• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.1 s.256
• /
• pp.8-15
• /
• 2007

The jet impingement cooling characteristics are investigated experimentally. The study is motivated by the potential application of local hot spot cooling by means of the vortex tube. The purposes of this research are to examine the effect of the nozzle-block spacing and flow rate. The results of jet through vortex tube is compared with ones of circular Jet. Flow visualization by the smoke-wire technique is also performed to investigate the flow structure. As the nozzle-block spacing is increased and flow rate decreased, the cooling effect of the Jet through the vortex tube decreases mere remarkably than that of the circular jet. So the cooling effect for the jet through the vortex tube is higher than that for the circular jet at $H/D{\leq}3$, $Q{\geq}10m^3/h$.

• Journal of the Korean Ceramic Society
• /
• v.22 no.3
• /
• pp.41-45
• /
• 1985

An experimental study has been carried out to investigate the effect of growth rate V and time on secondary dendrite arm spacing of cristobalite dendrites in $14.6K_2O-85.4SiO_2$ glass by means of x-ray diffractormetry optical microscopy and scanning electron microscopy The scanning lectron microscopy reveals a two-phase layer of dendritic crystals and interstitial melt which grow from the surface at a constant rate. Based on this experiment secondary arm spacing is proportional to V-0.24 and dendrite coarsening during isothermal holding shows that the secondary arm spacing increases with increasing heat-treatment time.

• Journal of Biosystems Engineering
• /
• v.22 no.2
• /
• pp.127-136
• /
• 1997

This study was accomplished to develop a pneumatic granular applicator that can be attached to the conventional ride-on rice transplanter. Operating conditions of a metering device for the applicator were determined so as to obtain the required discharge rate of granules for field application. The shape and size of diffuser was selected for the applicator and the spacing between diffusers on a boom and the boom height were determined as an optimal application condition for uniform distribution. The diffuser spacing of 1m for the fertilizer and the diffuser spacing of 0.8m for the pesticide at the boom height over 0.8m were acceptable.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.1
• /
• pp.131-139
• /
• 1999

Experimental investigations on flame spread in droplet arrays have been conducted under supercritical ambient pressures of fuel droplet. Flame spread rates are measured for n-Decane droplet of diameters of 0.75 and 1.0mm, using high speed images of OH chemiluminescence up to 3.0MPa. The pattern of flame spread is categorized into two: a continuous mode and an intermittent one. There exists a limit droplet spacing, above which flame spread does not occur. Flame spread rate with the decrease of droplet spacing increases and then decreases after takin& a maximum. It is also seen that there exists a limit ambient pressure, above which flame spread does not occur. Flame spread rate decreases monotonically with the increase of ambient pressure. Exceptionally, In the case of a small droplet spacing, flame spread with the increase of ambient pressure is extended to supercritical pressures of fuel droplet. This is caused by enhanced vaporization with the increase of ambient pressure. Consequently, in flame spread with droplet droplet spacing, the relative position of flame to droplet spacing plays an important role. The monotonic decrease with ambient pressure is mainly related to the reduction of flame radius in subcritical pressures and the extension to supercritical pressures of flame spread is caused by the reduction of ignition time of unburnt droplet due to the enhanced vaporization at supercritical pressures.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3B
• /
• pp.271-278
• /
• 2006

In design of groyne series, groyne spacing is a important factor and have an effect on not only the characteristics of backward and recirculation flow in groyne zone but also flow field in main channel. It is necessary study about flow pattern of recirculation zone and main channel that is a cause of bad change, local scour and bank erosion by groyne spacing. In this study, flow variation of groyne zone and main chanel for spacing of groynes were analyzed from the experiment results in order to offer a fundamental data that can be used to decide the proper groyne spacing. Experiments were conducted 12 cases for groyne spacing(L) by groyne length(l) rate and the velocity profile was measured using LSPIV and ADV. From the results, two vortex flows developed in recirculation zone for L/l=3~9 and three vortex flows developed over L/l=10. The velocity of backward flow in recirculation zone was decreased up to 20% over L/l=4. The velocity of main channel flow was increased from 1.3 to 2.0 times by groyne spacing and the rate of velocity increased by increasing groyne spacing. The maximum velocity occurred in 0.7~0.8 times of groyne spacing downstream of upper groyne.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.4
• /
• pp.77-87
• /
• 2011

To investigate the effect of drainage spacing and smear on the rate of consolidation and the efficiency of vertical drain method, a series of consolidation tests with a large consolidation chamber and special equipment for inserting mandrels were conducted. As the smeared region increases, total settlement in over-consolidated clay increases whereas apparent change in settlement does not appear in normally consolidated clay. Vertical drain generally accelerates the rate of consolidation, while it could also deteriorate the efficiency of vertical drain method even for the decreasing drainage length and spacing ratio.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.109-120
• /
• 2005

In this paper, bit error rate (BER) characteristics, sensitivity and minimum allowable launching power are numerically investigated as a function of amplifier spacing that consisted of 1,200 km WDM systems with MSSI method. It is conformed that the sensitivity and minimum allowable launching power are gradually degraded as amplifier spacings are gradually expanded, but those are not largely affected by modulation format. The sensitivity of RZ transmission system is smaller than that of NRZ transmission system, but minimum allowable launching power of NRZ transmission system is smaller than that of RZ transmission system. And, it is confirmed that the best amplifier spacing in NRZ and RZ transmission system is less than 50 km, because the sensitivity and minimum allowable launching power are less affected by fiber dispersion, channel wavelength and pump light power.

• Journal of Korean Society of Transportation
• /
• v.24 no.6 s.92
• /
• pp.21-32
• /
• 2006

The purpose of this study is to determine the economical standard for road signs by verifying the difference in driver's legibility time with respect to the spacing of letters on the toad signs. Laboratory simulations were conducted to confirm the difference in legibility time for six target signs of different spacing. Also. a binary logit model was used to find the main factors, which could lower the rate if misreading. This model involves not only a simple enlargement of signs but also a suitable match of letters and signs along with the optimal spacing of the text letters on the road signs to increase the legibility of the sign. The result of this study verified the importance of spacing in road signs and Proved itself to be an effective method to determine the future standard for the road signs.

• Structural Engineering and Mechanics
• /
• v.83 no.4
• /
• pp.495-513
• /
• 2022

This paper aims to study the fracture mechanism of rocks under the 'u'shape cutters considering the effects of crack (pre-existing crack) distances, crack spacing and crack inclination angles. The effects of loading rates on the rock fragmentation underneath these cutters have been also studied. For this purpose, nine experimental samples with dimensions of 5 cm×10 cm×10 cm consisting of the non-persistent cracks were prepared. The first three specimens' sets had one non-persistent crack (pre-existing crack) with a length of 2 cm and angularity of 0°, 45°, and 90°. The spacing between the crack and the "u" shape cutter was 2 cm. The second three specimens" set had one non-persistent crack with a length of 2 cm and angularity of 0°, 45°, and 90° but the spacing between pre-existing crack and the "u" shape cutter was 4 cm. The third three specimens'set has two non-persistent cracks with lengths of 2 cm and angularity of 0°, 45° and 90°. The spacing between the upper crack and the "u" shape cutter was 2 cm and the spacing between the lower crack and the upper crack was 2 cm. The samples were tested under a loading rate of 0.005 mm/s. concurrent with the experimental investigation. The numerical simulations were performed on the modeled samples with non-persistent cracks using PFC2D. These models were tested under three different loading rates of 0.005 mm/s, 0.01 mm/sec and 0.02 mm/sec. These results show that the crack number, crack spacing, crack angularity, and loading rate has important effects on the crack growth mechanism in the rocks underneath the "u" shape cutters. In addition, the failure modes and the fracture patterns in the experimental tests and numerical simulations are similar to one another showing the validity and accuracy of the current study.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.1
• /
• pp.13-19
• /
• 2012

Thermal performance of an impinging cooling module for 150 W class high power LEDs have been investigated numerically and experimentally. Parametric studies were performed to compare the effect of several design parameters such as nozzle number, nozzle spacing, coolant flow rate, and impinging distance. The experiments were also carried out in order to validate the numerical results and the comparison between the experimental and numerical results showed good agreement. It is found that the overall thermal resistance of impinging cooling module strongly depends on the nozzle number, nozzle spacing, flow rate, and impinging distance. This results showed the optimized operating condition when number of nozzles is 25, nozzles spacing is 4mm, flow rate is 2.70 lpm, distance between nozzles and impinging surface is 2 mm.