• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.7 no.1
• /
• pp.23-31
• /
• 2007

In this paper, UWB system did research about effect that interference effect with neighborhood single equipment or group equipment gets in broadcasting communication service. For this, 2.6425GHz SDMB(Satellite Digital Multimedia Broadcasting) that a special of electric wave interference is near frequency-band including interference of signal by unnecessary radiation level that is radiated in UWB system, and degree of 3.4125GHz broadcasting relay net that is In-band frequency-band and interference effect that get in service analyzed comparison and, modulation of broadcasting relay net and interference measurement equipment used Impulse and OFDM methods. Impulse method was $BER\;=\;1{\times}\;10^{-4}$ that broadcasting signal receiption is possible at 1.4m point because interference effect happens from 2m point in SDMB system, and it was $BER\;=\;1{\times}\;10^{-4}$ that OFDM method receives interference effect from 0.8m point and broadcasting signal receiption is possible at 0.5m point. Also, about Gap-Filler center frequency, In case of space interval more than 0.01m, there was no interference effect. Therefore, for the electric wave of UWB system that is small output applies to system without interference effect in broadcasting communication service, confirmed that UWB system of OFDM method is less interference effect than UWB system of Impulse method.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.4
• /
• pp.11-19
• /
• 2015

The important properties of EVA (ethylene vinyl acetate) redispersible polymer was waterproof, densification of internal pore space of concrete and ball bearing and micro filler. Also, the significant role of polypropylene(PP) fiber was crack control and blockade of movement for deterioration factors. The most studies for EVA were limited in the field of mortar and PP fiber reinforced concrete had been studied in the state of being restricted unit water content, rich mix and mixing much of the fiber without considering construction site. Therefore, the control mix design were applied in ready mixed concrete using 10 % fly ash of total cement weight used in batch plant. On the basis of control mix design, EVA contents ranging from 0 % to 10 % of total cement weight and PP fiber contents ranging from 0 % to 0.5 % of EVA concrete volume were used in the mix designs. The results showed the maximum compressive strength value was measured at EVA 5.0 % and PP fiber 0.1 %, the minimum water absorption ratio was at EVA 10 % and PP fiber 0 %, the durability factor for freezing and thawing resistance was at EVA 5.0 % and PP fiber 0.3 % and the minimum weight reduction ratio of resistance to sulfuric acid attack was at EVA 10 % and PP fiber 0.5 % after curing age 42days. Meanwhile, From these results, PP fiber reinforced EVA concrete would be very benefit, if each optimal mix types were used in hydraulic structures, underground utilities and agricultural structures.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.27 no.3
• /
• pp.238-247
• /
• 2005

The placement of different graft materials and/or the use of occlusive membranes to cover the extraction socket entrance are techniques aimed at reducing alveolar ridge resorption and enhancing bone formation. However, in spite of its clinical advantage, the use of graft materials in fresh extraction socket has been questioned because particles of the grafted material have been found in alveolar sockets with fibrous union. The purposes of this study were to evaluate whether alveolar ridge resorption following tooth extraction could be reduced and bone formation could be enhanced by the application of absorbable gelatin spongy or gelatin spongy soaked with platelet rich plasma(PRP) used as a space filler in clinical and radiographic aspects. Eighty patients who were scheduled for extraction of both third molars were participated and carried out by one experienced surgeon. Following extraction of teeth, one extracted socket were treated with gelatin spongy as an experimental group A and the other were treated with gelatin spongy and PRP as an experimental group B. The routine extracted socket were healed without any treatment as a control group. From the period of extraction to 12 weeks postoperatively, we examined the clinical course and radiographic evaluation on socket at regular interval. Both experimental groups showed faster wound healing process than control clinically. Vertical gingival height of the extraction socket were less changed statistically in both experimental groups than control. The horizontal width change of the extraction socket were not significant statistically in any group. Radiographic changes of the alveolar bone height were less changed in both experimental groups and bone density were showed higher than control. There were a little difference between experimental group A and B. In conclusion, absorbable gelatin sponge and with PRP were considered as having preservation effects of extraction socket and stimulation of bone formation process after extraction.

• Polymer(Korea)
• /
• v.24 no.4
• /
• pp.571-577
• /
• 2000

A new type of filler for epoxy-clay nanocomposites has been prepared by the reaction of octadecyltrimethylammonium bromide and layered sodium montmorillonite (MMT) via an ion-exchange reaction. The gallery space was further modified by grafting the aminopropyl groups via a reaction between a octadecyltrimethylammonium-MMT and 3-aminopropyltriethoxysilane (APS). The interlayer modification of MMT was confirmed by XRD, IR, and solid-state $^{29}$ Si CP/MAS NMR. Furthermore, clay-polymer nanocomposites have been synthesized by the polymerization of diglycidyl ether of bisphenol A(DGEBA) and $C_{18}$ H$_{37}$ N($CH_3$)$_3$-APS-MMT. The resulting hybrid nanocomposites were characterized by XRD, transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The results proved that the organomontmorillonite could be exfoliated and uniformly dispersed in the epoxy matrix.

• Journal of Korean Neurosurgical Society
• /
• v.40 no.2
• /
• pp.90-94
• /
• 2006

Objective : Acute vertebral burst fractures warrant extensive fixation and fusion on the spine. Osteoplasty [vertebroplasty with high density resin without vertebral expansion] has been used to treat osteoporotic vertebral compression fractures. We report our experiences with osteoplasty in acute vertebral burst fractures. Methods : Twenty-eight cases of acute vertebral burst fracture were operated with osteoplasty. Eighteen patients had osteoporosis concurrently. Preoperative MRI was performed in all cases to find fracture level and to evaluate the severity of injury. Preoperative CT revealed burst fracture in the series. The patients with severe ligament injury or spinal canal compromise were excluded from indication. Osteoplasty was performed under local anesthesia and high density polymethylmethacrylate[PMMA] was injected carefully avoiding cement leakage into spinal canal. The procedure was performed unilaterally in 21 cases and bilaterally in 7 cases. The patients were allowed to ambulate right after surgery. Most patients discharged within 5 days and followed up at least 6 months. Results : There were 12 men and 16 women with average age of 45.3[28-82]. Five patients had 2 level fractures and 2 patients had 3 level fractures. The average injection volume was 5.6cc per level Average VAS [Visual Analogue Scale] improved 26mm after surgery. The immediate postoperative X-ray showed 2 cases of filler spillage into spinal canal and 4 cases of leakage into the retroperitoneal space. One patient with intraspinal leakage was underwent the laminectomy to remove the resin. Conclusion : Osteoplasty is a safe and new treatment option in the burst fractures. Osteoplasty with minimally invasive technique reduced the hospital stay and recovery time in vertebral fracture patients.

• Journal of Periodontal and Implant Science
• /
• v.35 no.2
• /
• pp.491-510
• /
• 2005

This study was performed to evaluate the effect of inorganic polyphosphate on bone formation in the calvaria of rabbit in the procedure of guided bone regeneration with bovine cancellous bone graft and titanium reinforced expanded polytetrafluoroethylene(TR-ePTFE) membrane. The rabbits were divided into four groups. Control group I used only TR-ePTFE membrane, control group II used TR-ePTFE membrane and deproteinized bovine bone mineral soaked in saline, experimental group III and IV used TR-ePTFE membrane and deproteinized bovine bone mineral soaked in 1% or 2% inorganic polyphosphate respectively. After decortication in the calvaria, GBR procedure was performed on 12 rabbits with titanium reinforced ePTFE membrane filled with deproteinized bovine bone mineral soaked in saline or inorganic polyphosphate. The animals were sacrificed at 2 weeks, 4 weeks, and 8 weeks after the surgery. Decalcified and non-decalcified specimens were processed for histologic and immunohistochemistric analysis. 1. Titanium reinforced ePTFE(TR-ePTFE) membrane showed good spacemaking and cell occlusiveness capability, but it showed poor wound stabilization. 2. The deproteinized bovine bone mineral did not promote bone regeneration, but it acted as a space filler. 3. There was no complete resorption of the deproteinized bovine bone mineral within 8 weeks. 4. 1% inorganic polyphosphate did not promote bone formation, but 2% inorganic polyphosphate promoted bone formation. Within the above results, 2% inorganic polyphosphate could be used effectively for bone regeneration.

• Tunnel and Underground Space
• /
• v.24 no.6
• /
• pp.405-417
• /
• 2014

In a high-level waste repository, the gap fill of the engineered barrier is an important component that influences the performance of the buffer and backfill. This paper reviewed the overseas status of R&D on the gap fill used engineered barriers, through which the concept of the gap fill, manufacturing techniques, pellet-molding characteristics, and emplacement techniques were summarized. The concept of a gap fill differs for each country depending on its disposal type and concept. Bentonite has been considered a major material of a gap fill, and clay as an inert filler. Gap fill was used in the form of pellets, granules, or a pellet-granule blend. Pellets are manufactured through one of the following techniques: static compaction, roller compression, or extrusion-cutting. Among these techniques, countries have focused on developing advanced technologies of roller compression and extrusion-cutting techniques for industrial pellet production. The dry density and integrity of the pellet are sensitive to water content, constituent material, manufacturing technique, and pellet size, and are less sensitive to the pressure applied during the manufacturing. For the emplacement of the gap fill, pouring, pouring and tamping, and pouring with vibration techniques were used in the buffer gap of the vertical deposition hole; blowing through the use of shotcrete technology and auger placement and compaction techniques have been used in the gap of horizontal deposition hole and tunnel. However, these emplacement techniques are still technically at the beginning stage, and thus additional research and development are expected to be needed.

• Journal of the Korea Concrete Institute
• /
• v.22 no.3
• /
• pp.287-295
• /
• 2010

In this study, ordinary Portland cement was used and the air void was minimized by using minute quartz as the filler. In addition, steel fibers were used to mitigate the brittle failure problem associated with high strength concrete. This study is in progress to make an Ultra-high strength powdered concrete (UHSPC) which has compressive strength over 300 MPa. To increase the strength of concrete, we have compared and analyzed the compressive strengths of the concretes with different mix proportions and curing conditions by selecting quartz sand, dolomite, bauxite, ferro silicon which have diameters less than 0.6 mm and can increase the bond strength of the transition zone. Ultra-high strength powdered concrete, which is different from conventional concrete, is highly influenced by the materials in the mix. In the study, the highest compressive strength of the powdered concrete was obtained when it is prepared with ferro silicon, followed in order by Bauxite, Dolomite, and Quartz sand. The amount of ferro silicon, when the highest strength was obtained, was 110%, of the weight of the cement. SEM analysis of the UHSPC showed that significant formation of C-S-H and Tobermorite due to high temperature and pressure curing. Production of Ultrahigh strength powdered concrete which has 28-day compressive strength upto 341MPa has been successfully achieved by the following factors; steel fiber reinforcement, fine particled aggregates, and the filling powder to minimize the void space, and the reactive materials.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.5 no.4
• /
• pp.1-9
• /
• 2002

This study is carried out to make the environmentally affinitive porous planting block for revegetation and to make a effective program for greening plans. The summary is shown below. 1. In order to get stronger intensity and distribute proper porosity in the block for planting, the cements mixed with fine soil were used and the finer in soil grains gives the stronger in intensity of the cements. Use of the furnace slag cements instead of the portland cements showed relatively stronger in intensity of the block. The intensity of the block became stronger when the mixed ratio of the cements to soil is 5 : 1, but the pore space ratio was lower. The percolate pH of the portland cements after one month of treatment was 13.1 but the percolate pH of the furnace slag cements was shown lower. To mold proper porous planting blocks, the proper combination of additives such as the dehydrating agent, elastic agent and adhesives into the mixture of cements and soil gives better effectives. 2. After molding the porous planting blocks, it gave a better result when the grains of the filler made of peat moss, upland soil and compound fertilizer were smaller than 2 mm in size. Shaking of the filling materials also gave the better result, but it took more time and cost much more. Therefore, it was better when the filling materials were mixed with water first then flew down for stuffing. 3. It was necessary to cover with soil after seeding or planting on the porous planting blocks. The proper thickness of the soil to help root development and keep moisture is about 3~5 cm. 4. The plants for planting on the porous planting block were required stronger in the growth condition of their roots and their environmental adaptability. The average germination percentage and rate of Platycodon grandiflorum on the porous planting block were 88.8% and 85% accordingly and their rate is very uniform. The germination rates of Dianthus superbus var. longicalycinus and Taraxacum officinale were more than 50%. These grass species, Chelidonium majus var. asiaticum, Lysimachia mauritiana and Scabiosa mansenensis were the suggested biennial grasses in the planting area where exchanging of the seedling or nursery plants was not necessary because their germination rates were 59.3, 45.6 and 40.3% accordingly. Viola kapsanensis, Chrysanthemum sp., Taraxacum sp. and Iris ensata var. spontanea are the grass species that could be used by seeding for greening. However, the germination rate of Solidago virga-aurea var. asiatica, Aster scaber and Lythrum anceps were lower than 10%. The coverage ratio of Ixeris stolonifera is more than 80% after 60 days seeding and the root length of most of species are more than 10 cm except Iris ensata var. spontanea and Platycodon grandiflorum because their root developed thicker than other species.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.29 no.6
• /
• pp.467-473
• /
• 2007

The most important factor for successful implantation is osseointegration between the implant and bone. The expression of bone morphogenetic proteins (BMPs) inducing bone formation would differ after maxillary sinus elevation. And within the same graft material. the expression of BMPs would change with time after graft. The aim of this study was to compare the relative expressions of BMP4 and BMP6 using real-time RT-PCR when maxillary sinus elevation was performed using deproteinated bovine bone powder (DBBP) as the graft material or absorbable gelatin sponge (AGS) as the filler without any graft material. Fifteen rabbits, each weighing between 3.0 to 3.5 Kg, were divided randomly into 5 groups of 3 animals each based on their time of sacrifice 0, 3, 5, 7 and 9 days). After exposure of the maxillary sinus bilaterally, bone graft was performed in the right maxillary sinus using DBBP ($BBP^{(R)}$ Oct Inc., Cheonan, Korea) and only AGS ($Gelfoam^{(R)}$ Pharmacia & Upjohn Company, Kalamazoo, MI, U.S.A) was placed into the left without any graft material. Each group of rabbits was sacrificed at 1, 3, 5, 7, or 9 days after operation and all specimens were harvested. And the following results were obtained using real-time RT-PCR from isolated total RNA of the samples. 1. The expression of BMP4 increased at postoperative 1 and 3 days in both DBBP group and AGS group. In AGS group. it decreased at postoperative 5 days. increased again at postoperative 7 days, and decreased at postoperative 9 days. In DBBP group, it increased until postoperative 7 days and decreased at postoperative 9 days. Although the expression of BMP4 was higher in DBBP group compared with AGS group, it was not statistically significant (p>0.05). 2. The expression of BMP6 increased at postoperative 1 and 3 days in both DBBP group and AGS group. In AGS group, it decreased at postoperative 5 days, increased again at postoperative 7 days, and decreased at postoperative 9 days. In DBBP group, it increased until postoperative 7 days and decreased at postoperative 9 days. Although the expression of BMP6 was higher in AGS group compared with DBBP group, it was not statistically significant (p>0.05). 3. There was no statistically significant difference in BMP expression in both groups during same period of time. It' s probably because DBBP and AGS both functioned as a space retainer so that the BMP expression in blood clot seemed to be similar. 4. Thus, DBBP would not offer many benefits for early bone regeneration compared with AGS. The expression of BMP in early bone formation seems to be more influenced by physical carrier rather than the graft type.