /
• pp.245-253
• /
• 2002

This study was focused on the effect of concrete strength and lateral ties of concrete columns using high-strength concrete. Thirty-six concrete columns with 20cm square cross-section were tested. Experimental parameters included the concrete strength, the distribution of longitudinal bars and the volumetric ratio, yield strength, spacing of lateral ties. From the experiments, we found that: 1) the increasing rate of the strength and ductility of concrete columns caused by confinement of lateral ties was decreasing, as the concrete strength increased. 2) The high volumetric ratio and the reduction of tie spacing had a tendency to enhance the strength and improve the ductility. 3) The high-strength concrete columns required high volumetric ratio of lateral ties to maintain the proper strength and ductility. It was observed that the current AIK design code to specify the maximum tie spacing of high-strength concrete columns led to the poor strength and ductility for seismic design.

• Journal of Korea Foundry Society
• /
• v.4 no.4
• /
• pp.5-13
• /
• 1984

This paper is presented for showing the effect of cooling rate on dendrite arm spacing, correlated with the chilling power of molding materials (conventional plaster, foamed plaster, silica sand) and section thickness, and also showing relationship between dendrite arm spacing and mechanical properties for an aluminum - 8.6 percent silicon - 3.6 percent copper alloy. Local solidification time $(t_f)$ and secondary dendrite arm spacing (d) could be varied widely in accordance with the molding materials and casting thickness, and the following relationship is obtained: $d=9.4t_f\;^{0.31}$ A good correlation between dendrite arm spacing and mechanical properties such as ultimate tensile strength, yield strength, hardness was found, that is, mechanical properties decreased in a linear manner with increase in log of secondary dendrite arm spacing. Ultimate tensile strength in conventional plaster mold casting decreased by 15 percent comparing with the sand casting, where as in foamed plaster mold casting, it decreased by 30 percent comparing with the sand casting. From those results, it has been verified that DAS might be the most representative parameter for predicting mechanical properties varing with the different cooling condition.

• Computers and Concrete
• /
• v.20 no.4
• /
• pp.429-437
• /
• 2017

In this study, the effect of the tensile strength and ratio of disc spacing to penetration depth on the efficiency of tunnel boring machine (TBM) is investigated using Particle flow code (PFC) in two dimensions. Models with dimensions of $150{\times}70mm$ made of rocks with four different tensile strength values of 5 MPa, 10 MPa, 15 MPa and 20 MPa were separately analyzed and two "U" shape cutters with width of 10 mm were penetrated into the rock model by velocity rate of 0.1 mm/s. The spacing between cutters was also varied in this study. Failure patterns for 5 different penetration depths of 3 mm, 4 mm, 5 mm, 6 mm, and 7 mm were registered. Totally 100 indentation test were performed to study the optimal tool-rock interaction. An equation relating mechanical rock properties with geometric characteristics for the optimal TBM performance is proposed. The results of numerical simulations show that the effective rock-cutting condition corresponding to the minimum specific energy can be estimated by an optimized disc spacing to penetration depth, which, in fact, is found to be proportional to the rock's tensile strength.

• Journal of KIISE
• /
• v.42 no.1
• /
• pp.68-75
• /
• 2015

This paper proposes a method for the automatic word spacing of unsegmented Korean sentences. In our method, eojeol monograms are used for word spacing as opposed to the syllable n-grams that have been used in previous studies. The use of a Korean morphological analyzer is limited to the correction of typical word spacing errors. Our method gives a 98.06% syllable accuracy and a 94.15% eojeol recall, when 10-fold cross-validated with the Sejong corpus, after filtering out non-hangul eojeols. The processing rate is 250K eojeols or 1.8 MB per second on a typical personal computer. Syllable accuracy and eojeol recall are related to the size of the eojeol dictionary, better performance is expected with a bigger corpus.

• Journal of Korea Foundry Society
• /
• v.17 no.6
• /
• pp.608-614
• /
• 1997

The effect of mold preheating temperature on the microstructure such as grain size, eutectic silicon morphology was investigated for the Al-7wt%Si-0.3wt%Mg alloy. Microstructural variations have been characterized as a function of Sr addition and cooling rate during solidification. Microstructures were correlated with cooling rate, local solidification time and eutectic nucleation temperature, etc. In this study, Sr addition caused increase of local solidification time, undercooling and reduction of eutectic plateau temperature. In logarithmic scale, local solidification time was in inverse proportion to cooling rate. Eutectic nucleation temperature was in inverse proportion to cooling rate of logarithmic scale. Increasing the cooling rate refined dendrite arm spacing and eutectic silicon. Dendrite arm spacing was logarithmically in inverse proportion to cooling rate. Without modifier addition, eutectic silicon was modified at cooling rate of $7^{\circ}C/s$ or higher.

• 한국연소학회:학술대회논문집
• /
• 2007.05a
• /
• pp.47-53
• /
• 2007

The laminar combustion characteristics of interacting coal particles in a convective flow are numerically investigated at particle arrangement and size difference. The numerical simulations, which use the two-step global reaction model to account for the surrounding gas effect, show the detailed interaction among the inter-space particles, undergoing devolatilization and subsequent char burning. Several parametric studies, which include the effect of the gas temperature (1700 K), high pressure(10 atm) and variation in geometrical arrangement of the particle diameter on the volatile release rate and the char combustion rate, have been carried out. The comparison indicates that the shift to the multiple particle arrangement resulted in the substantial change of the combustion characteristics and that the volatile release rate of the interacting coal particles exhibits a strong dependency on the particle spacing and size difference.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.1 s.232
• /
• pp.16-26
• /
• 2005

Air-cooled heat sinks are employed in many electronic cooling applications since they provide significant heat transfer enhancement and operational flexibility. Strip-shaped fin heat sink is of interest and needs to be investigated as general cooling products for more applicability. The purposes of this study are to evaluate heat sink performance without bypass flow condition and to determine optimal heat sink geometries. The results show that the decreasing rate of thermal resistance of a heat sink decreases with increasing inlet air velocity, and the increasing rate of pressure drop increases with increasing inlet air velocity, but is not affected by input power. The increasing rate of optimal longitudinal fin spacing is larger than that of transverse fin spacing. The strip fin heat sink tested in this study showed better cooling performance compared to that of other plate fin type.matism. 2004; 50(11): 3504-3515.

• Journal of Korea Foundry Society
• /
• v.37 no.4
• /
• pp.108-114
• /
• 2017

In this study, we investigated the effect of the Si content on the secondary dendrite arm spacing (SDAS) of hypoeutectic Al-Si binary alloys in the range of 4~10 wt% Si. Cooling curves were measured during the solidification of the alloy cast in a step-wise mold. We compared two kinds of solidification time: the first is the total solidification time for both dendritic and eutectic growth, and the second is the solidification time for only dendritic growth. The proportional constant in the relationship between SDAS and cooling rate was estimated, as this constant represents the stability of the cast microstructure. The proportional constant decreased with the Si contents from 4 wt% to 8 wt%, and it remains relatively uniform with up to 10 wt% of Si.