• Journal of the Korea Concrete Institute
• /
• v.20 no.5
• /
• pp.653-660
• /
• 2008

The purpose of this study is to analyze the optimal mix design of the sound absorption material that is made from perlite and various binder systems for noise barrier wall. The polymer cement slurry which is made from two types of polymer dispersions, and silicone type inorganic material are used as binder. The test specimens are prepared with various polymer cement ratios, binder ratios, and tested for strengths, freezing and thawing and sound absorption performance by the tube and the reverberation room methods. From the test results, the difference of sound absorption coefficient by the tube method is a little recognized, however, noise reduction coefficient (NRC) of test specimens bound by the polymer cement slurry is in the ranges of 0.48 to 0.51. They are a little higher than those bound by cement only, and are lower values than recommended value of 0.7 by the Ministry of Environment. However, the sound absorption coefficient of test specimens at low frequency range of 250 to 500 Hz by reverberation room method shows very high values as 0.84 to 1.00, and 0.57 to 0.77 at the high frequency. The test specimens with polymer cement slurry binder have a good balance between performance and cost, and have proper properties in strengths, freezing and thawing resistance as sound absorption material for noise barrier wall. It is apparent that the good sound absorption material can be produced according to the optimum mix design that is recommended from this study.

• Journal of Forest and Environmental Science
• /
• v.40 no.2
• /
• pp.90-98
• /
• 2024

This study analyzes the characteristics of sound-absorbing materials made from forest by-products of the deciduous tree species Zelkova serrata (Z. serrata) by evaluating their sound absorption performance. Accordingly, sound-absorbing materials with varying sample thicknesses, leaf sizes, and drying conditions were fabricated. The sound absorption properties were measured using the impedance tube method via middle-type measurement tube (100 Hz-3,200 Hz). The sound absorption properties were evaluated using the average sound absorption coefficient (ASAC), which was calculated from the measured sound absorption coefficients at 250 Hz, 500 Hz, 1,000 Hz, and 2,000 Hz. The ASAC value significantly improved as the leaf size increased to 0.5×0.5 cm², 1.0×1.0 cm², and 2.0×2.0 cm². The ASAC values under the two drying conditions were similar. There was no significant difference in ASAC according to the leaf size under the air-dried leaf condition, with a thickness of 2.50 cm. The highest ASAC value according to the sound-absorbing material thickness was 0.47 at a thickness of 2.50 cm and leaf size of 2.0×2.0 cm² under the air-dried leaf condition. In addition, the variation in ASAC was 0.23, indicating that the sound absorption performance according to leaf thickness was more significant than the difference in absorption properties according to leaf size. A sound absorption coefficient (SAC) of 0.4 or higher was observed across the measurable frequency band (100 Hz-3,200 Hz). Furthermore, the SAC values with respect to leaf size and thickness were close to 1 in the high-frequency range above 2,000 Hz. Therefore, it is considered that sound-absorbing materials using Z. serrata leaves are advantageous in the field of absorbing noise in a high-frequency band of 2,000 Hz or more, and it is better to manufacture a thickness of 2.50 and 2.0×2.0 cm².

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.644-654
• /
• 2019

In this study, the gas permeability, sound absorption coefficient, and sound transmission loss of the Paulownia tomentosa wood were estimated using capillary flow porometry, transfer function method, and transfer matrix method, respectively. The longitudinal specific permeability constant of the Paulownia tomentosa wood with a thickness of 20 mm was 0.254 for the control sample and 0.279, 0.314, and 0.452 after being subjected to heat treatments at $100^{\circ}C$, $160^{\circ}C$, and $200^{\circ}C$, respectively. The gas permeability was observed to be slightly increased by the heat treatment. The mean sound absorption coefficients of 20-mm thick Paulownia tomentosa log cross-section for the control sample and after being subjected to heat treatments at $100^{\circ}C$, $160^{\circ}C$, and $200^{\circ}C$ were 0.101, 0.109, 0.096 and 0.106, respectively. Further, the noise reduction coefficients of 20-mm thick Paulownia tomentosa log cross-section of the control sample and after being subjected to heat treatment at temperatures of $100^{\circ}C$, $160^{\circ}C$, and $200^{\circ}C$ were 0.060, 0.067, 0.062 and 0.071, respectively. The mean of sound transmission loss of the 20-mm thick Paulownia tomentosa log cross-section was approximately 36.93 dB. Furthermore, the gas permeability and sound absorption coefficient of the heat-treated Paulownia tomentosa discs slightly increased depending on the heat treatment temperature; however, the rate of increase was insignificant.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.902-907
• /
• 2002

An equivalent electroacoustic circuit approach of estimating the sound absorption coefficient for parallel perforated plate system is proposed. The proposed approach is validated by comparing the calculated absorption coefficients of a parallel single layer perforated plate system with the values measured by the two-microphone impedance tube method for various porosity and the number of perforated plate. The sound absorbing performances of parallel and series perforated plate systems are compared and discussed from a standpoint of frequency bandwidth with sound absorption. The proposed approach is further extended to the parallel double layer perforated plate system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.197-200
• /
• 2010

In some cases it is important to be able to measure not only the total sound intensity on a panel surface in a vehicle cabin, but also the components of that intensity due to sound radiation and due to absorption from the incident field. For example, these intensity components may be needed for calibration of energy flow models of the cabin noise. A robust method based on surface absorption coefficient measurement is presented in his paper.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.9
• /
• pp.709-716
• /
• 2002

A practical method of predicting the sound absorption coefficient for multiple perforated-plate sound absorbing system was developed using transfer matrix method. The proposed method was validated by comparing the calculated absorption coefficients of a single layer perforated plate with the values measured by the two-microphone impedance tube method for various porosity and spacing of the perforated plate. The developed transfer matrix method was further applied to estimate the multiple layer perforated plates and it is shown that the estimated absorption coefficients agree well with the measured values.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.5
• /
• pp.555-562
• /
• 2014

Characteristics of carbonized fiberboard such as chemical materials absorption, electromagnetic shielding, and electrical and mechanical performance were determined in previous studies. The carbonized board therefore confirmed that having excellent abilities of these characteristics. In this study, the effect of density on physical properties and sound absorption properties of carbonized fiberboards at $800^{\circ}C$ were investigated for the potential use of carbonized fiberboards as a replacement of conventional sound absorbing material. The thickness of fiberboards after carbonization was reduced 49.9%, 40.7%, and 43.3% in low density fiberboard (LDF), medium density fiberboard (MDF), and high density fiberboard (HDF), respectively. Based on SEM images, porosity of carbonized fiberboard increased by carbonization due to removing adhesives. Moreover, carbonization did not destroy structure of wood fiber based on SEM results. Carbonization process influenced contraction of fiberboard. The sound absorption coefficient of carbonized low density fiberboard (c-LDF) was higher than those of carbonized medium density fiberboard (c-MDF) and carbonized high density fiberboard (c-HDF). This result was similar with original fiberboards, which indicated sound absorbing ability was not significantly changed by carbonization compared to that of original fiberboards. Therefore, the sound absorbing coefficient may depend on source, texture, and density of fiberboard rather than carbonization.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.48 no.2
• /
• pp.174-179
• /
• 2012

A new absorption material, cellulose sponge soaked in cement, was made for anechoic water tank and its acoustical properties were investigated by pulse methods. The sound absorption coefficient a (dB/cm) of the material was obtained in the frequency range of 40~120kHz from the echo reduction ER (dB) and insertion loss IL (dB) data. The result was averagely 1.8dB/cm higher than the sound absorption coefficient a (dB/cm) of cork-filled rubber which is one of the most effective absorption materials. The wedge (1.2~5.0cm long) type absorption tiles were made with this new material. The echo reduction ER (dB) of the absorption tile with 5.0cm wedge measured in water tank was higher than 20dB in the experimental frequency range.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.367-370
• /
• 2001

Various shapes of the noise barrier frame and construction of the sound absorbing panels are studied. It is found that insertion of the sound absorbing panel into barrier frame results in the decrease of the sound absorption coefficient, while the empty frame shows a peak around 250Hz. Using double sound absorbing panels with air gap can increase sound absorption coefficient up to NRC 0.85.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.410-414
• /
• 2010

Two different types of polymer-modified mortars(PMM) were prepared with recycled PET and fly-ash. One is rigid PMM and the other is flexible PMM which are based on the composition of recycled PET. Their mechanical properties including friction coefficient measurement and damping characteristics such as sound absorption were investigated and compared with the commercial PMM such as epoxy PMM and PET PMM. The result from mechanical properties indicated that the rigid PMM could be competitive with the commercial PET PMM. The measurement of sound absorption coefficient showed that both rigid PMM and flexible PMM had much better damping capacity than commercial PMM. However, the friction coefficient of rigid PMM revealed that it would be suitable for the use as floor material.