• 동력기계공학회지
• /
• 제14권2호
• /
• pp.55-59
• /
• 2010

In the study, it is considered sporty car as 1400cc entry cars using sound generator. These cars are required special sound quality, also sporty sound quality. The operational principle of this sound generator system is that on the operation of the engine intake valves caused pulsating is to shake the membrane of the sound generator on the inside of the driver front dash panel through the intake manifold, which will deliver the required sound quality and tone. For the component constructed sound generator, main design parameters are selected and optimized using the daguchi's method. The results are as follows; The C2 sound level must be minimized and C4 level must be maximized. And also overall level keeps linear characteristics.

• 한국음향학회지
• /
• 제22권8호
• /
• pp.660-669
• /
• 2003

본 논문은 음원 근처의 홀로그램 평면에서 측정된 음압에 대한 상호 파워 스펙트럼으로부터 홀로그램 평면에서의 음압 분포를 구하고 획득된 음장을 공간 변환하여 음원의 음장을 구하기 위한 이론을 설명하였으며, 홀로그램 평면에서의 상호 파워 스펙트럼으로부터 모든 지점에서의 음압을 구하기 위해 비선형 방정식에 대한 Taylor 급수를 전개하고 Newton-Raphson 법을 이용하여 계산하는 방법과 음원 영역으로의 역방향 전파시 발생되는 오차를 줄이기 위한 파수 필터를 제시하였다. 무한 배플 내의 원판형 진동체 수중 음원에 대한 모의실험을 통해 결과를 고찰하고 제시된 이론을 검증하였다.

• 한국소음진동공학회논문집
• /
• 제16권11호
• /
• pp.1124-1131
• /
• 2006

This paper presents a novel method to determine sound power level(PWL) emitted by a travelling vehicle for road traffic noise simulation. The PWL is evaluated by the equivalent sound pressure level (SPL) measured by close proximity method and the sound power correction factor derived from the maximum SPL measured by pass-by method and the propagation attenuation of vehicle noise during the pass-by measurement. Using the method, we derive the empirical formula for PWL estimation in 1/1-octave and overall frequency bands for 8 vehicles (automobile, SUV, small truck, large bus, trailer, 3 dump trucks) tested at two road surfaces (dense graded asphalt, 30mm transverse tinning concrete) of Korean highway test road. The suggested approach, if securing sufficient data to represent the acoustic characteristics of all vehicle types, has il strong merit to be able to evaluate sound power levels for any combination of vehicle categories and traffic volumes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.421-427
• /
• 2006

This paper presents a novel method to determine sound power level(PWL) emitted by a travelling vehicle for road traffic noise simulation. The PWL is evaluated by the equivalent sound pressure level(SPL) measured by close proximity method and the sound power correction factor derived from the maximum SPL measured by pass-by method and the propagation attenuation of vehicle noise during the pass-by measurement. Using the method, we derive the empirical formula for PWL estimation in 1/1-octave and overall frequency bands for 8 vehicles(automobile, SUV, small truck, large bus, trailer, 3 dump trucks) tested at two road surfaces(dense graded asphalt, 30mm transverse tinning concrete) of Korean highway test road. The suggested approach, if securing sufficient data to represent the acoustic characteristics of au vehicle types, has a strong merit to be able to evaluate sound power levels for any combination of vehicle categories and traffic volumes.

• 한국소음진동공학회논문집
• /
• 제22권3호
• /
• pp.203-207
• /
• 2012

The noise emitted from an excavator has long been a cause of environmental disputes, while causing displeasure to the nearby residents. So, the ministry of environment adopted the construction machinery noise labeling system to encourage the construction machinery manufacturing companies to develop the low noise construction machinery voluntarily. But, as the quality of life improves, a growing number of people desire the comfortable and quite environment to live in. Under the situation, noise from the construction machinery has been a major cause for stress and complaints. When the noise dispute happened in the construction site, the sound pressure level of the construction machinery like a excavator was measured at the lot boundary of the noise victim's residence to judge how much noise damage occur. But the sound pressure level of the construction machinery is measured differently according to the acoustic environment of construction site and the measuring position, respectively, which makes it difficulty to judge whether the noise damage occur or not. As the sound power level of noise source is not affected by the acoustic environment of construction site and the measuring position, if we use the information of the sound power level, it will be easy to judge whether the noise damage occur and to establish the soundproofing measures. Therefore, we derive the sound power level regression model of the excavator to judge whether the noise emitted from the excavator damages to residents near the construction site. Also, the sound power level regression model of the excavator drawn in this paper will help construction companies to plan the noise reduction program in the construction sites.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(I)
• /
• pp.119-124
• /
• 2002

This paper considers the sound radiation characteristics of a craked rectangular vibrating plate, varying the orientation angle of a line crack. The vibration response of the cracked vibrating plate is obtained by using ANSYS, the acoustic theory based on the lumped parameter model is used to calculate radiated sound power. The radiated sound powers are computed with varying the orientation angle of the crack: i.e, 0$^{\circ}$, 45$^{\circ}$, and 90$^{\circ}$. It is found that characteristics of the radiated sound power are very closely related to the crack orientation, vibration mode and crack location.

• 한국해양공학회지
• /
• 제12권2호통권28호
• /
• pp.22-32
• /
• 1998

Many of steel structures having little internal damping consist of stiffened plates. In case that viscoelastic materials are adhered to the stiffened plates for the reduction of structure-borne noise, their effects are varied by the adhered position and dynamic characteristics of the structures as well as their material properties and adhered amount. In this paper, sound reduction effects of viscoelastic materials partially adhered to the different positions of a stiffened steel plate have been investigated by the measurement of vibratory velocity and sound intensity. The results show that optimal adherent positions of viscoelastic materials to reduce sound radiation power are the loop areas of modes.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 ITC-CSCC -1
• /
• pp.253-256
• /
• 2000

This paper describes a DSP implementation of a real-time 3D sound localization algorithm with the use of a low power embedded DSP. A distinctive feature of this implementation is that the audible frequency band is divided into three, in accordance with the sound reflection and diffraction phenomena through different media from a certain sound source to human ears, and then in each subband a specific implementation procedure of the 3D sound localization is devised so as to operate real-time at a low frequency of 50MHz on a 16bit fixed-point DSP. Thus out DSP implementation can provide a listener with 3D sound effects through a headphone at low cost and low power consumption.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 ITC-CSCC -1
• /
• pp.264-267
• /
• 2000

This paper describes a real-time 3D sound localization algorithm to be implemented with the use of a Bow power embedded DSP. This algorithm first divides the audible frequency band into three, on the basis of the analysis of the sound reflection and diffraction effects through different media from a certain sound source to human ears, and then in each subband a specific procedure is devised fur the 3D sound localization so as to operate real-time on a low power embedded DSP This algorithm aims at providing a listener with the 3D sound effects through a headphone at low cost and low power consumption.

• 소음진동
• /
• 제7권6호
• /
• pp.919-929
• /
• 1997

Induction motors are used in many areas to transform electrical energy to mechanical energy. In the design of an induction motor, not only energy efficiency but also noise becomes an important factor. To effectively address the noise problem, it will be convenient if one can see where and how noise is generated and propagated. In this study sound radiation by an induction motor is visualized using cylindrical acoustic holography. To minimize the bias error by window effect Minimum Error Window(MEW) is used. Its performance is verified by numerical simulations. Based on these theoretical understanding, sound pressure measurement with an induction motor are performed. Not only sound radiation are visualized but sound pressure level and sound power level are also estimated. Results show that the main source is located at nearly bottom part of the motor and the total sound pressure level is 49dB, which satisfies the guideline value suggested by the KS C 4202.