• Journal of the Korea Society of Computer and Information
• /
• v.6 no.1
• /
• pp.45-50
• /
• 2001

Congestion may take place in the ATM network because of high-speed cell transmission features, and cell delay and loss also can be caused by unexpected traffic variation. Thus. traffic control mechanisms are needed. One of them to decrease congestion is the cell shaping. This paper proposes a hybrid type cell shaper composed of a Leaky Bucket with token pool, EWMA with time window, and a spacing control buffer. The simulator BONeS with the ON/OFF traffic source model evaluates the performance of the proposed cell shaping method. Simulation results show that the cell shaping concerning the respective source traffics is adapted to and then controlled on the mean bit rate.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.450-457
• /
• 2003

In this paper, we studied the effect of asymmetrical 3rd order IMD of power amplifier due to changes in modulation frequency on IMD cancellation performance. The phase extraction method for determining asymmetric rate for phase distortion of IMD is proposed and the phase difference between lower and upper 3rd order IMD is measured by this method. The phase compensation circuit to decrease the phase difference is also designed and fabricated. From the measurement results using the phase compensation circuit applied to 5 W RF power amplifier fur PCS applications, the 3rd order IMD cancellation performance can be achieved up to 2-tone spacing 1.5 MHz (phase difference within 10$^{\circ}$).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.5
• /
• pp.698-707
• /
• 1998

A simplified model for predicting microsegregation during columnar-dendritic solidification of binary alloys is developed, in which back diffusion, dendrite arm coarsening and dendrite tip undercooling are simultaneously incorporated. The inclusion of tip undercooling is accomplished by modifying the initial conditions of the existing solute diffusion model, in such forms that tip undercooling depresses the beginning of solidification below the liquidus temperature, and that the secondary arm spacing evolves in accordance with the minimum undercooling theory. Sample calculations for the well-known benchmark system show that the present predictions not only consist with the extablished limiting cases, but also agree favorably with the available experimental data within a reasonable tolerance. In particular, a typical decreasing trend in the eutectic fraction at high cooling rates is successfully resolved. Comparison of the individual and combined effects of characteristic parameters in reference with the limiting cases reveals the interactions among parameters. Every parameter plays the role of reducing the eutectic fraction, and the degree of influence depends primarily on the cooling rate. Coarsening enhances the effect of tip undercooling, while suppressing that of back diffusion. A vigorous back diffusion seems to restrain the apperance of the undercooling effect. Overall, each contribution of the three parameters to microsegregation is estimated to be of the same order, which suffices to justify the present study.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.4
• /
• pp.29-37
• /
• 2003

Using a wind tunnel testing, the aerodynamic load characteristics of an elliptic airfoil was described. The experimental data was obtained for angles of attack $-20^{\circ}$ to $+20^{\circ}$ with $2^{\circ}$ increments at a chord Reynolds number of $0.99{\times}105$ and $2.48{\times}105$. For each test case, chordwise suction pressure distributions and wake surveys were obtained. Static pressure measurements were made over a 10 sec averaging time at a 10 Hz sampling rate. For each case, wake survey was conducted with a pilot-static probe at 1.0c downstream from the trailing edge at very fine spacing to resolve the wake velocity deficit profile. As can be expected, suction pressure coefficient was increased with angle of attack. The normal force, CNmax, appeared peak value at the incidence angle of $12^{\circ}~14^{\circ}$, and the significant increase in profile drag at this range of angles of attack.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.6
• /
• pp.788-794
• /
• 1985

A study on the number density in a dual beam LDV is carried out with moving particles of various irregular arrangements. Ratious of the particle diameter to the particle to the fringe Spacing are D/.delta. = 0.3, 0.5, 1.0 and 1.5. In the case of the small number of moving particles(N<10), the visibility is influenced much by the difference of the phase of particles for one side fringe and the change in visibility is shown remarkable. In the case of the larger number of particles, the decreasing rate for visibility on the graph is smooth because the effect of the phase difference of particles is decreased by more unitorm distribution of particles over fringes. And the formula of the number density on the basis of probability is fairly compared with experimental values.

• Journal of Powder Materials
• /
• v.18 no.1
• /
• pp.24-28
• /
• 2011

Effect of Cu content on microstructural and magnetic properties of a $(Nd_{26.06},Dy_{6.51})Fe_{bal.}$ $Cu_xB_{0.97}$(wt.%), (x = 0.2, 0.3, 0.4, 0.5) strip-cast was studied. The average inter-lamellar spacing in the free surface and wheel side of the strip cast increased as the Cu content increases. The grain uniformity, the grain alignment, and (00L) texture of the strip cast increased with Cu contents up to 0.4 wt.%. These microstructural changes were attributed to the decrease of the effective cooling rate of the melted alloy caused by the decrease of the melting temperature of resulting from Cu addition. Coercivity and remanence were increased because of the grain alignment and (00L) texture improvement with Cu contents up to 0.4 wt.%.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.12
• /
• pp.107-112
• /
• 2011

Multiple ground rods are commonly used to obtain the low ground impedance, but they will not reduce the ground impedance unless the spacings between the ground rods are sufficient. This paper presents the experimental results of frequency-dependent resultant ground impedance of two ground rods in parallel. The resultant ground impedance of two ground rods in parallel were measured as functions of the spacing and length of ground rods and the frequency of test currents and were discussed based on the potential interferences. As a consequence, the frequency-dependent ground impedance of single ground rod and two combined ground rods give capacitive. It was found that the effect of potential interference on the ground impedance is directly associated with the frequency-dependent ground impedance and is strong in low frequency. Also, in order to reduce the increasing rate of resultant ground impedance of two ground rods due to potential interference to within 10(%), two ground rods in parallel will be placed over one rod length apart.

• Korean Journal of Cognitive Science
• /
• v.20 no.4
• /
• pp.421-437
• /
• 2009

A chatting system is a computer program that simulates conversations between a human and a computer using natural language. In this paper, we propose a statistical model to generate natural chatting sentences when keywords and speech acts are input. The proposed model first finds Eojeols (Korean spacing units) including input keywords from a corpus, and generate sentence candidates by using appearance information and syntactic information of Eojeols surrounding the found Eojeols. Then, the proposed model selects one among the sentence candidates by using a language model based on speech act information, co-occurrence information between Eojeols, and syntactic information of each Eojeol. In the experiment, the proposed model showed the better correct sentence generation rate of 86.2% than a previous conventional model based on a simple language model.

• Journal of Korea Foundry Society
• /
• v.22 no.4
• /
• pp.174-183
• /
• 2002

Twin-roll process is a relatively new continuous casting process which can produce high-quality strip products directly, and solidification rate can reach $10^3$ to $10^4$ K/s, leading to fine and uniform microstructures with enhanced mechanical properties. The strip casting condition for producing fine Al-Sn alloy strip was obtained experimentally, and defects appearing on the strip was examined. Crack formation and surface quality of the strip was found to depend mainly on process parameters such as melt temperature, roller gap and rolling speed. Sn structure of network type was observed in Al-20Sn and Al-40Sn alloy strips, and cell spacing of Al-40Sn alloy was smaller than that of Al-20Sn. Banding strength of the heat treated specimens increased with increasing of soaking time and temperature, and bonding strength of Al-20Sn alloy was more superior than that of Al-40Sn alloy. However wear resistance of Al-40Sn alloy contained large amount of soft Sn which possess good anti-friction characteristics was superior than that of Al-20Sn alloy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.29-32
• /
• 1998

A new treatment of LiV$_3$O$_{8}$ has beer proposed for improving its electrochemical behavior as a cathode material secondary lithium batteries. Early in its development, the preparation method of LiV$_3$O$_{8}$ strongly influenced its electrochemical properties, such as discharge capacity, rate capability and cycling efficiency. In the present experiment, a new synthesis route has been applied to obtain LiV$_3$O$_{8}$ . Instead of the conventional high temperature technique leading to the crystalline form, a solution technique producing the amorphous form has been used. This material, after dehydration, shows an electrochemical performance exceeding that of the crystalline one. These measurements showed that the ultrasonic treatment process of crystalline LiV$_3$O$_{8}$ causes a decrease in crystallinity and considerable increases in specific surface area and interlayer spacing. So the ultrasonic method provides a convenient means for improving the electrochemical behavior of LiV$_3$O$_{8}$ as a cathode material for secondary lithium batteries.batteries.