• Journal of Advanced Marine Engineering and Technology
• /
• 제24권1호
• /
• pp.119-126
• /
• 2000

In constructing the positioning system based on a conventional dead-reckoning for a wheeled vehicle with pneumatic tires, the position estimation error is inevitable as changes of the radius of the wheels depend on live load and variable enviroment. Therefore, this paper proposes the positioning system which can estimate the error source i.e. the vehicle parameter errors, such as the right and left wheel radius error, using gyroscope and ultrasonic sensor and correct the parameter to reduce the dead-reckoned position estimation error. The extended Kalman filter was used as a method for the multisensor data fusion. The simulation to verify the effectiveness of the proposed positioning system is performed.

• Journal of Positioning, Navigation, and Timing
• /
• 제11권4호
• /
• pp.251-261
• /
• 2022

The Centimeter Level Augmentation Service (CLAS) is the Precise Point Positioning (PPP) - Real Time Kinematic (RTK) correction service utilizing the Quasi-Zenith Satellite System (QZSS) L6 (1278.65 MHz) signal to broadcast the Global Navigation Satellite System (GNSS) error corrections. Compact State-Space Representation (CSSR) corrections for mitigating GNSS measurement error sources such as satellite orbit, clock, code and phase biases, tropospheric error, ionospheric error are estimated from the ground segment of QZSS CLAS using the code and carrier-phase measurements collected in the Japan's GNSS Earth Observation Network (GEONET). Since the CLAS service begun on November 1, 2018, users with dedicated receivers can perform cm-level precise positioning using CSSR corrections. In this paper, CLAS-based VRS-RTK performance evaluation was performed using Global Positioning System (GPS) observables collected from the refence station, TSK2, located in Japan. As a result of performing GPS-only RTK positioning using the open-source software CLASLIB and RTKLIB, it took about 15 minutes to resolve the carrier-phase ambiguities, and the RTK fix rate was only about 41%. Also, the Root Mean Squares (RMS) values of position errors (fixed only) are about 4cm horizontally and 7 cm vertically.

• 대한디지털의료영상학회논문지
• /
• 제10권2호
• /
• pp.17-22
• /
• 2008

It is to improve customer satisfaction measurement and CT Scan process without delay of examination time when is using Scan positioning time(Planning time) that time is happened always between research reactor CT examination to increase fear and examination satisfaction by the customer's comprehension tribe which get the latest contrast enhancement CT examination. Needs and interests that customer wants to compose visual and auditory Contents to be played to Scan positioning time did questionnaire about curiosity later before CT examination to 600 people for October - November 2 months of 2006 to customer whole that get CT examination on source. Data getting through questionnaire investigated examination comprehension and satisfaction through questionnaire after experiment Scan Positioning to 500 coming to help customers to be source CT examination for 3 months February December - 2007 year in 2006 manufacturing Voice and Visual announce media for reference. To customer who interest degree appeared, and answers preparatory audit from preparatory audit about curiosity of CT examination customer to order of examination time required(43%), contrast media side effect(26%), examination region(20%), breath(10%), etc..(1.5%) audio-visual materials in questionnaire that attain after do reclamation among examination age, sex, reception type of irrelatively in 91% of target increase of hailing degree and examination satisfaction appear. Searched that customer hailing and satisfaction are increased greatly when use of audio-visual materials in satisfaction result that use CT Positioning delay time. In experiment process, It took lacking part by method that use hearing in case of do not use sight as is unavoidable in subject position or old age. Through this, audio-visual materials could analogize that it is more useful method that use sight and hearing at the same time.

• Journal of Positioning, Navigation, and Timing
• /
• 제1권1호
• /
• pp.15-21
• /
• 2012

For a GNSS receiver's robustness against RFI and the high accuracy of navigation solution in GNSS, interference source detection and mitigation are needed. In this paper, an adaptive lattice IIR notch filter is employed to track single-tone continuous wave and swept continuous wave interference signals, and an interference detection method is proposed. Furthermore, this paper presents interference source characterization algorithm using multiple ground stations' interference detection results. The measurement of the signal powers from each ground station is used to build weighting factors to estimate the type of the interference. The performance of interference detection algorithm is simulated for scenarios of GPS signal in the presence of single-tone continuous wave interference and swept continuous wave interference.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제13권9호
• /
• pp.4541-4554
• /
• 2019

This paper proposes a planar projection DV-hop location algorithm (PTCDV-hop) based on the LED semi-angle at half power (SAHP, which accounts for LED SAHP characteristics in visible light communication (VLC)) and uses the DV-hop algorithm for range-free localization. Distances between source nodes and nodes positioned in three-dimensional indoor space are projected onto a two-dimensional plane to reduce complexity. Circles are structured by assigning source nodes (projected onto the horizontal plane of the assigned nodes) to be centers and the projection distances as radii. The proposed PTCDV-hop algorithm then determines the position of node location coordinates using the trilateral-weighted-centroid algorithm. Simulation results show localization errors of the proposed algorithm are on the order of magnitude of a millimeter when three sources are used. The PTCDV-hop algorithm has higher positioning accuracy and stronger dominance than the traditional DV-hop algorithm.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권5호
• /
• pp.15-21
• /
• 2003

In order to improve the quality of a spindle unit it is important to increase its rotational accuracy. The rotational accuracy of a spindle unit can be defined as the stability or immobility of its spindle axis while rotating. Spindle rotation in the rolling bearings causes the disturbing influence, which leads to the oscillation of a rotation axis. The purpose of this study is to investigate the oscillation sources and find a way to decrease the runout without additional expenses. The main source of oscillation is the interaction between rolling bodies and ring races. The first oscillation source was the out-of-shape imperfection of inner bearing ring. The mutual compensation of oscillation by proper rings orientation was proposed, which sometimes allow to decrease the radial runout of spindle rotation axis by approximate 40％ down. Also the outer ring harmonics were explored as the second oscillation source. The analysis shows the dependency between the number of rolling bodies and the outer ring race harmonics. The conclusion on the orientation of bearing cages and the bearing rings was made, which makes possible to obtain the optimal variant of their mounting in the spindle unit when the rotational accuracy of the spindle is maximal, and the spindle runout considerably less.

• 한국인터넷방송통신학회논문지
• /
• 제13권5호
• /
• pp.85-91
• /
• 2013

실내에서의 위치기반 서비스 및 상황인식 서비스를 위해서는 실내에서의 정밀한 위치인식 기술이 필수적이다. 신호원과 여러 개의 신호 수신기와의 거리 차이를 이용하여 신호원의 상대위치를 추정하는 TDOA(Time Difference of Arrival) 기술이 사용되고 있는데, 거리 차이 측정의 오차에 따른 위치 추정 오차가 발생하므로 이를 최소화하기 위한 연구가 많이 진행되어 왔다. 본 논문에서는 신호원과의 거리 차이값을 이용하여 계산된 여러 근중에서 실제의 근을 선별하고 이를 평균내어 신호원의 위치를 추정하는 알고리즘이 제안되었으며, 기존의 방법에 비해 오차가 개선되었다.

• 한국산업융합학회 논문집
• /
• 제13권2호
• /
• pp.85-92
• /
• 2010

This study shows the path generation algorithm for an UGV (Unmanned Ground Vehicle). The developed UGV frame which has a 4-wheel driven mechanism and diesel source is applied. Proposed vehicle system in this research is aimed to military purpose. To achieve the unmanned autonomous driving, following two main issues are considered. First, behavior module for positioning and posture of vehicle system and second, cognition module to receive the information from environment are proposed and verified. To do this, rover which can acquire the positioning information from earth coordinate and IMU (Inertial Measurement Unit) which can measure the posture are combined to design the path planning algorithm.

• 한국측량학회지
• /
• 제30권5호
• /
• pp.459-466
• /
• 2012

전리층에 의한 신호지연은 SA 해제이후 GPS 측위에 가장 큰 오차 요인이다. 전리층 오차는 이중주파수 수신기를 이용할 경우 무전리층 조합으로 쉽게 제거할 수 있지만 단일주파수 수신기는 무전리층 조합을 수행할 수 없기 때문에 전리층 오차를 쉽게 제거할 수 없다는 단점이 존재한다. 따라서 이 연구에서는 단일주파수 사용자를 위한 격자형 지역 전리층 모델을 개발하였다. 개발된 지역 전리층 모델을 평가하기 위해 IGS의 전지구 모델과 비교하였으며 그 결과 열흘 평균 3.8 TECU의 RMSE를 나타내었다. 그리고 측위 정확도에 미치는 영향을 평가하기 위해 생성된 지역 전리층 모델을 적용하여 L1 관측치만을 이용한 중 장기선 상대측위를 수행하였다. 전리층과 대류권 오차를 보정한 결과 두 오차를 보정하기 전의 측위 결과와 비교하여 평균 46.7%의 측위 정확도가 향상되었으며 대류권 오차만 보정한 측위 결과와 비교하여 전리층 오차 보정 후에는 평균 14.5%의 측위 정확도가 향상되었다.

• 전기학회논문지
• /
• 제58권2호
• /
• pp.415-421
• /
• 2009

TOA(time-of-arrival) and TDOA(time-difference-of-arrival) positioning techniques are commonly used in many radio-navigation systems. From the literature, it is known that the position estimate and error covariance matrix of TDOA obtained by GN(Gauss-Newton) method is exactly the same as that of TOA when the error source of the range measurement is only an IID white Gaussian noise. In case of geo-location and indoor positioning, however, multi-path or NLOS(non-line-of-sight) error is frequently appeared in range measurements. Though its occurrence is random, the multipath acts like a bias for a stationary user if it occurs. This paper presents the comparisons of error characteristics between TOA and TDOA positioning in presence of multi-path or NLOS error. It is analytically shown that the position estimate of TDOA is exactly the same as that of TOA even when bias errors are included in range measurements with different magnitudes. By computer simulation, position estimation error and error distribution are analyzed in presence of range bias errors.