• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.170-174
• /
• 2008

Recently, a problem related to the thermal management in portable electronic and telecommunication devices is becoming issued. That is due to the trend of slimness of the devices, so it is not easy to find the optimal thermal management technology for the devices. From now on, a pressed circular type cooling device has been mainly used, however the cooling device with thin thickness is becoming needed by the inner space constraint. In the present study, the silicon and metal flat plate type cooling device with the separated vapor and liquid flow path was designed and fabricated. Through the experimental study, the normal isothermal characteristic by vapor-liquid phase change was confirmed and the cooling device with 70mm of total length showed 6.8W of the heat transfer rate within the range of $4{\sim}5^{\circ}C$/W of thermal resistance. In the meantime, the metal cooling device was developed for commercialization. The device was designed to have all structures of evaporator, vapor flow path, liquid flow path and condenser in one plate. And an envelope of that could be completed by combining the two plates of same structure and size. And the simplicity of fabrication process and reduction of manufacturing cost could be accomplished by using the stamping technology for fabricating large flow paths relatively. In the future, it will be possible to develop the commercialized cooling device by revising the fabrication process and enhancing the thermal performance of that.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4666-4672
• /
• 2011

Performance of NOx removal in SCR(Selective Catalytic Reduction) process depends on such various factors as catalyst factors (catalyst composition, catalyst form, space velocity, etc.), temperature of exhaust gas, and velocity distribution of exhaust gas. Especially the flow uniformity of gas stream flowing into the catalyst layer is believed to be the most important factor to influence the performance. In this research, the flow characteristics of a SCR process at design stage was simulated, using 3-dimensional numerical analysis method, to confirm the uniformity of the gas stream. In addition, the effects of guide vanes, baffles, and perforated plates on the flow uniformity for the inside and catalyst layer of the reactor were studied in order to optimize the flow uniformity inside the SCR reactor. It was found that the installation of a guide vane at the inlet duct L-tube part and the installation of a baffle at the upper part is very effective in avoiding chaneling inside the reactor. It was also found that additional installation of a perforated plate at the lower part of the potential catalyst layer buffers once more the flow for very uniform distribution of the gas stream.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.761-768
• /
• 2013

New warheads are designed and developed to be highly lethal when used as part of ballistic missile payloads. There are many trades associated with the design of a central warhead core, mainly dealing with the projectiles or penetrators. Obviously, a payload-type configuration is very susceptible to kills from one projectile because of the high impacts required for bomblet or submunition payloads. Based on these requirements, the optimum kill vehicle configuration will have the smallest mass and relative velocity that will kill all the submunitions. The designs of the penetrator shape and size are directly related to the space and weight of the warhead. The shape, size, L/D, penetrator material, and manner in which they are inserted inside the surrounding explosive segments are critical in achieving successful penetrator design. The AUTODYN-3D code was used to study the effect of penetrator penetration. The objective of numerical analysis was to determine the penetration characteristics of the penetrator produced by hypervelocity impacts under different initial conditions such as initial velocity, shape, and L/D of the penetrator.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3A
• /
• pp.189-198
• /
• 2011

Although high strength bolts with tensile strength of 1,000 MPa are mainly used in steel structure construction sites throughout the world, new high strength bolts are required owing to the installation of continuous long-span bridges resulting from the development and distribution of high strength steel and ultra-thick steel plates. Currently, high strength bolts with tensile strength of 1,300 MPa are being used. However, as they tend to place a large load on a small section of space, a high strength bolt of high structural performance and screw thread shape with less stress concentration is thought to be more effective. This study conducted analyses in order to develop an improved screw thread shape relative to the KS screw thread shape. A new screw thread shape with less stress concentration and effective load distribution at the time of fastening bolts and nuts was provided upon analysis of the characteristics of screw thread shape. Additionally, in an experimental study, the structural performance of high strength bolts with tensile strength of 1,300 MPa was investigated. The results revealed that the new screw thread shape was more effective than the existing screw thread shape in terms of structural performance and mitigating the stress concentration.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.1-33
• /
• 1997

The objective of this study was to analyze the in vitro and in vivo corrosion products of low and high copper amalgams. The four different types of amalgam alloy used in this study were Fine cut, Caulk spherical, Dispersalloy, and Tytin. After each amalgam alloy and Hg were triturated according to the directions of the manufacturer by means of the mechanical amalgamator(Amalgam mixer. Shinhung Co. Korea), the triturated mass was inserted into a cylindrical metal mold which was 12mm in diameter and 10mm in height. The mass was condensed by 150Kg/cm compressive force. The specimen was removed from the mold and aged at room temperature for about seven days. The standard surface preparation was routinely carried out by emery paper polishing under running water. In vitro amalgam specimens were potentiostatically polarized ten times in a normal saline solution at $37^{\circ}C$(potentiostat : HA-301. Hukuto Denko Corp. Japan). Each specimen was subjected to anodic polarization scan within the potential range -1700mV to+400mV(SCE). After corrosion tests, anodic polarization curves and corrosion potentials were obtained. The amount of component elements dissolved from amalgams into solution was measured three times by ICP AES(Inductive Coupled Plasma Atomic Emission Spectrometry: Plasma 40. Perkim Elmer Co. U.S.A.). The four different types of amalgam were filled in occlusal and buccal class I cavities of four human 3rd molars. After about five years the restorations were carefully removed after tooth extraction to preserve the structural details including the deteriorated margins. The occlusal surface, amalgam-tooth interface and the fractured surface of in vivo amalgam corrosion products were analyzed. In vivo and in vitro amalgam specimens were examined and analyzed metallographically by SEM(Scanning Electron Microscope: JSM 840. Jeol Co. Japan) and EDAX(Energy Dispersive Micro X-ray Analyser: JSM 840. Jeol Co. Japan). 1. The following results are obtained from in vitro corrosion tests. 1) Corrosion potentials of all amalgams became more noble after ten times passing through the in vitro corrosion test compared to first time. 2) After times through the test, released Cu concentration in saline solution was almost equal but highest in Fine cut. Ag and Hg ion concentration was highest in Caulk spherical and Sn was highest in Dispersalloy. 3) Analyses of surface corrosion products in vitro reveal the following results. a)The corroded surface of Caulk spherical has Na-Sn-Cl containing clusters of $5{\mu}m$ needle-like crystals and oval shapes of Sn-Cl phase, polyhedral Sn oxide phase. b)In Fine cut, there appeared to be a large Sn containing phase, surrounded by many Cu-Sn phases of $1{\mu}m$ granular shapes. c)Dispersalloy was covered by a thick reticular layer which contained Zn-Cl phase. d)In Tytin, a very thin, corroded layer had formed with irregularly growing Sn-Cl phases that looked like a stack of plates. 2. The following results are obtained by an analysis of in vivo amalgam corrosion products. 1) Occlusal surfaces of all amalgams were covered by thick amorphous layers containing Ca-P elements which were abraded by occlusal force. 2) In tooth-amalgam interface, Ca-P containing products were examined in all amalgams but were most clearly seen in low copper amalgams. 3) Sn oxide appeared as a polyhedral shape in internal space in Caulk spherical and Fine cut. 4) Apical pyramidal shaped Sn oxide and curved plate-like Sn-Cl phases resulted in Dispersalloy. 5) In Tytin, Sn oxide and Sn hydroxide were not seen but polyhedral Ag-Hg phase crystal appeared in internal space which assumed a ${\beta}_l$ phase.

• The korean journal of orthodontics
• /
• v.26 no.2 s.55
• /
• pp.153-162
• /
• 1996

Rapid maxillary expansion is widely used for the correction of anteroposterior discrepancies, constriction of the maxillary arch, etc. This experiment was undertaken to examine the serial changes in the osteogenesis as well as the collagen fiber bundles in the intermaxillary suture during the rapid maxillary expansion treatment. Four young female dogs aged 6 to 8 months old and not showing menarche yet were used for the experiment. The maxillary impression of dogs were taken, expansion device cast and Hyrax screw soldered at the midline in the 1st premolar area. RME device was delivered to the dogs and the activation of 0.25 mm per quarter-turn was done 2 times per day for 10 days until 5 mm separation was made. Separation of the maxilla was confirmed by X-ray. The animals were sacrificed on 0, 15, 30, 60 days from the finish of maxillary separation and preparations for light microscopy and surface electron microscopy were made. The sutures were cut into frontal serial sections for examination of the histological reactions. The following results were obtained and the conclusions made. 1. The edges of the two palatal plates bordering the midpalatal suture which at the beginning of the retention period were mainly composed of compact bone, underwent extensive resorption followed by new bone formation and gradually became spongy bone rich in bone marrow which in the 60 day retention animal became the compact bone with short intermaxillary suture space. During this transformation, newly formed trabecular bone tissues were added to the original margin. 2. Throughout the expansion period, the collagen fibers underwent successive changes such as stretching, loss of polarity, and finally fibrillogenesis. Towards the end of the expansion procedure, sharpey's fiber formation in newly formed bones were observed. 3. Bony spicules were found in the initial stage of retention on occlusal topographic X-rays, which later were confirmed to have ossified. 4. Judging from the histological changes occuring during the experimental expansion, excessive expansion will cause an excessive bleeding, and retard the remodeling of intermaxillary suture. According to the above results, the bone remodeling after rapid maxillary expansion was preceded by the migration of migratory cells into the intermaxillary suture area. The bone remodeling phenomena were on-going during the 2 months retention sample.

• Korean Journal of Construction Engineering and Management
• /
• v.5 no.5 s.21
• /
• pp.183-192
• /
• 2004

Even in Korea the number of steel structure buildings that allow internal space and easy change of their layouts in accordance with the purpose of buildings and box-type steel bridges constructed with thick plates with thickness in a rage just from a few $\beta$AE to \$100\beta$AE is increasing these days and therefore, domestic fabrication and processing technology of members for steel structures is being improved at a pace faster than in the past to meet the growing requirements of consumers for high reliability on quality control on the related steel structures. However, most domestic fabricators os steel structures who are turning out their steel products in accordance with the designs prepared by engineering companies in their respective works for the sake of cost cut more than anything else, hesitating to introduce any advanced new technology into themselves. In the case of the steel structure design application for small and mid-size buildings in particular, it is quite meaningful not only for those who are involved in steel structure business, but also for the people working at construction work fields to review the result of the study on the connections of steel structure members deigned to obtain superb quality of steel structures within short period for steel fabrication and erection at fields in economical ways, as there is a glowing tendency seeking standardization of connection of steel structure members as well as whole structure together with the development on design of construction system of buildings including their exterior and interior decoration materials, manufacture of the related members and fabrication technique structure. This paper has been prepared with the aim to review the peculiar characteristics of buildings constructed with the main frames of steel structures and actual cases of the change made ing the connections between steel structure columns and between columns and girder members in order to reduce the work period necessary for fabrication and erection of steel structures at the maximum as well as the some examples of steel structures fabricated through automatic welding by robots for box-type columns in addition to the description of the problems found in the course of fabricating those steel structures, suggesting possible counter-measures to solve them.

• Journal of Forest and Environmental Science
• /
• v.21 no.1
• /
• pp.34-58
• /
• 2005

This study was executed to find out how to improve the planting and use of landscaping plants in Weonju and Hoengseong. 1. The number of street trees were 22,068 and the species number were 10 species in Weonju in 2004. The major species of street trees were Ginkgo biloba(58%), Prunus sargentii(15%), Zelkova serrata(9%), Prunus armeniaca var. ansu(8%), and Acer palmatum(6%). The ratio of native species versus exotic were 50:50. In Hoengseong, the number of street trees was 13,500 and the species number were 15 species. The major species of street trees were Prunus sargentii(42%), Ginkgo biloba(23%), Acer triflorum(12%), Prunus armeniaca var. ansu(6%), and Prunus mume(4%). The ratio of native species versus exotic were 67:33. The species of which planting frequency within two areas was very high were Ginkgo biloba and Prunus sargentii. 2. It is necessary to select tree species suitable for the characteristics of the locality and to raise distinctive street trees that contribute to the tourist industry. For the purpose, the appropriate street trees in two areas are Cornus controversa, Quercus aliena, Zelkova serrata, Prunus padus, Sorbus alnifolia, Sorbus comixta, Albizzia julibrissin, Acer triflorum, Styrax japonica, Chionanthus retusus, Celtis sinensis, Prunus yedoensis, Malus sieboldii, Crataegus Pinnatifida, Prunus armeniaca var. ansu and Pyrus pyrifolia etc.. 3. Appropriate pruning adds to the aesthetic and prolongs the useful life, it also requires less managing of insects and diseases to maintain good healthy of street trees. Street trees were not properly pruned due to electric lines and shortage of pruning information. The pruning was controlled by Korea Electric Power Co, which has no pruning information. Pruning must be maintained by a professional landscape company to maintain good shape such as with Bonsai. The shrubs planting zone between street trees and other trees, and preservation plates were established for healthy of street trees. They have to be repaired and maintained well to keep better environmental conditions. The proper fertilization, the control of pests and diseases, the installation of drainpipe and the use of soil brought from another place were needed to improve the planting, use and maintenance of landscape plants. 4. The species number of school trees and flowers of 102 schools in Weonju and Hoengseong were 17species, 16species respectively. The major species of school trees in Weonju were Juniperus chinensis(24%), Ginkgo biloba(17%), Pinus densiflora(14%), Zelkova serrata(14%), and Pinus koraiensis(9%), and those of school trees in Hoengseong were Pinus koraiensis(44%), Abies holophylla(25%), Juniperus chinensis(8%), and Ginkgo biloba(8%). The major species of school flowers in Weonju were Rosa centifolia(47%), Forsythia koreana(24%), Magnolia kobus(12%), and Rhododendron schlippenbachii(6%), and those of school flowers in Hoengseong were Forsythia koreana(36%), Rhododendron schlippenbachii(33%), Magnolia kobus(6%) and Dicentra spectabilis(6%). 5. The species number of the protection trees designated by Woenju and Hoengseong were 15 species. The major species of protection trees were Zelkova serrata(100 trees), Ginkgo biloba(18) Pinus densiflora(7), Quercus spp. (5), Juniperus chinensis(4) and Alnus japonica(4). 6. The landscape plants planted around 2004 in weonju were Prunus yedoensis(2,563 trees), Betula platyphylla var. japonica(2,000), Abies holophylla(1,785), Diospyros kaki(1,100), Prunus sargentii(880) and Prunus armeniaca var. ansu(708) etc.. The shrubs planted were Rhododendron obutusum(21,559 plants), Rosa centifolia (7,150), Rhododendron yedoense var. poukhanense(5,950), Forsythia koreana(3,000) and Ligustrum obtusi[olium(2,500) etc.. The landscape plants planted in Hoengseong Acer triflorum(928trees), Prunus yedoensis(455), Zelkova serrata(327), Thuja orientalis(261), Prunus sargentii(257), Pinus koraiensis(200), Prunus persica for. rubro-plena(200) and Pyrus pyrifolia (200) etc.. The shrubs planted were Rhododendron yedoense var. poukhanense(15,936), Syringa dilatata(10,090), Forsythia koreana(9,660), Cercis chinensis(3,200), Buxus microphylla var. koreana(2,600) and Rosa centifolia(1,868) etc.. 7. The species numbers of the herbaceous plants planted in 2004 in Weonju were 24 species and the ratio of native species versus exotic were 7:17. The major species of perennial plants were Aster koraiensis(30,656 plants), Coreopsis drummondii(7,656), Rudbeckia bicolor(6,000), Chrysanthemum morifolium(4,850) and Chrysanthemum zawadskii var. latilobum(4,312). The major species of annuals and biennials were Cosmos bipinnatus(672,000 plants), Zinnia elegans(35,600), Petunia hybrida(26,920), Viola tricolor(23,000), Helianthus annuus(17,000), and Geranium cinereum var. pubcaulescens(5,200). In Hoengseong, the numbers of herbaceous plants were 906,310 plants and the species numbers were 15 species. The major species of perennials plants were Aster koraiensis(70,480 plants), Hemerocallis fulva(20,070), and Phlox drummondii(18,000). The major species of annuals and biennials were Phlox hybrida(174,000 plants), Cosmos bipinnatus(125,000), Zinnia elegans(109,000), Tagetes patula(96,700), Vinca rosea(89,000) and Calendula officinalis(70,000). 8. Through these result, it was thought that the diversification of planting species, the selection of plants suitable to each space and the generalization of use of native species were needed.